I get the Ridetech 4-Link Cradle installed and I clean up some of my welds.
Пікірлер: 24
@TheLooper0 Жыл бұрын
I really enjoy your videos, had a chuckle at the righty tighty , righty loosey line.
@ElrodsGarage Жыл бұрын
Thank man! I try to be funny.
@ParadiseBayCustoms Жыл бұрын
👍 Nice progress!
@ElrodsGarage Жыл бұрын
Thanks man!
@johnmilner7603 Жыл бұрын
Congratulations on the subscribers. 😊
@ElrodsGarage Жыл бұрын
Thanks John!
@DoubleRRestorations Жыл бұрын
Looks great, Congrats on the 1k
@ElrodsGarage Жыл бұрын
Thanks a bunch Russ!
@MrFireman164 Жыл бұрын
Congrats on 1k subs, car is looking good 👍
@ElrodsGarage Жыл бұрын
Thanks Roger!
@GoGoGarage Жыл бұрын
Great Progress.
@ElrodsGarage Жыл бұрын
Thank you. I keep grinding on it.
@OldCarGarageUSA Жыл бұрын
Congratulations on 1K sub's!
@ElrodsGarage Жыл бұрын
Thanks a bunch!
@g3garage Жыл бұрын
Great info in this video. Congrats on hitting 1K subs!
@ElrodsGarage Жыл бұрын
Thank you.
@stevecanyon23 Жыл бұрын
Hey Elrod, good to see the work continue. I always wondered how / where the water entering from above actually drips out. I had a look on my '68 the other day and found a small fold in the two sheets of metal, poked in a piece of wire and saw it come out in the low corner (pass side) of the cowl cavity. Only reason I could see, was the hole for the electric vent. On the driver side that spot is not directly visible. Long story short, I had an incredible amount of debris (leaves etc. and sand from previous sandblasting) in that lower pocket area on both sides that I had to vacuum out in order to get those run-off holes free.
@ElrodsGarage Жыл бұрын
Thanks Steve! I assume these cars were meant to be cleaned out periodically. Dirt and debris build up in certain areas and cause them to rust out. Or it's just planned obsolescence, they can sell more cars that way. Cheers man!
@firstgenerationgarage2803 Жыл бұрын
Hello brother love the video as for those bolts that holds the Fender at the bottom you could cut that out and repair it it's better in the future believe me I just made a video a couple of weeks ago on that repair check it out I know you are capable of doing it Really enjoying your videos keep it up
@ElrodsGarage Жыл бұрын
Thanks Luis! Yeah, I may fix those the right way to avoid a problem later. It'll be easier to do while it's on the rotisserie. Cheers man!
@Novarider723 ай бұрын
Hey, what's going on, man? Hey? Check it out. What was the kind of rust killer you use when you put those outer cowls back on to that Camaro? What was the brand again?
@ElrodsGarage3 ай бұрын
Hey man! I'm just livin', L-I-V-I-N. That was Fast Etch from Eastwood. It worked really well.
@Novarider723 ай бұрын
I thought it was some rusty limb spray
@ElrodsGarage3 ай бұрын
@@Novarider72 This guy mixes up his own sauce and it seems to work quite well. kzbin.info/www/bejne/g2mkkJ2jjqmokJIsi=-Fgb3tYp4DxSwkq4