2000 Buick Century 3.1 liter engine thermostat

[@bobrichards318]

Very smart with the systematic way of removing and lining up screws, bolts, etc.

[@garycima5475]

Great video with (importantly) good advice!! Thank you sir!

[@charleshenderson1174]

Thanks

[@jasonrobbins4227]

Few extra bucks get a gasket maker tube. I'd suggest high temp gasket maker. Appreciate the location of the thermostat. I'm a bodyman watching you with the straight wrench was killing me lol Ratchet wrench is where it's at. That's if my electric ratchet don't fit and can't get a swivel on it lol. I'm spoiled great video thank you!

[@Rjj2721]

That's the wrong gasket maker type bud. Gotta be water pump/thermostat gasket maker. It's coolant(antifreeze) resistant. Normally around $8-10 for a small tube.

[@jerkjosh2969]

Great video now I know how to work on my Byuryurk

[@randytrader3026]

Im about to change the thermostat on my 2003.. same engine, same aggravating job.. thanks for the information

[@Jack51971]

I changed one of these n a 96 3.1 Lumina I had and it was not too hard. On my 2000 Century I tried last weekend and quickly found out that this is a PITA. May just go to a shop? Too much crap to remove. My stat is not closing all the way I think.

[@Jack51971]

Does it really need a gasket since the new thermostat has a rubber gasket around it? When you take out the original thermostat is there old gasket material on the tube that connects to the housing?🤔

[@garycox5589]

Start. from. Beginning

[@doublej4077]

It's not possible to put that thermostat in backwards is it ? I've replaced mine and the engine temperature is erratic , sometimes getting very hot.

[@kazilziya830]

Thank you for the tutorial. I've changed a few thermostats on a 3.1 engine and they are located in weird spot that isn't mechanic friendly. However , the water pump is a piece of cake.

[@marybass1654]

Hey where's the next step putting the I ring and thermostat back in

[@SlimmyDoThangs]

Thank u brother

[@krishnawainright15]

Is it the Same on 1999 Buick LeSabre???

[@lanalezcano1847]

Why did you have to replace the thermostat three times?

[@timsmith1899]

Park a 2000 Buick Century on a Hill with the front end about 10 inches or more, higher then the back end... When opening coolant system... That will force all the air to the top of the engine... Then with engine running at operating temp. With heater controls set on high... Bleed coolant nut on motor... ware radiator hose goes on motor near thermostat ... A brass threaded plug.... Sticking straight up... Plug is10mm I beleave ... once broker loose... use a light socket, or Tiny vice grips... Because coolant will be hot flowing from the bleeder hole... I used a wrench the first time... And the plug hit the driveway... 4 minutes to find it... And ir burned my fingers also... So mechanic gloves will be nice also... Last... do not over tighten.... Easy to strip hole ... I put car front on ramps works perfect... Also... if water pump goes out... must drain old coolant from engine, radiator, hoses, and coolant tank... Metal shavings from bad water pump bearing .... Will cause new water pump to go bad prematurly ... SUCKS but true.....

[@galactic904]

The Mechanical standard maintenance on these cars are not too friendly. It's a shame, because my 2004 Century, at 110,000 miles is great. I just use it for groceries and trips to the coffee shop, "Sunday driver". It cruises down the road like a charm.

[@ceed3d396]

Got 1999 Century I've been using as my main vehicle since 2011.

[@jamesbillet2168]

With all due respect to all of you out there. Before assuming it's the thermostat or water pump. Please be sure all of the air in the coolant system is purged. If air is trapped in the coolant system it will cause it to overheat and not let the coolant flow properly. Just fyi.

[@tellinthatruthgame8785]

Is that what the bleeder valve is for?

[@PeopleoverInstitutions]

How long does this take?

[@LH81633]

394.00 at Firestone😆😆😆 15.00 diy😆😆😆😆😆

[@LuStevens]

I lost a screw on the throttle body and now my car won’t start it starts abs cuts out? Any help?

[@galactic904]

Should i sell my 2004 Buick Century? Only 109,000 miles? Purrs like a tiger.

[@brandonravia4259]

I am vehicle illiterate, so I really needed to see the whole thing. Sorry bro

[@Bajaz-Bugz]

You know a 2001 Buick is supposed to use Dex-Cool right dexcool only

[@8tractlemans]

Thankyou for taking the time to show us how to replace this and where it is at. LOL I rember back in '89 having to replace the thermostat in my girlfreinds '85 Regal! Had to do it three times. Keep leaking. Thanks man.

[@schm147]

WRONG WRONG WRONG. You do NOT have to take off the bottom bolt on the housing. You can clearly see the bolt hole on that side of the housing is slotted, allowing you to remove the top bolt first and then LOOSEN the bottom bolt, not completely remove.

[@BullyGovJ4F7775]

Thanks for the info bruh! Love my buick 2002 century she never lets me down.

[@ianm2505]

Mine just the other week topped 330k :D same year 3.1 I get the same story from every single owner I meet lol

[@tellinthatruthgame8785]

Hey quick question how did you drop that black bar on the left side of the motor? Mine won't budge at all.

[@eliesehunt804]

why you never came back

[@albertsln]

Thank you so much brother great video and info 💪💪💪💪💪

[@mikedarden4357]

Make sure the coolant system is bled and change the cap. Happened to me. No problem since

[@miguelmkp6239]

at what temperature does the thermostat open, and how many pounds is the radiator cap? i have had problems with my buick?

[@jamesdean1598]

195F

[@bishopmills4263]

Why did your thermostat keep failing? did you use an OEM Ac Delco thermostat? Did you test the old thermostat in a pot of boiling water? So many questions - thank you if you answer.

[@jaredtgriffinatyahoo]

Bishop Mills my question exactly

[@438marcus]

Because he puts a gasket on the thermostat 😂

[@zacharyfreeman3201]

also be very careful not to slice your hand open on the intake port like I did yesterday 14 stitches later I got my thermostat on

[@garylangley4502]

Zach! Been there, done that, didn't like it. An automatic transmission slid off of the jack I was using to lift it and hit me in the forehead. They used staples on that one.

[@jasonrobbins4227]

Liquid stitches known as super glue my guy. I just use painters tape lol

[@fondfarewell2]

my 2001 century has the same issue, it's overheating after only minutes of driving, wants to go straight to 3/4 temp, and my heater does not work, and all coolant likes to go into resivoir. replaced the water pump about 5 months ago, and all was fine till recent, was ready to replace the radiator but I think I will go with the thermostat first.

[@byloecelhigh8467]

My cars engine gets extremely hot to the touch almost scalding, but the temp gauge needle stays at the middle or right under the middle. The issue I’m having is that the low coolant sign is on but the radiator reservoir is full. Anyone have any idea what could cause the light to turn on. It happens after driving for 1 hr.

[@quixotic317]

Replace the low coolant level sensor. It's near the radiator on the battery side.

[@garylangley4502]

Thanks for your help. I have 3 kids in college, and I need to save anyway I can. I bought a more expensive thermostat, so hopefully it will last longer. This thermostat will jam open if it goes bad so the engine won't overheat. The old type stay shut.

[@CBlazeSiccxMpls]

This is a good video but he doesn't tell u how the bottom bolt is going to need a small 1/2 wrench. I did mine today shit took to long but it's a very tight space your working with so cant blame it for that but could have added that to the video just a thought!!

[@CBlazeSiccxMpls]

And when I say small I mean half the size of a regular wrench try and 1/2 or 13mm works to .. Be patient because it takes time so dont get mad I wanted to smash my shit but kept my Cool Haha

[@darknight52cat]

I cut my 13mm wrench in half for that exact reason

[@davidr5515]

I have the same motor but can't get to that lower bolt holding the housing for Thermostat. I even took off the top plate over the exhaust to get another 1/4 inch. How did he get it off? - Thanks for sharing this vid

[@jennagraciliano6156]

OMG that's where I am stuck right now I been cussing n throwing tools for 40 damn mins my dad use to help me with all this he died in January I just said damn it dad what do I do .... N found this comment thank you

[@tyler2610]

Chances are if it looked like it was seeping coolant and it's overheating your lower intake manifolds were leaking and you were getting low on coolant.

[@americanguy1317]

No his problem was the so called gasket he made, the only gasket that is used is the rubber one attached to the thermostat what a dufus

[@nothingburger7072]

What happened to part 2? Taking that long to put another one back in?

[@CBlazeSiccxMpls]

Nothingburger that shit ain't easy id of skipped it to just did one in my car ain't that bottom bolt sucks half turns all you going to get!!!

[@niktooXD]

ive been tuned in for 5 years waiting for this break to end... wheres the other part?!?

[@michaelspeakman8924]

If it's a newer Buick it should have a rubber gasket around the thermostat. Which you don't need a gasket any longer.

[@rhondanelson2669]

Should change a/c thermostat at same time. Don't for get to bleed your coolant valves. You can tell if your thermostat is bad by dropping it into a pot of boiling water and it should open if not its bad.

[@cubehire3653]

Interesting this video is listed in the Comedy Category. I noticed that many of the steps needed to perform this replacement were done before the video started. That's when I bailed. Thanks anyway.

[@stevewinter8928]

When you make a video do all the steps, don't say this is the hardest part and then skip over it And it looks like you were skipping over a lot of other things too so it would show the things and more people would be like it

[@sc2till]

Best advice yet thank you very

[@jennagraciliano6156]

Did you ever do a waterpump video sir this video was very helpful

[@britanyhunter9486]

How do u change the filter ?

[@britanyhunter9486]

Never mind found a video to change a the filter to a 2000 Buick Century

[@noeljr800]

He should've showed the whole process.

[@damon9408]

The bolt is a 13mm, home slice. It is possible to do it without taking of the throttle body. It's a bitch, but it can be done.

[@monotv1808]

Was it the thermostat??

[@DavidMiller-do9gg]

truth is , who ever engineered this car (which i own) should be continuously bitched slapped for the rest of their lives. GM Smh If anything was ever engineered back ass wards it was probably done by the extremely well paid people at GM.

[@southpaw8040]

+David Miller If you think this is bad, try working on a Volkswagon or any other German car. They are a nightmare to work on. You typically have to spend 20 min taking out plastic panels and clips before you can even access the part. Not to mention all of the special tools you need. ie. torx bits, hex bits etc

[@DigitalBridge.]

Amen Brother! LOL.

[@kazilziya830]

You are so right about that brother. Smdh

[@pubicnozzle9775]

You know it’s bad when changing the battery requires removing the strut brace

[@gregoryjones483]

Thanks for the video. It took me a while to find this. Car running hot and no pressure on either of the radiator hoses. Whats up? I got a thermostat but have not attempted to install it yet.

[@kalebreinhart]

You've got a great personality. Stay awesome

[@blessedjuggernaut]

This is why I'm glad I own a 2011 Ford Crown Victoria Police Interceptor instead of a GM or Chrysler turd

[@debbiebeeman8863]

I need the location of the heater and air blower

[@fun1brians]

Thanks for the video, now I will remove the throttle body to get to the bottom screw. New subscriber Brian, thanks again and keep up the good videos!

[@dreadentity_tin]

Thank you for your first video, it was very helpful. Is there a part 2 to this video? Also, if it's not in the second video, is there a video on how to remove the throttle body?

[@chewilliams9731]

Yes, kzbin.info/www/bejne/p3nEc6Zsq9ONhrM

[@laro747]

REALLY COM ON NOW U REALLY TOLD US YOU DIDN'T SHOW US.

[@silasdunn5801]

great video I need video of how to get all that shit out of the way

[@lizbishop2597]

would you come and change mine?

[@jesselamb7788]

I watch the guy pulling engine in less than 40 minutes the other day on KZbin

[@fishbone856]

GM hasnt used sae BOLTS since the 70s and there is no gasket for this job

[@chewilliams9731]

It wasn't required but, it was something he suggested even though the thermostat itself had a seal on it.

[@yahyahtaza-daqhayah7104]

Great video I just ignore the ignorance of the comments.

[@damon9408]

There is no gasket.

[@chewilliams9731]

The gasket was an option that we decided to install onto to the thermostat housing.

[@214greedy167]

Ché Williams make more videos bruh

[@djstoryt]

Thx it's very informative

[@102Help]

"dis is uh 2000 uh Burick*

[@derrellpill2932]

Car become alot of work ,l see why shop will clean you out. I've helped friends on cars ,you will be sore the next day. SCARED HANDS. MINE is stuck open.

[@marlonbutler7434]

Just stop talking so much do the work

[@jhoodied4861]

I can't see shit with that wack ass phone camara, but thanks anyways.

[@tomkeuffer7407]

Guessatech

[@levibyler5830]

or just slat the interference my car has a mind of its own

[@djh8950]

please rotate your phone next time

[@Stonereraldi]

"Buckwheat say you don't have to take off the throttle body!!! "Not to cool you don't know the difference between a nut and bolt or a Screws!!! Those things in your hand are called bolts not screws!!! Now Because you don't know that you have a bolts in your hand you should put down the tools a step away from the vehicle please!!! can avoid running into these kind of problems is by Inspecting #1 Thermostat rotator joint axle pin #2 The clamps holding the bearing retainer valve in place! Inspect the bolts if they pop off it will damage every thing around it!!! Very important!!!. #3 The 3.7psi of torque to the heli coil sensor inverter hose and fittings!!! Have this torqued every other oil change. will give you faster startups! This takes one minute to do and always over looked 90% of the time!!! So remind the mechanic that's running around like a rooster with out a pecker 95% of the time so you can see were i'm coming from and why things sometimes get over looked!!! Give the dude a little slack!!! These little stupid tips can save you a expensive tow bill. I believe in taking maintenance serious on all my vehicles! Hope this helped!!! It just might be smart thing to highlight this and print my comments out. This can help you bring these things to your mechanic attention!!! Ask him to make it his business to check these things out so you can trust your vehicle. Plus feels great to knowing your car or truck up to date!!! "You belong in your suit.

[@mjones2431]

Stone Rinaldi do a google search for hex head cap screw and tell me what you come up with.

[@fishbone856]

LMAO!