Shift problems can be complicated or quite easy to fix depending on what was damaged. In this video we find the fixing the problem to be simple and I will walk you through the proses of finding the problem and fixing the issue.
Пікірлер: 42
@radioace318la2 жыл бұрын
you got lucky. the plate your part is moving is what broke on mine. You can not replace it without pulling both clutches. I did mine in the frame. If I had it to do again, I would pull the engine out. it was a PITA to do it in the frame. Cheers from Louisiana.
@gregdavis8562 Жыл бұрын
What kind of threads on the 2 clutches,
@libtardismtruth9315 Жыл бұрын
Just had the same issue on my 2002 honda 350 rancher Trx ES 4x4, easy fix thank's for the video
@grahamsmith49885 жыл бұрын
Brilliant, I have the same issue and you saved me hours! Thanks.
@MegaMIIKKEE6 жыл бұрын
Great video man thank you so much! Same exact problem with mine!
@esybra736 жыл бұрын
Thank you so Much i had the exact same problem!
@MrFixit16 жыл бұрын
I'm glad I could help you are welcome
@ryanmichaels42263 жыл бұрын
Very very helpful
@markchamorro84095 жыл бұрын
Thank you so much for this video. Very knowledgeable. One question, is the clutch adjustment the same for a 2000 Rancher ES? If I use the emergency shifter, I could copy your method. I assume I can, but just wanted to make sure
@pl7475 жыл бұрын
So if you have a lot of up and down loose slack on the foot shifter that needs to be adjusted? It looked like there should be very little up and down looseness at the front end of the foot shifter.
@joshuabyers98394 жыл бұрын
Mr. Fixit I had an '06 Honda 350trxtm ( left peddal shifter) , we'll I blew a hole in it. I bought a '05 350trxte didn't realize it was electric shift can you please help me in converting it
@allensharlow57045 жыл бұрын
Anyone know how to remove the old wheel bearings and seal on the rear brake hub side of a 2001 Honda rancher 4x4??? Please help
@rodtwichi12903 жыл бұрын
I just bought an 02 rancher 350fm it shifts super rough when shifting up but down shifting is fine. I noticed the clutch adjustment but was loose and readjust that and tightened tho it helped it still shifts up the gears rough. More so into 2nd and 3rd unless at a high rpm. Please help
@MrFixit13 жыл бұрын
Strange that it only does that up shifting. I can only assume what you mean by shifting rough. A better explanation of what you mean may help in diagnosis. Only two things come to mind. Bad shift drum or bad clutch. I would disassemble the clutch basket and check the clutch plates. Look for warped steals. Does it shift rough when the engine is off? If so it may be the shift drum or shift fork.
@littleredridinghood56223 жыл бұрын
The spring and roller cage go down , not up towards the clutch cover ..
@dallastrost6872 жыл бұрын
Which part of clutch needs replaced if just idling while in gear downhill it will free roll? If I Rev engine it catches and slows the bike but once it goes back to idle it starts free rolling again. Any help is appreciated.
@MrFixit12 жыл бұрын
Sounds like the one way roller sprag.
@justinbrown69434 жыл бұрын
What is the name of the part that was broke?
@jonbovi21833 жыл бұрын
I have a 02 rancher 350FM and I just put a new centrifugal clutch basket on it and still have same issue which is in all five gears when you mash the throttle the wheels wont spin at all. Please help
@MrFixit13 жыл бұрын
There is a 1 way bearing or Spragg clutch in the auto clutch drum if you put that in upside down that would cause this issue. or you have the play adjuster turned in too far. There may be a few other things but I would start there.
@infinitelyawesome38852 жыл бұрын
What kind of sealant is that you use on the case. Rtv or anaerobic?
@MrFixit12 жыл бұрын
I used the Anaerobic sealant.
@Miner417 Жыл бұрын
Hey do you know what would cause it to shift but not move. I can shift through all the gears but it won't move even when I fev the engine.
@MrFixit1 Жыл бұрын
Could be the centrifugal clutch one way bearing, or the play adjuster is adjusted in too far, or the clutch is bad.
@jeremytalcott41612 жыл бұрын
Can you weld the broken part?can this repair be made in the quad?
@MrFixit12 жыл бұрын
Yeah, I'm sure you could weld it. It may lose its hardness. I don't think this job can be done in the frame unless you remove some stuff. but I have never tried.
@jeremytalcott41612 жыл бұрын
@@MrFixit1 thanks For the response I pulled the motor last night
@estebanmorales64211 ай бұрын
Nice video how mucho did y pay for it
@norfolk19363 жыл бұрын
A very good heart surgery .....
@MegaMIIKKEE6 жыл бұрын
Hey I have a question would u know for any reason my spring popped off twice when I did it could I have had it backwards ? I put it back and i tried it twice and it shifted so I left it alone
@MrFixit16 жыл бұрын
That's a good question with many answers, and assuming you are talking about the shift return spring, a few things come to mind. Spring loosing it's tension or the groves that retain the spring warn. I'm not sure installing it backwards will have any affect. The spring should be seated all the way down onto the shaft and pinching the tab connected on the lever attached to the shift drum. The job of this return spring is to return the shift lever back to center position after a gear change. I hope this helps and other with more knowledge may also have info on this subject. Thanks for your comment.
@MegaMIIKKEE6 жыл бұрын
Joshua .Brown np I put mine back together and it says it’s in neutral but when I shift it to first it makes the sound like its shifting but - comes up on the gear indicator and it rolls like it’s in neutral but I can shift it back to neutral it just won’t go into a gear
@MrFixit16 жыл бұрын
check the play adjuster if this isn't adjusted right in will act like it is in neutral when it is in gear. Adjusted to far out will apply pressure to the clutch pack as if you was squeezing a clutch lever on the handle bars. I hope this helps
@MegaMIIKKEE6 жыл бұрын
Joshua .Brown yeah it’s wierd I don’t know if I adjusted it right but when it’s neutral if I pull the cord a tiny bit it will go into gear or if I move the bike.
@MrFixit16 жыл бұрын
try adjusting the play screw all the way the other way and see if it makes a difference
@Cromwell648 Жыл бұрын
Top tip, when speaking, turn the air compressor off!