10" Tire doesn't fit on my Xiaomi M365 Pro 😭 & How to replace the tire 🍻🍕

[@warrengray610]

After fitting a monorim front suspension I've noticed there is room for larger than standard size wheel, this is largely due to a bracket supplied with the kit that mounts the mud guard higher.

[@gtone339]

The 10" inch tyre will come in handy for the Ninebot Kickscooter MAX (supports 10" inch tyres) but there's no need for it since the Ninebot MAX comes with 2 10" inch tubeless tyres installed on the get go. Looking forward to it near Q4 2019! :)

[@marklilly7197]

I am new to the scooter world. I bought a Navee N40 I just put no flats because I take mine to and from work. No time for flat tires. I got a flat after only 10 miles. Gone over 100 since with no flats. It's a bit bumpy but doable.

[@Skrek1988]

and its not an issue with the tube valve remove side on motor and remove the small plastic piece that hold the valve in place. and to get 10inch to fit turn the washers around so that tab that sticks out is pointing up. there u go clear... dont do extra work u dont need to

[@jb-lu4vo]

Thanks for the video and I am happy with my original CTS tyres from Xiaomi Mijia M365, now they come with much better quality. Take care mate

[@Cenayus]

Jesus Baltasar Muro Barroso hi, so does the pro version come with better quality than the M365?

[@annashealthylifeeverything8583]

Hello I'm thinking about buying a scooter with solid tires 10". But if I don't like the comfort of solid tires (it's the one with holes) is it possible to change to pneumatic tires or you can only switch from pneumatic tires to solid ones? The scooter I'm thinking about is a nordic version with name VEIO.

[@fordboyzzzz]

Seen some on Ali says 10x3.0 - are they a good fit?

[@orange42]

I've got a nice pipe that fits over the spanner handle. Everything is easy with it. Hey what about removing that front mud guard? Has to be something else one can put in there instead.

[@PirateWasHere]

yeah like plastic bag 😂😂, I will try again 10" soon but I will be more prepeared :)

[@vedranart]

@@PirateWasHere so, you plan to install, fit 10 inch tires on m365?

[@ThePaigeMa5ter]

I did the exact same thing with the plastic piece and it’s a lot easier to get in there now. It was actually impossible for me to get it on there without widening the hole. I noticed now they point a little strangely when placing but must do....

[@rushchris]

Bro may i know what is that battery that you took from the bag? It is extra batt for the scooter?

[@alisasuperrobot]

My first time to change 10 inch tire on my pro m365 is same like yours it doesn't fit I expense how many hours but I bought a new tire from Amazon it fit perfectly is just easy to put like 10 minutes seriously I just put the tire in to microwave for 1 minute and it's done. This is the I use aibiku 2pcs 10 x 2 Outer Tubes for Xiaomi M365 Electric Scooter Modified Tire

[@user-cw3nb8rc9e]

Did you try again to do anything about 10" tires? These look really really good (the shape of tire) and size is great. It would be a pitty not to have them on.

[@caipas111]

The extra battery you have. Do you sell and send them? In the country i live at its hard to find materials for making it.

[@ptescreen18]

oliver napolitano I would buy also

[@WiewiurTV]

Order it via AliExpress

[@jb678901]

@@WiewiurTV Some Ali sites use cheap Li-ion batteries. Others use name brands. Another youtuber has tested multiple ones and recommended this seller, who uses branded LG or SAMSUNG Li-ion cells: "LiitoKala" I bought one and the price was competitive and reasonable.

[@lukas.malaiska]

Hey, yesterday I just ordered exactly these tyres. Should they fit on regular M365?

[@michak7793]

Hi, I have some problems with regular m365 with 10 inch tyres. Today i've tried rear one and i've failed. I have used mod for rear bumper so it sits a bit higher. But wheel touches rear led connector so i have no idea what is going on.

[@lukas.malaiska]

@@michak7793 do you have support for that mudguard?

[@hectorsilva3053]

@@lukas.malaiska did you finaly fit the chao yang 10" tire at the back does the tire fits? i have it but i coudnt fit it

[@lukas.malaiska]

@@hectorsilva3053, no they doesn't sit on the rim well. I think they are actually not for M365. Then I gave them to another person that he would fit them on his M365, but he didn't manage too. So he returned them back.

[@oneeyedrone4293]

Just seems like it would be much easier to split the rim in half with the hex bolts that hold it together rather than prying it apart like you did. Its not a car or bike rim, since it comes apart, just take the two halves apart :)

[@connorcruz6249]

The rim is all one piece, all the bolts do is hold the armature of the motor together.

[@emecata3919]

Hey..the antipuncture type must be installed before you mount on the wheel..with the tire lonely...jaa..but this tyre must be good to m365

[@RosenZ_]

Hi Pirate. I know this isn't relevant to the video, but i just recieved my fiido d1 10ah bike after watching your reviews :D I was wondering what kind of chain lube you use, as the chain seems to be kinda different from normal chains. Also, did you tighten every bolt when you recieved the bike, or is it fine from the factory? Cheers from Denmark! :)

[@PirateWasHere]

Dont ever use any lube for chain, yeah check every single screw 👀. I been living in KOGE for 2 years , cheers 🍕🍻

[@RosenZ_]

@@PirateWasHere Alright thanks for the answer! Køge is a very nice city :D What tyre pressure do you use? :)

[@PirateWasHere]

No idea But tire has to be hard like rock

[@Shadow_of_STLKR]

I had same problem with unscrew this bold BUT IT ISN'T ALUMINIUM! and pulling tube like this with a hammer isn't the best idea. Edge of this tape cut my inner tube few days after i put it in tire.

[@skeelo69]

i don't know if this is an age related thing (i had my M365 since 2017), i had to replace the controller on my M365 as the one i had stopped working...anyway i bought an Original Mi Controller (Note...it has to be an Original part, not some knock off), anyway, i received the latest controller from the M365 Pro , and WOW !! , my M365 has extra torque, it has extra speed...it's an M365 that is drug assisted 😅

[@jcreedy20]

Well it will be better as the pro controller is pushing more amps down the motors neck. The motor in the pro has a wider stator and slightly different windings on the motors core so it can handle a bit more power, but there isn't a dramatic difference so it will probably feel almost the same in terms of performance as the pro.

[@jcreedy20]

kzbin.info/www/bejne/pH7KYYGgeMZ5nM0

[@satish8299]

Can i buy a battery pack made by you? You are very handy guy, and the explenation is very good. In normal becycles powder is also used, i wonder why is the need for powder? Is the powder to absoorb humitidy?

[@panospallas7697]

It is to reduce friction between tube and tire mate

[@TheBassIsTakingOver]

use another wrench or a insert half of the wrench into a poll for added leverage. a lot less likely to strip the nut that way. plus I can remove the front nut with one finger and no bruises on my hands

[@YellowAstra]

use soapdissolved in water to fit it properly

[@mohamedmussa8891]

I’m having big problem replacing back tyre. I had one puncture. Each new tyre I’ve put in becomes ripped when I’m putting it in. Any advice how to deal with this annoying problem ?

[@gixxer4646]

Just go with the tube and new tire to a bicycle shop in order to replace it, they are working with rubber all day.

[@TheChazas]

Can not wait when Segway Ninebot Kickscooter Max arrives and see how it compares to M365 Pro, it will be rocking 10 inch tires.

[@gtone339]

Definitely a pain in arse to remove the front Nut off! I struggled to remove my one & I accidentally damaged the nut due to excessive amount of rotating force, instead I decided to get my E-scooter serviced at the official Xiaomi Mi store 2 weeks ago & now I got it back last Friday and I had to pay a total of $69 NZD for their service (brought my spare tyre to reduce service fee under $100).

[@orange42]

Haslips tires, mt wellington, auck does it for $10.

[@gtone339]

@@orange42 Its $30 now, discount is gone gone now. going to Evo Cyles NZ (North Shore branch), they charge $15 to replace the tyre & tube as long as I supply them a spare.

[@orange42]

@@gtone339 Oh thanks, will update my website page with that info.

[@skeelo69]

dude, what you should have done was attach two spanners together to increase the rotational force, did good for me 😅

[@gtone339]

@@skeelo69 Thanks for the tip!

[@ptescreen18]

Yea we need to see what the problem is and sort that out really . I think there is a certain type of tire that fits , I hear the 156mm inner diameter tire fits ?

[@PirateWasHere]

Yeah all my 10" got 156mm inner diameter

[@ptescreen18]

Pirate well then it will be the screw that holds the front mudguard, change it and do another video mate 👍🏼

[@NicksStuff]

Can you cut a bit of the rear of the mudguard and change the screw?

[@jammydodger5253]

Can u use original tube?

[@MrEzPc]

don't you add something to the forks that adds the extra space so the 10" fits perfectly?

[@barenekid9695]

It may be possible to fit a 3 or 4 mm spacer to the axle retention slot The slot seems long enough to allow this

[@ZeNex74]

or take off the motor cover slightly move the plastic then put back on after tube is in

[@xlaimuxllt]

you should try running set up tubless and also so easy to modify the mudguard by heating it up and remoulding.

[@zxnkairo]

I appreciate that liquid drum and bass in the background

[@pedro.bernardo]

10 inch tires on Xiaomi is recomended when using Monorim Suspensions

[@smilodon1550]

Good Job!Thank you.Grüße from Germany.

[@AlexEttelis]

Thank you for the hole increasing tip. I didn't manage to get it out the first time, so I cut the bad tube, and accidentally cut my finger :( Couldn't get it in, maybe with the bigger hole it will get in

[@jb678901]

Either a bigger hole or a smaller screw. I would go for the bigger hole myself. To each his own.

[@Ardious]

You can just lift the cover and remove the plastic part, that is making the hole narrower.

[@CorneliusBudianto]

Spzjulien share how to install 10" in pro, but its in french. It's not only need shorter head screw, but need to install a specific 10" tire model. He mentioned in his blog to find 10" tire with 6.35cm diameter

[@ptescreen18]

Cornelius Budianto I thought it had to be 156mm inner diameter

[@CorneliusBudianto]

sorry, my mistake, its not inner diameter. I believe its width. quote from spzjulien blog : "you get 1"5 (6.35 cm) in diameter"

[@CorneliusBudianto]

kzbin.info/www/bejne/nXaaf6acaLuAq9U

[@ercangoe2592]

Thx for the video! U have a link for the anti slip tires ?

[@PirateWasHere]

Sure check description : Thicken HQ Tube for M365 bit.ly/ThickTub8M365 CST best anit slip tire bit.ly/2UOAaUM Gocomma CST bit.ly/2FoulDk for only 16$ Steel Tire lever bit.ly/2PjmBXJ Anti Puntcure tape bit.ly/2mk6Jqc

[@jaydog78]

I use a socket wrench to loosen it just a tip

[@marcinlag1]

Próbowałeś jeszcze raz przejść na 10’tki tylko z płaską śrubą z przodu?

[@PirateWasHere]

tak , wejdzie calosc tylko oponka i tak nie wchodzi idealnie na felge , czuc takie mini bicie :/

[@marcinlag1]

Pirate dzięki za odpowiedź!

[@atrujillo7836]

I don't have a pro or would be able to figure it out like I did in first gen. I'm thinking of going 11 or 12 since nobody has done it

[@gtone339]

Or wait for the Ninebot MAX E-scooter, you can order yours via Indegogo for $599 USD (will go back to RRP $799 USD). www.indiegogo.com/projects/ninebot-max-ultimate-electric-scooter-by-segway#/

[@skeelo69]

Pirate , there is a solution to the tyre problem, the front nuts have a spacer which raise or lower the tyre, turn them around. The front mud guard has a protruding nut, change it for one which protrudes less.

[@vedranart]

Do you have some link that shows this? ty

[@skeelo69]

@@vedranart kzbin.info/www/bejne/Z2SraquJaJuakLc

[@skeelo69]

Of course, you could grind down the head of the front bolt if you want to.Thread it in some nuts(for protection), use a vice grip and then grind down the head.

[@mauriciovazquez158]

Exactly!! I change it for a flat head screw!! Work better!!

[@Bofinkenn]

if you remove the 6 screws holding down the motor plate. You can remove and insert the valve much easier.

[@teosto1384]

Definitely. I just discovered that myself a while ago. Removing the motor is one chore in itself as it's cylinder like so you will have to lift it evenly from both sides, but it allows you to fit the valve without interfering with the rim itself. Worth it definitely.

[@jk-mm5to]

I cut off the back of my fender and reversed it to fit 10x2 but won't fit 10x2.5

[@pawelberge]

I strongly recommend you tire levers from Park Tool. The one which have plastic outside and metal core inside. You will avoid to scratch the rims.

[@radek2287]

Tool reference?

[@pawelberge]

@@radek2287 ? :)

[@Moe_Lester_fromUptwn]

Got those. Man! I can't recommend those enough; especially if like me, you're sitting on solid tires. No way!, I could've mounted em without these.

[@CabrioDriving]

7:41 You should have glued that anti puncture tape before you put them on rims. I would use glue OR even two side tape so this anti punctutre tape sticks to the tire inside. two times like you suggest.

[@dreamepicness]

LOL Xlite!! you got some good FRSKY transmitter there buddy!

[@JamiePineappleWyatt]

5:06 make sure to sand the holes with super fine sandpaper, then polish them. It’ll stop any bits from creating unwanted running and punctures my friend :D Great video so far, removing tyres is never that hard when you know how isn’t it? ;)

[@SergiyZavarykin]

you will flaten the thread if you continue tightening with insane torque.

[@mauriciovazquez158]

You forgot to replace the top screw !! Replace with with flat!!

[@antoniomolina7231]

THIS!!!!!!IS THE SOLUTION!!!!!!

[@randomstuff-wg6nj]

will This Work For The Original not the Pro ?=

[@PirateWasHere]

I would love to know 😎🤪

[@randomstuff-wg6nj]

oh ok

[@Bergwacht]

@@PirateWasHere I bought some, if they arrived from China here I can tell you. Maybe in 2 weeks.

[@atrujillo7836]

If you buy the spacers it will. I bought mine as a kit it had a spacer for the back fender, a spacer for the kickstand, a shorter bolt for the fork and I rerouted the brake light cable to fit the wheel

[@Bergwacht]

@@atrujillo7836 That sounds wonderful, exactly this kit I already have here - I'm just waiting for the tyres ^ ^ But I did not think about the cable. White I know but what the additional screw in the kit is: D

[@projectxmarketing3431]

You need mount 10x1.75 tire. I have 3 pcs. They are 5mm smaller and they should fit to your pro scooter

[@projectxmarketing3431]

I mount 1 week ago 10x2.5 tire to back whell on my sooter and is looking amazing. Now i work to buy front suspension and mount 10x2.5 tire on front whell on my m365 and m365 pro.

[@projectxmarketing3431]

it is possible but I had to bend the scooter frame a little at the back. it was worth it because the tire is wider than the fender. 10x2.5 tire is 65mm wide. I put it in the frame from the m365 so it will also come in the m365 pro. the point is that I have a Chinese version of the scooter and they have bigger fenders. 10 inch tires without scooter modification are included in Chinese versions of non-company m365 copies. so what can you do with this? look in the Internet for other fenders that will fit 10 clowe tires. it is possible! You have to try and order several versions of a fender from China and see which one fits with a 10 inch tire. the difference in driving is really noticeable. when I mounted 10 inch tires on my m365, it felt like I was riding the maxg30. much more stable and not unequal. tires act as shock absorbers. it's really hard to try, because this change gives the scooter a second life.

[@elmtube1]

What powder did you use?

[@hirootto2771]

You can use talc

[@poolec404]

Agh the taranis x-lite case -- nice transmitter :)

[@enam9000]

You sound a bit like Arnold Schwarzenegger a little.

[@proxyhx2075]

Hmmm

[@wilsonasbahljr.3677]

Could someone say the specs / measures for the front mudguard screw?

[@TheLondonCyclist]

M6 X 30mm flat head

[@rubosrex7303]

Take off the mud guards, 3-d print ur own and screw them externally on the fork.

[@user-cw3nb8rc9e]

That's the idea! 3D print ones, that fit!

[@Anomyzer24]

Remove the front mudguard to put 10 inch wheels.

[@jarisipilainen3875]

4:10 nothing to fix it works like it designed.valve not slip inside wheel when you try pump air. would be sad remove tire again?.and you not need drill plastic of you got it out without drilling it go in and out with plastic in there.its rubik cube you need figure it out xD

[@mohammedazeez2108]

Has anyone tried putting a tubeless tyre on a xiaomi and is there a video?

[@mauriciovazquez158]

I have the honeycomb tires are the best.

[@jackhunter3292]

For 10' tyres you need the extension for front fork... and extension for kickstand and back fender.

[@vedranart]

can you link those mods here? Thanks! And is there a video of someone doing that modification?

[@klausbrinck2137]

Really now, you could have removed that mudguard, just to show us if the mudguard is the only problem!!! Now we are not a bit wiser than before...

[@rmnnrw]

Not only the front wheel can be a problem. The rear wheel can also interfere with the frame

[@mauriciovazquez158]

Yup that mudguard has a screw head that blocks the wheel from moving! Replace it with a flat head screws 😂😂 I had to learn the hard way for that!!

[@klausbrinck2137]

@@mauriciovazquez158 So, more or less, you have to replace just that screw on the PRO??? As thought the world weren´t full of flathead-screws, now really that wasnt´difficult to be named in this video...

[@mauriciovazquez158]

Replace the screw make sure it's the same but use flat. Also make some modifications such as : the mudguard from the back needs to be bit higher you can by adding a small piece of metal that is screw to the mudguard ( you know those 3 screwes that are holding the mudguard. Don't forget the kick stand ( you can by those pieces on Amazon or eBay ) needs a small boot that you can insert so the scooter can mount higher. The wire from the back light needs to be replaced because once you add the pieces to the mudguard it will short your cable and will not reach the plug .. Check the right pressure from the front wheel make sure u are using the right wheel because of the measurements are exact! That way you don't have to remove the mudguard or the screw. Aslo check that your scooter app make sure you you have the correct number of the wheel. If you think you made that change and nothing happen. Go to www.hackm365.com and down load . Here are my best pressure tire: Front wheel 49.3 psi - 3.4 bar 8.5 whell Back wheel. 52.2 psi -3.6 10' wheel. Front wheel. Between 2.6 and 3.0 bar Back wheel Between 2.7 and 3.0 bar You might have to pay some money for adjusting or if you want to multiple your speed .. To make sure the wheel is well adjust .. place scooter side way on top of a table insert the wheel realease some air , slowly spin the tire and you will be adjusting it .make sure you get a adapter that's goes to the pressure gouge then put air (that way you don't have pinch out it out it will adjust just fine) it will also help you by not release pressure on the tire.. check your tire pressure every 2 weeks or depending on how much the kilometers!!! Be careful when adjusting the firmware it will short your batteries life . In a sense that when you notice it's slowing down and pick up fast , that might not be the right firmware . That's is when you download the bineri numbers and add them to the flash . ⚠⚠WORNING ⚠⚠⚠ DO NOT stop or cancelled the flash while setting up the speed. Do Not Turn off Disconnect Bluetooth while operating the system . Don't move the scooter it will only result in damaging your dashboard and control unit. Check that your batteries are 3.9 volts on each cell ..( the app can read the cells)track your mile and you will be good..

[@mauriciovazquez158]

Forgot . Use the slime product for your inside tube you will have to used it just for more comfort.. don't forget to use baby powder inside the wheel so when you put the tube it will not slide hard against the metal..

[@barenekid9695]

Hmm... I ordered the Gearbest Gocomma (CST) tires from Gearbest (above link) the Aholes sent substitute tires.. Paypal then Refunded my $$ . .What an Ordeal ! Better :-) IF one fits a tire with a 156 mm inner diameter. Seems that IF one is removing a tire to Replace it ? Simply cutting the tires' Bead (without cutting the inner tube :-) with side cutters could make it So Much simpler. Removing the engine case cover allows one to fit the valve stem.. Easily.

[@OS-kt2ck]

There are some videos of how adjust the scooter for 10 inch tires. You would need a shorter screw in the front and 2 thick rubbers for the back side as well as for the stand piece. Then you would have much more space between the tire and the scooter itself 😏

[@orange42]

no, this is the pro, not normal m3

[@goclunker]

I am gonna try to fit 70/65 6.5s on my ninebot max to trick it into going faster

[@SEAMASTERHELLAS]

You don’t drill the valve hole. Only remove the inner plastic by unscrew the black metallic cup, doctor !!!!

[@PirateWasHere]

But I like to dril it xD

[@bighorse215]

Tire lube my friend next time will make the job alot easier

[@TheLondonCyclist]

Was that your excuse when she said it hurt? No lube...

[@eSUBA94]

jakie wymiary tych 10" ?

[@rafatarka4265]

10"

[@eSUBA94]

@@rafatarka4265 wymiary nie średnica

[@azeyt2154]

Original music 🤟👍👏🤙🤙

[@nowymercedes]

It would be easier if front wheel could be disconected from energy cable (an contact disconector).

[@barenekid9695]

Could? fit 3 bullet connectors inside the Fork's wire cover

[@gerrymcdonnell5970]

Thx for trying

[@Cenayus]

Hey guys did he just used regular baby powder? Like Johnson’s and Johnson for example? The nice parfumed one?😄

[@PirateWasHere]

yeah could be, BUT It has to be as clean as possible without any addons

[@Skrek1988]

a bit late here but the nuts are not aluminium... take a magnet and see if u dont belive it. alum=not magnetic / steel iron= magnetic

[@DylanFowler]

I wish this vid had come out a few months ago.

[@PirateWasHere]

why

[@DylanFowler]

@@PirateWasHere you showed the size of the spanner and the right tire to use. However 2 spanners and 4 different tires later I got there. lol

[@Nosci1020]

Confirmed that tire doesnt fit better take the biknight 10inch and not the chao tang

[@denishuber7758]

just use some soapy water....it works om every kind of rims

[@SuperBujo83]

Would this kit on Ebay www.ebay.com/itm/Xiaomi-mijia-M365-M187-complete-kit-for-10-inch-wheels-upgrade/283527129963?hash=item420388ab6b:g:txUAAOSwef9dEb8P In any way help? I was thinking about putting larger tires on a Xiaomi I just purchased to tackle more rough pavement. But upon reading this it seems the ID (inner diameter) of the tire isn't quite large enough for the rim. From what I read about the hollow solid tires, you loose speed and distance. So I don't think I'll be pursuing those for certain. Either way, thanks for the video. It was educational.

[@NickToland]

Such a pain in the arse to remove the 8.5 inch tires... I hate it!

[@PatrikSelin]

Nuts are easier to remove when first using silicone oil.

[@FlyingScot911]

Nothing, and I mean nothing, touches AIM lube from PlanetSafe Lubricants for breaking stuck bolts. And it is also the best bearing lubricant for your wheels. Reduces friction and eliminates rust. You can even get nuts and bolts red hot and use it because it is not flammable and loves heat.

[@parasutadiguma]

Nice review......

[@PirateWasHere]

thanks...

[@cukrzyk2137]

Pierw pomyślałem że to PashaLondonSchool

[@PirateWasHere]

Kto ?! xD

[@cukrzyk2137]

PashaBiceps xD

[@McGinty.]

this was traumatic as fuck but vaseline helped

[@walterkersting1362]

That’s nice how they let use tools and do little projects for yourself...

[@Moe_Lester_fromUptwn]

Wore out one of those Lil screws, and now I can't get it out. Even tried a screw remover. ima go get a beer, I give up! Can't figure out another way.

[@TheLondonCyclist]

I did the same shit with the mudguard screws. They are shit. Maybe try and super glue an Allen key to the screw and twist it out haah

[@Moe_Lester_fromUptwn]

@@TheLondonCyclist 😂 dropped it off at the mechanics. Dunno what/how but he got it out. And I'm short $60. I'm sticking to solid tires from here on out Lol.

[@TheLondonCyclist]

@@Moe_Lester_fromUptwn $60? Are you crazy? All he probably did was grind a small line and turned then with a straight head screw driver lol. Could have done it yourself.

[@Moe_Lester_fromUptwn]

@@TheLondonCyclist I'm telling ya. I stood there all like 😕 when hearing em numbers. Learning experience indeed. And thanks for that suggestion.

[@TheLondonCyclist]

@@Moe_Lester_fromUptwn Get one of those small hand held angle grinders... Those mini ones. They have small grinders on the end and can fit into small spaces. Also could tape a flat head in-between the Allen bolt and jam it in and twist out.

[@sunjunme]

You ruined the rim completely for a tubeless air-filled tire 🥶

[@PirateWasHere]

it was not tubeless ;0)

[@TheraPi]

Remove the mudguard

[@sc0tty319]

1:09 i'm stuck in here the bolt won't loose..any tips?

[@Elias-jo1cc]

this was hard to watch as a mechanic

[@PirateWasHere]

@Elias-jo1cc how so ? I thought good mechanic dont need to watch simple videos like this one

[@Elias-jo1cc]

@@PirateWasHere Because its faster and easier taking out the engine. Just wanted to see the 10", how or if you would heat and bend the mudguard. "no one is better than you ;)" Pretty uncalled for, just because its my profession & hobby doesn't mean I can't still learn, not know everything or simply watch something I already know? There's always room for improvement despite having a lot of experience. New tools to find. Techniques and so on brother.

[@Denso481]

Have you tried this? it's a 10" mod kit and looks super simple actually: www.ebay.co.uk/itm/Xiaomi-scooter-Mijia-m365-m187-complete-kit-for-10-inch-wheels-upgrade-10-RED-/253681333326

[@zsocaesfeherke]

Say it again, please: "SHIIIT" :D

[@PirateWasHere]

😂😂😂😍🍕🍻

[@mariomedrano861]

Shiieeeet this one out and leave a like 👍

[@-morrow]

we've got a real clay davis here ;)

[@danpettis1675]

lose the damn fender .she'll fit..

[@Miszel]

nice english man

[@Guilourenco1]

Very bad job and the tyre is fater than normal!!!! YOu could also remove the mud gard....

[@razornightling6673]

Having a bigger wheel slows it down! Don’t even try this it isn’t worth it

[@byalexgreenenergy142]

Mas torpe no se puede!!!

[@mareklaszczych6752]

Panie, gownosrubka z gownolitu:) oczkowym Panie, u siebie mialem ten sam problem:) Co do wentyla, niestety siedzi w plastiku, trzeba uskrobac troche zeby byl wiekszy luz, no nawkurzalem sie na maxa z tym badziewiem:) Generalnie dlatego daja 2 detki zapasowe...

[@PirateWasHere]

Dobre waldek dobre 🍻

[@eduardoblasques9024]

🤦‍♂️🐴

[@PirateWasHere]

🐈🔥

[@jobysebastian3922]

😅😅😅😅😅

[@PirateWasHere]

Wait what ?! 😂🍕🍻

[@ManDone88]

Dislike !!!

[@PirateWasHere]

🤪😮