Good video. I appreciate the clarity on the light disconnect.
@eddiebunya41269 ай бұрын
Enjoyed your video thanks for sharing
@alwallis20008 ай бұрын
Great video
@donaldharden4075 Жыл бұрын
Careful around the filler neck with power tools. Fuel vapors can ignite off the drill. Had a buddy that taped the vent holes up on his dewalt and it still flashed on him. Cost him his eyebrows and a good pair of Levi's.
@tcmits36996 ай бұрын
Funny you mentioned sparks from power tools around fuel fill. Here in NJ you don't pump your own fuel. Pulled up to a gas station at night, the attendant opened the fuel door, l get out to unlock fuel cap, my fingers must've been close to the bed or fuel door, l heard and seen the loudest,bluish spark ever. Static electricity should also be taken serious. Fruit of the Looms lived to see another day😊
@timjarvis59683 жыл бұрын
Good one Everybody else is taking tail lights out, creating work, making it more complicated than necessary
@randomherolhd33 жыл бұрын
Thanks Tim.
@rickhorney34233 жыл бұрын
nice straight forward video thanks.
@randomherolhd33 жыл бұрын
Thanks Rick.
@maxseed47306 ай бұрын
Must have been a Hull technician
@randomherolhd36 ай бұрын
Yes sir.
@maxseed47306 ай бұрын
@@randomherolhd3 10 4.. played the rate of DC from 03 to 07..
@dkeith452 жыл бұрын
T55! Ah-ha! Largest torx I have is a T50 and too small. It's to the store for me tomorrow to get the larger bit now. Thx OP!
@randomherolhd32 жыл бұрын
Thanks. How did it go?
@dkeith452 жыл бұрын
@@randomherolhd3 Three came out using a two foot long breaker bar, one snapped off, one I was able to cut the top off using an angle grinder and last one I had to use a cold chisel to cut the steel around it then the bed came off. Bummer now is the gas tank where the fuel pump fits on is bent inward somewhat. Not sure how I'm going to fix that. JB Weld maybe?
@DudeInWalmart3 жыл бұрын
Should have sprayed the underside with cosmoline. That nasty gooe whould have preserved the truck for a million years.
@LouNigro4 ай бұрын
I own an 88 Ranger GT - i am in need of the fuel filter housing - do you have one for sale? Thanks Lou
@leastfavoritek3v2 жыл бұрын
Did you have to disconnect the brake lights ?
@MustangsTrainsMowers2 жыл бұрын
A 2006 7’ longbed box minus tailgate and lights is right at 200 pounds. I need to remove the bed from my 2009 which has had 4 separate collision damages to it. I call it the ding ding Ranger.
@jamsocrane2 жыл бұрын
Did you buy new bolts and nuts? or reused?
@randomherolhd32 жыл бұрын
I'm gonna use new fasteners. Though, I am tied up on other projects and haven't finished the Ranger yet.
@Andrewfrazer-fs4dk11 ай бұрын
do you have to remove the bumper to do this??
@tylerryder45689 ай бұрын
No
@danielpierre8043 жыл бұрын
I have a 2002 ford ranger edge my bed is regular I would like to know if the steps side beb will fit on my truck
@randomherolhd33 жыл бұрын
Yes, should fit.
@joshmelton56772 жыл бұрын
Would a 97 Mazda B2300 be the same steps?
@351cleavland2 жыл бұрын
Should be.
@dkeith452 жыл бұрын
One thing I noticed, for my '97 Mazda is those three fuel inlet screws were 9/32". No other socket would remove them. 7mm was too large and 6.5mm too small.
@maxseed47303 жыл бұрын
I had a 98 same color.. real pos
@joniguzman72173 жыл бұрын
Is a 02 bed same as a 97 ?
@randomherolhd33 жыл бұрын
Yes.
@carlthelongshoreman19793 жыл бұрын
You asked the question I was going to, thanks man
@DavidHernandez-ue4fz Жыл бұрын
@@randomherolhd3 how many pounds and you think 2 people can pick it up to replacement?
@randomherolhd3 Жыл бұрын
@@DavidHernandez-ue4fz I don't know how many pounds. I do believe 2 people would be able to lift the bed.