How to Replace Exhaust 07-11 Honda CRV

[@1AAuto]

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

[@ortizrony7438]

Where can I buy it

[@Acehunt21]

I have a 99 CR-V and have to rebuild my exhaust; have been looking for someone to walk through those basic steps! A1 Video bro, keep it up

[@shimazutoyohisa2382]

Give or take what would be the price of this repair and replacement. My 09 crv probably has the same or a very similar issue. Also in your opinion, what exhaust system/muffler would u recomment me install? Id be willing to get the top of the line brand/type if it meant it would last a little more. I have an indoor garage so i would be able to maintain it fairly well and avoid too much rust from weather.

[@balrog006]

What type and size of nuts bolts and washers did you replace the studs with?

[@johnduvall5]

Any videos on replacing the cat and dealing with the rusted bolts on the header?

[@stevekee2005]

Perfect video guys... thanks.

[@justin_time]

Thanks for posting this! It was a huge help!

[@1AAuto]

+Justin Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-1AAuto-c

[@congeenunu]

@@1AAuto you

[@MrCuckoobox]

Given the age and weathering and the fact that hangers have stretched , it would also been beneficial to replace them. After rust, broken or worn hangers are the leading cause of exhaust failure by causing stress on the system through strain and excess vibrations which leads to cracks. The life of that replacement will be shorten by the very fact that the hangers were not replaced.

[@scrubs026]

Do you guys sell a complete set of this exhaust system? Need to replace mine

[@1AAuto]

+scrubs026 Please check out our website directly to help find the parts you need for your specific vehicle 1aau.to/m/Shop-1AAuto-c

[@zackfrostic3303]

So I have the exact same problem with my CR-V. Is the only way to fix this is to replace the whole muffler and exhaust? I was hoping to just reconnect them with a new falange or something?

[@jaymadre5996]

Same as zack frostic and Matt ... I have the exact same problem with my CR-V. Is the only way to fix this to replace the whole muffler and exhaust? I was just hoping to reconnect them with a new flange or something?

[@fattirebeer9]

The rust point shown here in this video is a COMMON problem among all CRVs. This video is instructing you to replace the entire Cat back system. Little did I know this is NOT the cheapest solution. You can buy a universal flange from any autopart store and weld it to the hanger it broke off from. This site has a great write-up. www.crvownersclub.com/threads/exhaust-flange-repair-writeup-2007-honda-cr-v-ex-l-navi.210244/#post-1625822

[@1AAuto]

+Mike Choi Thanks for the tip!

[@matt6940]

...same as Zack Frostic... I have the exact same problem with my CR-V. --- especially the rusted area at the flange by the muffler-- Is the only way to fix this is to replace the whole muffler and exhaust? I was hoping to just reconnect them with a new flange or something?

[@audis6m]

You can fix it but you have to extend and weld the hanger more to the front of the car cut off old connections and connect the exhale with something like that allegro.pl/oferta/lacznik-zlacze-tlumika-rur-wydechu-obejma-64x125mm-7546180597

[@d.c.1235]

You can literally just use 4 hose clamps. 2 around the sides of the exhaust line that are disconnected, two to pull them together on opposite sides of the flanges’ springs. Might get some rattling but I haven’t had any.

[@nicolekrug6597]

D. C. Pictures please

[@santaneco1111]

Excellent!

[@1AAuto]

+santaneco1990 Thanks for checking us out!

[@davidhenryhenry5462]

I need to know how to do a horn replacement replacement

[@kamalbeesla5733]

Good informative video thanks 🙏 for uploading

[@1AAuto]

+Kamaljit Singh Thanks for checking us out!

[@ortizrony7438]

Where can I buy it

[@d.c.1235]

Common problem with these CRVs. Save yourself time and money; only need 4 worm hose clamps. One around each side of the flange that flares out, semi-tight, then one on top and bottom to pull them together. First fully tighten the first two, then the two pulling them together. Mines been running strong for 3 years.

[@1AAuto]

+Devon Collins Thanks for the feedback!

[@madeinusa7759]

Well done

[@christinaphillips5933]

Amazing ! Great 👍 job

[@oldschoolrepairshop2866]

Funny my 08 rotted out in the same spot, TIP: spray alittle WD-45 on the hanger to help remove them. I never had one slide off

[@MrCuckoobox]

Silicon Spray/Grease or Red Rubber Grease is better because is "rubber friendly."

[@joebagofdoe4762]

This project would have been great for a flange repair kit!!!!!

[@1AAuto]

+joe bagofdoe Thanks for the feedback!

[@deminybs]

wanna hear something messed up???? Put new struts on my civic yesterday and test drove for about half an hour, fixed the issue , that's awesome 😎😎 but decided to go for a second drive before bed just for fun and downshifted into second and my exhaust separated .....lmao in an instant went from so quiet you gotta watch the tachometer to sounding like my previous car....with broken exhaust lmao.... at least this is the very tail end where mine broke so pretty sure I can fix it myself

[@scrubs026]

Do u have this item online? I need this

[@1AAuto]

+scrubs026 Thanks for checking us out. We do not currently carry these parts. 1aauto.com

[@blacksmith2586]

Same shiit on my 2010 muffler

[@gustavoherrera5719]

You forgot about last hanger,if you eliminate the last one nothing going to happen?🤔🤔🤔🤔

[@loyaltyndrespect24]

Wao, i can do this to my crv, not rock science.