1794 Flex I/O Install and remove Properly

How to install and remove Allen Bradley 1794 Flex I/O modules from DIN Rail.
Hopefully after viewing this video you will be able to install and properly remove without damage the modules and bases in a Flex I/O system. Not removing properly leads to damaged pieces and then you have junk rather than a recycled product that you can resell.

[@jamiuadeagbo1444]

Thanks for this wonderful and peaceful assembly explanation without stress

[@abplctestbench759]

You are very welcome.

[@muqkhan786]

Appreciate you for share your knowledge. It helped me and saved me time.

[@abplctestbench759]

Hi: You are very welcome.

[@thankgodinnocentisaac9650]

Thanks for the information and replies. It is educating and guiding.

[@abplctestbench759]

You are welcome

[@edenlumbanraja5541]

This is wonderful. Thank you

[@echo2082]

Thank you for sharing some good and useful information!

[@abplctestbench759]

Your welcome

[@ralphramsey82]

Thanks for taking the time to make this video

[@abplctestbench759]

Your welcome. Hope to get some more done soon.

[@presidentpoopypants1448]

Thanks for putting this up. At work we install of lot of these. I've made it a point to always look at the bottom of the module for any bent/misaligned pins before installing. Been a few times they were bent a little and putting them in with any force caused bent/broken pins. Thanks again for posting your videos.

[@abplctestbench759]

Hello Jay - Your welcome. Thank you for the comment.

[@sauravsalil1]

Thanks it helped me a lot

[@abplctestbench759]

You are very welcome - glad my video was of use to you.

[@TB-oe4vr]

I have some of these. How do you set them up to just test and try it out? I'm worried that some software that is no longer available is needed.

[@abplctestbench759]

Hello TB: Which Flex I/O modules are you worried about? There are many of them and all are current. Can you be more specific in your question? I have a number of videos on my channel that use the 1794 modules. kzbin.info/aero/PLApJy6_fcuvi_kx1MeMJjYus6rphDwVma You can also check the Rockwell site for product lifecycle status list - www.rockwellautomation.com/en-us/support/product/product-compatibility-migration/product-lifecycle-status.html

[@chandrashekarm1347]

Can i change module online (while Running the plant). By forcing all the tripping values. Tc/RTD module

[@abplctestbench759]

Hello: As soon as you pull out a module it will fault the adapter and all the modules in that chassis will stop communication with the processor. You would be best to stop the process and change it then. It will take you less than a minute to change out the module. When it powers up the processor will write the configuration to it.

[@HM-zv9uo]

Thanks it was helpful for me.Is it possible to remove terminal(wires) from the terminal base?

[@abplctestbench759]

Yes it is - with the correctly sized screwdriver.

[@dougm1985]

thanks for making this .

[@abplctestbench759]

Your welcome - hope it makes working with these easier

[@dougm1985]

@@abplctestbench759 yes it will, do you have a video on swapping out the module with a replacement. we have a red light on ours. cycled power a few times not resetting. waiting on a replacement.

[@abplctestbench759]

@@dougm1985 Hi Doug: No Videos on swapping it out - normally I power down and remove and then re-install. Would need to know which module it is to begin to assist you. But as I mentioned before to others - confirm your wiring and if that is good then check your configuration in the program. If you are making an exact swap then I would have to suspect that you have 2 dead modules but that is normally a low probability.

[@dougm1985]

@@abplctestbench759 on the general tab is a box for bootp. its not checked , i have two of these units and both are not checked. what happens if i check it? my moduel has gone from red to green , just sitting there, my net work status light is off thanks in advance

[@abplctestbench759]

@@dougm1985 I take it from your comment that you are having a problem with the 1794-AENT communication adapter module? If so is it a series A or a series B with the 3 switches? I have another video on the AENT adapters on the channel.

[@abdelssami]

thanks for the very informative video , we have a flex I/O 1794 where i work and i would like to know if it needs any kind of configuration and what software do i need to use in a case that i would like to replace it with another one, thanks in advance

[@abplctestbench759]

Hello: If you are only removing and replacing a module with the same one - no configuration of changes in software are needed. I recommend that you power down the module and adapter before removing or inserting a new module. If you add another base and module to the system you need to use the AB PLC software for the series of PLC processor that controls your system.

[@jn6676]

Do you have any tutorials about configuring sn-1747 Scanner Cards to talk with the 1794 ASB adapter modules, do you need to have a certain number of terminal bases/interface cards connected with comms to work correctly is my specific question. Many thanks

[@abplctestbench759]

Hi James: Sorry I do not. The manual is available on the AB site. www.rockwellautomation.com/search/ra-en-US;keyword=1747-SN;startIndex=0;activeTab=Literature;spellingCorrect=true;facets=;languages=en;locales=en_GLOBAL,en-US;sort=bma;isPLS=false;sessionID=a4a9321e-7c6a-0264-923f-8d22ff65ad2a;deepLinking=undefined

[@mikemckenzie7817]

Thanks 😊

[@abplctestbench759]

Your welcome

[@temitopefamuyiwa7043]

Please,I need your technical advice. We have 1794-IRT8 installed and intended to change one of the 1794-IRT8 module that's faulty to 1794-IT8 in which the 1794-IT8 doesn't Power ON. What could be the cause?

[@abplctestbench759]

The way the bases are wired are slightly different. You have to check your wiring diagrams before changing over. You also must configure the new module in the program. Without having the module in my shop it is not possible for me to check out what is going on with it. You can also go to this site and post a question. You may get a better idea. www.plcs.net/

[@temitopefamuyiwa7043]

Thank you for your Swift response. I really appreciate.

[@abplctestbench759]

@@temitopefamuyiwa7043 Your welcome

[@ثقافةعامة-ظ7خ]

Hello sir. Can I contact you? Because I have a problem and I cannot solve it. Can you help me? Thank you.

[@abplctestbench759]

Hello: please explain your problem. Because of the number of scams on KZbin I don't have an email contact posted. Once you tell me your problem I will see what we can do. It is currently Sunday here in Canada. Where are you? Thank you

[@ثقافةعامة-ظ7خ]

Monday

[@ثقافةعامة-ظ7خ]

I am from Yemen

[@ثقافةعامة-ظ7خ]

I want to send you some pictures

[@ثقافةعامة-ظ7خ]

Do you have Telegram?