Great video, all meat and potatoes. I hate when they want to give you a whole backstory about how thier uncle Billy Bob bought it from thier second cousin cause thier wife was having a kid and you get my point. I like your style, right to the point.👍
@jcortiz1112 жыл бұрын
I have the same symptoms in a kawasaki bayou 250, now I know which part I should replace, thanks for the video. Have a nice day.
@shrop9 ай бұрын
Thank you! This is what I needed to see.
@noahpriess6624 жыл бұрын
Would this baring cause my 420 to grab to fast and like jump forwards when shifting to first from neutral? I tried to adjust it but couldn’t get it to stop jumping.
@tysonfoulger97073 жыл бұрын
No. Try adjusting the set throttle on the carb
@nickkgalderese3 жыл бұрын
If my 1 way bearing is backwards would it cause my bike not to shift into r,n, 3, 4, 5 ????
@garywilson95333 жыл бұрын
The drum look pretty grooved like mine. When should I replace?
@jaredmckenzie78212 жыл бұрын
This is the exact thing that mine needs but it also shifts very rough is their something that could be causing that
@thomassylvestro90413 жыл бұрын
Thanks for video. Any thoughts on a 03 TRX250ex not moving once in gear
@nathanscott40492 жыл бұрын
My foreman when going down a hill it will free spin then clunk the motor catches n the motor revs up is that bearing the cause
@KY87Chevy4 жыл бұрын
I have a 1985 big red and when I try to kickstart it it won't catch. Is this the bearing that could be the problem?
@1kjared6143 жыл бұрын
yes
@karlosvyss4 жыл бұрын
is it recommended to change the clutch pads whilst doing the one way bearing??
@squarecrawler95516 жыл бұрын
I’m getting kinda a clunk/ snap out of mine when it’s cold. Sounds like it’s coming from the centrifugal but haven’t experienced any other symptoms. It goes away once the motor is completely warmed up. Any ideas? I’m thinking possibly could be this bearing? Thanks for any input!
@RBoysMedia3 жыл бұрын
Lol 2 years late but yes this will be the issue
@bobbymckinney12644 жыл бұрын
Would this cause the motor not to turn over when kicking it..cant get the kicker to turn the motor,the kicker is in rite
@Solitude3134 жыл бұрын
Yes it for sure would.
@trevorglenny22274 жыл бұрын
My clutch is spilling going form 4 to 5 if I adjust it would it fix the problem or do I need a new clutch??
@maplelagoo90015 жыл бұрын
Is that the part number for a 1986 trx350?
@liammcgee36375 жыл бұрын
Hi , my centrifugal clutch is the sma eas this but at the rear of mine the springs I think they are seem loose . They are built into the drum so I cant access them . One is like a yellow colour and doesnt move . Does this sound right , the rest make a slight rattle when rotated
@savagestealth53386 жыл бұрын
Would this cause the clutch to slip as well just replaced clutch in honda recon both of them and it does free spin but would it also cause the slipping as well
@Solitude3136 жыл бұрын
No, the Clutch Discs are what causes it to slip. This is just for engine braking.
@KY87Chevy4 жыл бұрын
@@Solitude313 I have a 1985 big red and when I try to kickstart it it won't catch. Could this bearing be the problem?
@Jaylan_T3 жыл бұрын
how long can you ride with a bad one way bearing ?
@garywilson95333 жыл бұрын
For as long as you want. It will spin after you shut it off, won’t slow down while down shifting, and you can’t pull start it.
@Joshjoshnbvj Жыл бұрын
@@garywilson9533so riding it with a bad one way bearing won’t cause any harm?
@andrewmcdougal50513 жыл бұрын
I have a 300ex and it won’t start it turns the motor over a little than free spins has a new starter is this what I need to change ?
@keithsutcliffe46352 жыл бұрын
Do you know if they start squeaking before they go bad
@done65385 жыл бұрын
Good video. My 2005 trx500 foreman won't shift out of reverse when cold unless you yank up on the foot lever until it's at operating temperature. Then it is fine. Could that be the problem.
@Solitude3135 жыл бұрын
Do you have the choke on at that time when it hard to do?
@luxstar4life Жыл бұрын
Can this cause a little clunk noise when running?
@Brobro4496 ай бұрын
How do you know when the one way bearing is bad?
@kylelanders8457 ай бұрын
On my 250ex would mine being backwards cause it to jerk and stall when going into gear almost like riding a bike with a clutch but it’s not soposed to need a clutch lol
@grantbro81335 жыл бұрын
Would the one way baring cause the starter to spin but not turn the bike over?
@blazersatving29414 жыл бұрын
old post but thats happen to me with my starter was the bearing your issue
@josephmarcell62242 жыл бұрын
And another year later but same thing here!
@Fl_bluecollar6 жыл бұрын
Thanks man! This helped a bunch. The FSM lacks a diagram of this. They explain it, but don’t show it. Quick question though, I replaced the cam chain on my 98 fourtrax 300, put the side cover back on and the kick start seems like it just spins, doesn’t feel like it catches the engine, would a bad one way beating cause that as well?
@Solitude3136 жыл бұрын
Yea, that is another sign of this issue with the Kick Start.
@Fl_bluecollar6 жыл бұрын
SolitudeCustoms that’s what I had thought, I’ll just replace it when I pull the engine to rebuild the top end. On a 2wd version I should be able to pull the engine without pulling the rear tires and plastics off, right?
@Solitude3136 жыл бұрын
I would think so, plenty of room to move forward.
@Fl_bluecollar6 жыл бұрын
SolitudeCustoms thanks, I’ll let you know how it turns out
@kawiryder63914 жыл бұрын
Can i keep riding it since i dont have money to replace it since cuz of this virus crap
@masongreen18715 жыл бұрын
What year is part number for
@dylanmclain62872 жыл бұрын
I have a 17 model 500 rubicon, and it's very hard to shift gears and I do have a starter issue too. I've never worked on a Honda so could anyone help with that?
@johncraft253910 ай бұрын
Will this cause slipping and clunking
@coltonlynn28252 ай бұрын
Clunking yeah, slippings from the fibers on the weights being worn
@rzr8hunnid5176 жыл бұрын
How much do these cost and where can you get them
@Solitude3136 жыл бұрын
Honda Cruiser This was OEM, about $80
@AngryRanger4.02 жыл бұрын
On my 300 when decelerating there is a grinding noise could it be from a one way bearing? The noise sounds like a bad bearing everything else is fine except when slowing down. Any ideas?
@masoncorbitt15082 жыл бұрын
Is the noise around the drive shaft in the front?
@projecta316 жыл бұрын
im trying to diagnose a fault with my honda300. The motor runs fine idles and revs perfect. I can select gears fine. but the drive will not go to the gearbox. I cannot kickstart the motor. but with a gear selected i can drive the wheels with the kickstart. Any advice on where to start?
@fortteen26366 жыл бұрын
projects adjust the clutch pack download a service manual.