√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*
@MsJbraswell13 жыл бұрын
Correction, meant that the tension clips built into the pad should rest on the caliper assembly.
@onetimer1005 ай бұрын
Overall great instructional video straight to the point and very clear and concise. I will say as others have noted the pads were reinstalled incorrectly, for this brake set on this vehicle. The brake pad springs indeed stay on the outside and are not meant to be shoved on the inside, inbetween the pad and the hardware. This is evident if you go back and watch the initial removal. Look closely and you can see they were installed properly last time... with the spring pads on the outside It's a common mistake and I've learned my lessons having owned an outback.
@lukemazza60272 жыл бұрын
Please update the video to include a note about correct placement of the brake pad return spring. As others have noted it should brace against the outside of the caliper frame, and not tucked inside. I have to redo one side of my brake job after following this video.
@martybarry51583 жыл бұрын
That was the best, clearest instruction I’ve ever watched. Thanks!
@1AAuto3 жыл бұрын
+Marty Barry Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
@sgould68624 жыл бұрын
As a previous commenter said, @14:50 the spring is indeed installed incorrectly. The end of the spring does NOT go under the tab on the pad. It goes on the outside against tab on the metal clip. This is how the pad was installed before you took it apart. It's also how the springs on my Outback looked when I did the brakes just now. You're not the only one to make this mistake. Several other videos out there do the same thing. Not sure if there are any safety ramifications, but putting the spring under the pad is definitely incorrect. Otherwise, great video.
@1AAuto4 жыл бұрын
+Steve Gould Thanks for the feedback!
@jasonrodgers87803 жыл бұрын
Agree! However, was so difficult to get pads to stay with the return spring in the correct/on-top position (non OEM pads with their non OEM metal backings) that I had to put the caliper bracket on THEN put the pads in and HOLD them in while I put the caliper on. Also, on passenger front I incorrectly put the return spring tucked in like video gal shows. Leaving for now....will be a good experiment 😄
@ericmoss83442 жыл бұрын
Correct... it took me a minute to figure it out as the spring in my opinion is designed to push the pad away f/the rotors so they don't 'ride' the rotors over time. Plus if you put the spring in how she showed it, the pads I used wouldn't fit as they are a snug fit w/the spring outside the metal hardware. If that makes sense... not the easiest brake job I've ever done in 35 yrs of wrenching, but doable if you know how it goes back together. :)
@zamiryi4 жыл бұрын
In 10+ years of doing brakes on ALL makes and models I have never seen ANYONE open the system just to retract the pistons. The bleeder screws are usually stuck or rust/welded, the piston bottoming out and caliper hanging below the master cylinder reservoir level is a guarantee to lose fluid while taking in the air. So now you turned a 30 min brake job into a 1.5 hours of soak the bleeder screw, hope it doesnt brake off, bleed the brakes when you are done.
@1AAuto4 жыл бұрын
+zamiryi Thanks for the tip! We'll pass this info along to our production team.
@yassinem34433 жыл бұрын
Great Video! Very informative and helpful. But DO NOT OPEN THE BLEADER PLUG! If you do, you will let air into the brake lines and they will need to be fully Bled. I confirmed this by calling my local Subaru Dealer. I did this and had to pay a mechanic to bleed all 4 of my brakes because there was air in the lines. It cost me $200.
@maxtp9482 жыл бұрын
Wow he ripped you of big time. Bleeding the brakes is a 20 min job and should not cost $200
@edwardchung35762 жыл бұрын
Agreed. I have never seen this done and was wondering why she did that.
@NinoInTheComments Жыл бұрын
Some fluid and pumping the brake for 200 bananas 😭😭😭
@panchovillaxx75 жыл бұрын
As always a great video !! When I do the brake job I never open the bleeding screw,is this necessary? I always unscrew the reservoir cap not the bleeding screw.
@jnepute3 жыл бұрын
That is how I have always done it as well. I think as long as the reservoir cap is unscrewed, you should be fine. I have never had a problem. I guess technically, you run the risk of damaging the master cylinder by forcing fluid back into the reservoir, but I have ever had an issue. Just compress the pistons slowly with the reservoir cap unscrewed and you should be fine.
@dougstringer53584 жыл бұрын
Couple of questions: Why replace the rotors at 65k? Also, how was your brake fluid container full after you bled the fluid out when you expanded the pistons? In addition, at the time you bled the fluid out, why didn't you have the cap off of the reservoir to allow a smooth flow and no air bubbles?
@michaelpark56812 жыл бұрын
I would like to know the answer to these questions as well
@Joeelectronicschematicsforauto4 жыл бұрын
Incredible and detailed video of how to do brakes
@andrewvillavicencio84968 ай бұрын
You are awesome! Great sense of humor as well. Thank you
@gymbo3434 жыл бұрын
At 14:50, I believe that spring is installed incorrectly. That part on the brake pad is a return spring, not an anti rattle clip. In the beginning of the video, where you removed the stock brake pads, notice how the clips were installed differently from how you guys installed it in the end.
@g.r.visentin90794 жыл бұрын
You're right on - I saw that right away, and I just did a 2016 Impreza with a similar spring. It has a little bump at the end that should ride on top of the extended metal on the side of the clip - as clearly shown on the old ones when removed (stop the video and look)
@wadehouk38233 жыл бұрын
I noticed the same thing with that spring. And if you put it where they said, it will catch in grooves in that hardware and not allow the pad to slide correctly.
@chriskunsak39632 жыл бұрын
Glad I read the comments because I was thinking the same thing!!
@Oscar999293 ай бұрын
Really awesome and thorough - good lighting and photography too. Thank you!
@robertcochran7103 Жыл бұрын
This is a really fabulous video. Thank you for posting it.
@turbochargers78412 ай бұрын
This video needs to be updated. I looked like a total idiot in front of my neighbor, doing it for her, thinking this would be good information. Now that I looked in the comments afterwards, I’m glad and also baffled that I caught that mistake after checking the other side by myself. This directional mistake could lead others not as cautious to improperly install their brake pads, rendering them unable to stop. This is a huge liability issue! Please correct!!👍🏾
@maxtp9482 жыл бұрын
Please explain why you open the bleeder screw when retracting the pistons and why that would be necessary on cars with an abs system. I’ve never seen anyone open the bleeder screw when pushing the pistons back. No matter what make or model or if the car has abs or not.
@David-ie7zn Жыл бұрын
I wonder about that too, I open the master reservoir cap so the brake fluid would remain in the system without air
@anthonyguess55285 жыл бұрын
Best video quality I've seen yet for brake job including the angles shot for everyone to see also very thorough :-)
@1AAuto5 жыл бұрын
+Anthony Guess Thank you for the great reply. We love to empower our customers by showing you how-to perform your own auto repairs while installing our high quality auto parts. Have a great day! 1aauto.com
@Timetraveler1111MN4 жыл бұрын
Anthony Guess yes that’s true it wa every easy to see all of what she is doing.
@raylabrecque82657 ай бұрын
Excellent commentary! Surprised you didn't use anti-sieze on the caliper bolts & lug nuts tho. Is there a reason?
@Turtle206 Жыл бұрын
omg, I have been doing it so wrong this whole time! thanks for this vid!
@raybrown1954 Жыл бұрын
Outstanding video. Excellent explanation and demonstration, professional workwomanship, shop, tools, procedures. Well done. And, thank you for no music!
@Natedoc8082 жыл бұрын
In addition to the many comments below outlining the incorrect spring placement, do not crack your bleeder screw unless you have a helper and want to bleed all four brakes; just crack the cap on the reservoir and compress the pistons slowly. Also, do yourself a favor and do not hand new pads or rotors with oily or greasy gloves, unless you want everyone to hear you braking.
@db1262 жыл бұрын
Nicely detailed. I do have some lingering questions regarding placement of the anti-rattle (return) spring as noted elsewhere in the comments. On a 2015 Legacy the spring caught on shim hardware when installed as shown. A very minor modification to the spring fixed that but I would have rather done it right the first time.
@saefhindi61843 жыл бұрын
I have seen other videos were they put a lubricant between shims and upper/lower side part of pads. What is your thought about that ? Tx
@gervaisdube18432 ай бұрын
If I get it good, the end of the spring on the pad goes outside against the bracket and act as a return spring for the pad. This prevents premature wear of the pad by pulling it away from the rotor. In that case is there any indicator that makes the disc squeal when the pads are due for replacement?
@mandirigmadelacruz5123 жыл бұрын
How about outback with ABS? This looks like a regular break replacement without ABS. Can u show also how to replace with ABS. Thanks
@MsJbraswell13 жыл бұрын
The tension clips on the pads are not supposed to rest on the outside of the carrier assembly. Not inside the clips as was done on re-assembly. I initially made the same mistake on one side but saw the proper way when removing the other side. Had to redo that side but caught it and fixed it before taking the car for a test drive. Something easy to do if not really looking closely when taking apart. Also wasn't sure if it was mentioned but the carrier assembly torque I believe is 85 ft lbs and caliper bolts where listed at 25 ft lbs (for those that do it to spec).
@tomgabourie9668 Жыл бұрын
Great Video, Do need to hear the 1st set of bolts torque number. Got the 2nd set and lug specs, not the 1st set.
@xksun40 Жыл бұрын
Well, looks like I’m taking it to the shop
@Toolaholic76 ай бұрын
No need to open the bleeder screw open,will not do damage to the ABS.Snap On now sells a special socket for getting to the upper caliper bracket bolt,part number is BTCS1.Put the torque wrench away,not needed too.Replace the hardware,some brake pad sets come with the hardware,one is powerstop
@peterbush79005 жыл бұрын
Excellent video! Anxiously waiting for the video showing REAR-brake replacement for the 2015 and above, Outbacks. Keep up the good work!
@1AAuto5 жыл бұрын
+Peter Bush Thanks for the positive feedback! The production studio is working hard on new videos!
@_P0tat07_ Жыл бұрын
@@1AAutobc. H -❤))AaaA
@906Mike Жыл бұрын
Can you accomplish the same result by removing the fill cap from the brake fluid reservoir instead of opening the bleeder?
@michaeldestories34124 жыл бұрын
Tech married? If my wife could do brake work like this woman has we'd be doing a lot more fishing on Saturday's ") Awesome work.
@ericcurley21905 жыл бұрын
The mechanic mentioned a tool for checking for moisture in the brake lines. Can you add it to your list of links above?
@ginotacobell309810 ай бұрын
I love your professional performanceand thank you for sharing 👍
@oliverdurrant18134 жыл бұрын
I'm so grateful for these videos. You just made my day....
@1AAuto4 жыл бұрын
+Oliver Durrant Thanks for checking us out! 1AAuto.com
@linac.71912 жыл бұрын
Thank you for the video! You helped us change my brakes today. Before we started my boyfriend said we should be watching the playoffs today instead of doing this, and then later on in the video she says “I’m not sure about you, but I’d rather be inside watching football” 🤣
@sgatwal5 жыл бұрын
Thank you !! can you also do rear brake job ?
@1AAuto5 жыл бұрын
Thanks for checking us out. 1aauto.com +Adam
@CamaroMan793 жыл бұрын
Why did you replace the rotor? Was it warped?
@itsme60263 жыл бұрын
you need silicone paste on the caliper pin, not brake grease
@EisBlade4 жыл бұрын
1A Auto always creates some of the best, and very detailed, maintenance videos. Thank you! I just bought a 2015 Outback. Are the two 8x125 bolts really needed to separate/dismount the rotor? With other vehicles, tapping the rotor in opposing lug nut pattern with a rubber mallet until it broke free worked just fine.
@tkinney803 жыл бұрын
I've always done the same but the last F150 I had that had the original rotors on from 2006 I had to heat, beat with a sledge and a long piece of steel off for about an hour to get both sides. I honestly didn't think I was going to get them off. I can only imagine in the rust belt the trouble they might have.
@alekseyrozentuler98434 жыл бұрын
very thorough, excellent step by step, just like reading shop manual.
@1AAuto4 жыл бұрын
+Aleksey Rozentuler Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1AAuto.com
@jamesgiant23424 жыл бұрын
Wow this video is amazing. So much preventative maintenance knowledge thank you.
@1AAuto4 жыл бұрын
+James Giant Thank you so much for the feedback!
@flat4forlife5882 жыл бұрын
Where can I get that ratcheting piston compressor? Thanks Also what happens if you compress the pistons without breaking open the bleeder screw. I see videos that don't do that step.
@mikemckee80663 жыл бұрын
I know it's been said now that I've read the comments, but a mate of mine was trying to use this as their first brake job and the 'anti-rattle spring' is not a thing on these cars. The metal spring presses on the outside of the caliper bracket. How you describe it you'd literally have to take the bracket off every time you wanted to change the brakes.
@lifeisgood0704 жыл бұрын
@ 12:50 where you use caliper grease, can you use permetex copper anti-sieze instead?
@phizz86942 жыл бұрын
Where can i get that torque wrench that is on the video @ 16:01 and not what is posting in your description? Thanks
@Timetraveler1111MN4 жыл бұрын
I didn’t know ... a lot of theses things. Cleaner spray, and clean a brush 🧽 Rotors coating, I didn’t know about the two bolt 🕳 holes 🕳 that push the rotors out! Bungee trick!
@willc.35595 жыл бұрын
Nice video, when I do mine, I always get a hardware kit 6or7 bucks. Didn't let the caliper hang, many do nice job.
@1AAuto5 жыл бұрын
+WILL C. Thank you for your positive feedback! We are happy we could help.
@who1969 Жыл бұрын
Great instructional video
@Timetraveler1111MN4 жыл бұрын
I best most mechanic 🧰 shops do NOT do the proper steps or the reasons why it’s done the way you explained!!
@kcirmusic14 жыл бұрын
Would this video be the same for the front brakes on a 2017 Subaru Outback 3.6R Limited?
@kmenzel50202 жыл бұрын
Great instructional video, thank you!!!!!
@scottriggs49504 жыл бұрын
Hello thank you so much - I have 2010 Legacy 2.5i - is it pretty much the same? i'd like to buy a front and rear brake and rotor job. just want to make sure you ship the correct parts - thanks again!
@1AAuto4 жыл бұрын
+Scott W. You will want to search our site for parts that are listed for your vehicle only. Thanks for checking us out! 1AAuto.com
@WiitRiic3 жыл бұрын
When you install the rattle clip is it midway inside the calipers or completely through the calipers? 14:50
@1AAuto3 жыл бұрын
+White Rice Thanks for watching! Looks like we go about halfway in the video. Once everything is put back together the spring will not slide out of the caliper, so as long as it is in position it really won't matter!
@WiitRiic3 жыл бұрын
@@1AAuto thank you!
@Brendalo13 жыл бұрын
why not keep the caliper closed & backfill the reservoir?
@jetboy7703713 жыл бұрын
I don't like the look of the install of the anti rattle spring on the new brake, it was different on the one that came off. OK it is called a "return spring " and it goes on the outside of the the pad clip. It must pull the pad away from the rotor when no brakes are applied. The one that came off was against the outside of the caliper frame and I think she hooked it inside the slot of the thin steel piece that lays in the caliper, which is right ? That spring is a return spring. "Be sure to install so that the pad return spring faces the input side of the direction of brake rotor rotation" " Correctly install the pad return spring to the supporting surface of the pad clip as shown in the figure."
@lifeisgood0704 жыл бұрын
Aslo why do you have to crack the bleeder when pushing in the pads on abs systems? Is there a vavle that could be damaged?
@SteveSnowman3 жыл бұрын
Very Well Done.
@bobkinsley7943 Жыл бұрын
Do not let the caliper hang unsupported
@Timetraveler1111MN4 жыл бұрын
Thumbs up 👍 very good tips and you give me confidence to do This myself!
@1AAuto4 жыл бұрын
+Jody Hakala Thanks for checking us out!
@Fern.the.explorer2 жыл бұрын
What's the conversion from foot pounds to ugga duggas?
@mackymac57543 жыл бұрын
No need to apply anti-seize on the bolts?
@josedhernandez77775 жыл бұрын
My hats off to the tech ! I would allow her to perform open heart surgery on me no joke ! Lol
@1AAuto5 жыл бұрын
Thanks for the feedback! We appreciate it! +Daniel Hernandez
@Keifsanderson2 жыл бұрын
Great job. Very nicely detailed instruction. Thank you.
@BanjoBrianExit125 жыл бұрын
Superb video!!
@1AAuto5 жыл бұрын
+Brian Kathenes Thank you for your feedback!
@MichalNalewajko5 жыл бұрын
Why do you dont measure the runout of break disc?
@harpoon_bakery1624 жыл бұрын
If just one pad was installed with the clip on the opposite side that it should be (attached clip spring thingy went back in on top instead of bottom. Do I need to take wheel back off, take caliper back off, and reverse it? Or will it be ok if i leave it? The wear indicator and also a spring tension-er are on the same side of each pad but it was having a hard time fitting in the downward position so it's in the up position. I'll take it all back apart if it's going to cause a safety issue. Thanks anyone for any help with this dilemma !!! I did bleed the brakes on all four wheels due to ABS. I also bedded the brakes with 30 stops of 30mph to 5mph per manufacturer's recommendation.
@1AAuto4 жыл бұрын
+Harpoon_Bakery Thanks for checking us out! You probably should correct the pad that is backwards (upside down) as that may cause a braking issue and uneven wear of the pad, rotor, and possibly even the caliper.
@edgarnavarro72645 жыл бұрын
very detailed job 👏🏽 thank you very much
@1AAuto5 жыл бұрын
+Edgar Navarro Thanks for checking us out!
@Izeba5 жыл бұрын
Question why do you have to bleed the brakes when you decompress it. Is it because you added Brake fluid as the brakes where being used ?
@1AAuto5 жыл бұрын
+Amir Gladstone You want to get rid of any air pockets in the brake lines.
@scottfirman5 жыл бұрын
Its best to drainoff some brake fluid from the master brake cylinder BEFORE retracting the pistons back in. NEVER open the bleeder to the atmosphere like that unless you plan on bleeding air from the system. Simply openening the cap on the master cylinder is enough to relieve pressure on the pistons. Replace the hardware EVERYTIME you do a brake job. Heat damages the hardware over time.
@ratedRblazin4204 жыл бұрын
Every time I have put on brakes (or had my mechanic) put on NON Subaru pads/rotors my brakes squeal profusely for thousands of miles. Why is that? As soon as I put factory brakes back on the squealing stopped.
@diggitallindadirt32834 жыл бұрын
Great video thanks nice tips 👍🏻
@FraxinusExelsior3 жыл бұрын
Very annoying that the instruction for the spring on the pad install is wrong, had to do it all over again, why don't u add info to the video informing of this?!
@1AAuto3 жыл бұрын
+Allmoge Thanks for the feedback! We'll pass this info along to our production team.
@errm19132 жыл бұрын
oh my, did you hang that caliper by the brake line!!! Then twist it?! Ow...
@denospyridon31264 жыл бұрын
I’m looking for your brake pads info 2015 Subaru Outback
@josedhernandez77775 жыл бұрын
Is it the same process for the rear ones ?
@1AAuto5 жыл бұрын
It is basically the same process if you have rotors on the rear. Thanks for the inquiry. +Daniel Hernandez
@josedhernandez77775 жыл бұрын
@@1AAuto is there any plans to make a rear brake pad replacement on a 2017 legacy ?
@TherealEggiejr5 жыл бұрын
Rears are electronic
@josedhernandez77775 жыл бұрын
@@TherealEggiejr Is there a different process to follow?
@BryanBalak4 жыл бұрын
@@josedhernandez7777 it's basically the same process, with the exception of the electronic parking brake on the driver's side. There are a few KZbin videos on how to remove it from the caliper and "unwind" it to allow you to expand the pistons.
@richardm62788 ай бұрын
19.9 foot pounds? My torque wrench certainly doesn't have that type of precision. I'm going to have to go with 20 foot pounds. Hope I don't snap the bolt.
@GlennsHardWired Жыл бұрын
How is this a good video when you've made so many rookie mistakes?
@tobymichaels81714 ай бұрын
Pro Tip: apply a thin coat of white lithium grease to the front and back of each brake pad before installation. You'll never have squeaky brakes again! You're welcome 😜
@jacquesdahan4945 жыл бұрын
I loved your video until you touched the pads with your greasy gloves,
@barrythomas64293 жыл бұрын
Dont worry too much about the negative comments.. Even Eric O gets critisized by the armchair experts.
@1AAuto3 жыл бұрын
+Barry Thomas Thanks for the feedback!
@catmango Жыл бұрын
I find it nearly impossible to insert the pads into the caliper with that clip. It’s simply not long enough to just slide them in easily like every video makes it seem. Here’s me angrily and sweatily squeezing the top of the pad with the clip up hard enough to allow the bottom to slide in, while also trying to pry the retaining clip thing out of the way. Truly the worst part of the job.
@Mr_Kingston Жыл бұрын
Informative only in clarifying the components before I tackle this. Other than that, technically correct but very sloppy.
@simonbengtsson9361 Жыл бұрын
You doing the brake pads wrong .. look How the old was
@tomthumb2057 Жыл бұрын
You don't need to open the bleed on an ABS system. You're making extra work adding complexity and introducing additional failure points. Redo the video...
@andrecampbell6914 жыл бұрын
Probably 99 out of 100 service workers don't open the blenders, just saying.
@1AAuto4 жыл бұрын
+Andre Campbell Thanks for the feedback!
@hooptienation70722 жыл бұрын
I’ve had both but bad luck with there parts do not purchase parts from this company. I had my ball joints break and cause more damage but better parts then the ones they sell
@eugenew6717 Жыл бұрын
No torque spec 🙄
@kevinmcgrath70838 ай бұрын
re the bleeder screw being opened immediately, she is right: kzbin.info/www/bejne/p6TSq6WKjct7pcUsi=x9VGabESKH0O3lEH
@yassinem34433 жыл бұрын
Great Video! Very informative and helpful. But DO NOT OPEN THE BLEADER PLUG! If you do, you will let air into the brake lines and they will need to be fully Bled. I confirmed this by calling my local Subaru Dealer. I did this and had to pay a mechanic to bleed all 4 of my brakes because there was air in the lines. It cost me $200.
@ericmoss83442 жыл бұрын
I've never opened the bleeder until I was ready to bleed the brakes... never heard the issue of opening the bleeder for ABS brakes. Hmmm