1993 MR2 3SGTE Gen5 Build E24- Rear Brake Caliper Refresh

[@darrenwitcomb2056]

Just about to rebuild 1 x rear and this was spot on to watch before I tackled it

[@bitingantz]

Thanks for the feedback and very happy it was helpful.

[@jamesjames215]

This was very helpful, as you say no videos on KZbin that cover this,,I can now crack on with mine 👍👍

[@bitingantz]

Appreciate the feedback. Thanks for watching

[@jamesjames215]

Just a question, were the oversized piston seal's ok , any issues at all? Thanks 👍

[@bitingantz]

@@jamesjames215 hello. No issues they are working great.

[@jamesjames215]

Just going to refit my rear calipers soon is the handbrake self adjusting or do I have to keep adjusting until I get it right? Thanks 👍

[@bitingantz]

@@jamesjames215 if the hand brake was working fine before it should not require adjustment. If not you have to adjust under the car where the two cable meet.

[@Jursaw]

Are there any rubber seals in the parking brake mechanism? I’m getting them powder coated but I don’t know how to disassemble the parking brake assemble

[@bitingantz]

I dont beleive there are any seals if you separate the parking brake from the caliper. But, i have never pulled that section apart.

[@Jursaw]

@@bitingantz I just looked up another video and there is a o-ring on the threaded shaft. I will probably make a video on how to take it apart.

[@bitingantz]

@@Jursaw thanks for the update.

[@brianrichards7151]

Thanks for this j,ust going to do all 4, front and rear really helpful.

[@bitingantz]

No problem. I tried to explain as best as i could.

[@pxckbl6883]

Thanks for this video!❤ solved my issue

[@bitingantz]

Your welcome, pls share the channel with your mr2 friends.

[@chriskaye1997]

Hi, what was involved in removing the e-brake to get the whole calliper and bracket off, please? I have one slide pin that has totally seized, so I can’t swing the calliper up to access anything :/

[@bitingantz]

Hello, just remove the pin on the end of the ebrake cable where it’s connected to caliper. After that slide out the cylinder that the pin was in and cable is separated from main caliper.

[@ericcontreras6347]

where did you purchase the cube tool?

[@bitingantz]

Got it off rockauto but amazon has some better options as well

[@bitingantz]

www.amazon.com/Orion-Motor-Tech-Compressor-Replacement/dp/B01FW3U26G/ref=mp_s_a_1_1_sspa?crid=3P3Y240D354HC&keywords=brake+service+kit&qid=1642432079&sprefix=brake+servic%2Caps%2C82&sr=8-1-spons&psc=1&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUFOSkFWRkdPOTY0UDImZW5jcnlwdGVkSWQ9QTAzOTU3MjAxTkU3QlhPSFMwMjhIJmVuY3J5cHRlZEFkSWQ9QTAwMTcwMDlPWUw5Ukk5WURPUzYmd2lkZ2V0TmFtZT1zcF9waG9uZV9zZWFyY2hfYXRmJmFjdGlvbj1jbGlja1JlZGlyZWN0JmRvTm90TG9nQ2xpY2s9dHJ1ZQ==

[@bitingantz]

www.amazon.com/Lisle-28600-Disc-Brake-Piston/dp/B0002SQUFY/ref=mp_s_a_1_4?crid=13LOP29U58N69&keywords=brake+service+cube&qid=1642432120&sprefix=brake+service+cube%2Caps%2C79&sr=8-4

[@pinkpearl428]

Hii