Great videos: Detailled and crystal clear. Thanks to these I was able to ressussitate a 1977 Evinrude 4 HP that was otherwise heading for the scrapyard..
@jde37514 жыл бұрын
Just finished rebuilding the carb on a 1979 Johnson 4hp, thanks for the help!
@jimocaudill4 жыл бұрын
I really appreciate your video on replace the vro to regular fuel pump I just did mine over the weekend it works perfectly thanks 👍😁
@peteryeung1116 жыл бұрын
Just what I needed...about to start my first rebuilt of my 74' 4 hp...perfect and thank you!
@WayneTheBoatGuy2 жыл бұрын
This carb is exactly like the carb on my Evinrude 2!
@TheDtrolinder2 жыл бұрын
I wish as you put everything back together you would explain what part you are installing. Thanks
@justinprince95078 ай бұрын
The high and low speed needle nuts….how tight do you make them?
@kevinhedgecock50466 жыл бұрын
I have a mid 80's evinrude 4hp and there is no air cleaner or filter...should there be ? This is my 1st outboard experience....btw...no lower engine cover either
@scottyfixer4524 жыл бұрын
Do you know what the initial settings are for the high and low speed on a 1977 Johnson 4 hp seahorse
@MrIvan2 жыл бұрын
the video starts with the carburetor off, do you have one where you are taking it off? went through the 3 previous ones and didn't see it
@MrIvan2 жыл бұрын
For anyone looking in the future, it's in the video "1975 & 1977 Johnson / Evinrude 4 HP Inspection" kzbin.info/www/bejne/eIepXoWkpJllmqM at around 17 mins in
@scottyfixer4524 жыл бұрын
What was your carburetor rebuild kit number for this particular engine
@randiedelrio53404 жыл бұрын
Where can i find carburator kit repair Many thanks
@michael.thordson5 жыл бұрын
looking at the carb (opposite side that bolts to the engine), why would gas be coming out of the top right hole? I had this issue arise so I replaced the needle/seat, float and gaskets. motor ran good for approx. 14 hrs of travel over multiple days and then after less then an hour of running one morning it came back. what to look for next? thanks.
@BrandonsGarage5 жыл бұрын
Junk/particles in gas tank clogging up the seat? It shouldn't happen, the float valve should cut off gas flow into the carb, it isn't, and the carb is just filling up. I suppose you could clean the float shaft and mounting holes up a bit, perhaps corrosion there would prevent it from closing? Or the shaft is bent. I don't know, but good chance your problem is with the float/seat.
@michael.thordson5 жыл бұрын
@@BrandonsGarage looks like I have another project to add to the list. Ill give that a look though. Did anything more ever happen with that 1975 Johnson 4hp powerhead teardown project? did you ever do a rebuild video?
@clydecampbell24816 жыл бұрын
Rebuilt, the carb on my 71 yachtwin. Checked the reed plate. I see sparks from both plugs out on the engine during cranking, but motor still won't start. Help?
@BrandonsGarage6 жыл бұрын
Set the float correctly? Top plug wire isnt on the bottom cylinder?
@clydecampbell24816 жыл бұрын
Brandon's Garage double checked the float after watching your video. It's pretty level. The plug wire marked up is attached to the top spark plug
@clydecampbell24816 жыл бұрын
Replaced the two ignition capacitors / condensers. Engine now starts. Need to replace the high speed needle valve and packing gland nut. Internal threads are messed up.
@KissmyBasss3 жыл бұрын
Can you increase hp by swapping to a larger carb? 4hp to a 6hp?
@KissmyBasss3 жыл бұрын
Linkage doesn't matter much to me, also why not a Mikuni type using an adapter?
@BrandonsGarage3 жыл бұрын
Pistons are larger on the 6 hp
@keithsage15934 жыл бұрын
Do you answer questions?
@BrandonsGarage4 жыл бұрын
I try to
@keithsage15934 жыл бұрын
I have no fuel filling the float bowl so I have ordered a new float needle, spring and seat ,now can I tell if my gloat is upside down?
@giom4206 жыл бұрын
What size fuel line do you have on there?
@BrandonsGarage6 жыл бұрын
going to the fuel pump, or from fuel pump to carb?
@giom4206 жыл бұрын
Brandon's Garage Been working on a 1980 4hp evinrude. I don't think my problem is with the fuel line ..rebuild the carburetor but still dies when I throttle up .. idle fine.. i don't know whats wrong