2003-2007 Honda Accord Door panel removal

2006 Honda Accord Plastic door panel removal. You want to remove this piece in case you want to replace the window, window motor, or the power switch harness.
Tools:
amzn.to/2bdCm1Y Plastic pry bar
amzn.to/2awcdGr Phillip screw driver
Parts:
None
Torque specs:
Hand tighten
like and share this video!
If you have any questions or concerns, feel free to leave comments on our FB page.
Like us on Facebook
bit.ly/nutzaboutbolts1
and SUBSCRIBE!
bit.ly/NutzAboutBolts2
Intro: RavenProDesign
www.RavenProDesign.com
Music: Manic Bloom - Death and Conversation
/ manicbloom

[@emsjane23]

This video saved me $250!! Thank you so much for posting! I was able to fix my window with no broken pieces and minimal cursing!

[@cwilson1028]

🤣🤣🤣

[@nadirboutella4171]

Wait what was wrong with your window did you had to glue it back? IF SO let me know what you used I'm planning on doing that today

[@tonezchannel1711]

I did this nothing worked window still will not roll up

[@cre8tadream]

For the 2004 Honda Accord EX Coupe (2 Door): Rather than one screw in the armrest underneath a rubber mat, you will find two screws facing in towards the door underneath (towards the bottom) of the armrest.

[@noahwalter4964]

Goat 🐐

[@losxlakers]

The last thing you said was reset the power switch, what's that and how do you do that? I'm so glad you're back. I have a 2004 Honda Accord and it needs a lot of work. I was pretty worried when your channel was down. You guys are awesome! You guys are very detailed and explain things very well. You guys have the right tools too. Thanks guys.

[@NutzAboutBolts]

you want to put the driver side window down all the way, then press and hold for 5 seconds. After that, you bring the window all the way up, then press and hold up for 5 seconds. That's how you reset the auto window up and down for the driver side.

[@darrellblair5818]

Fantastic video. Exactly what I needed to see. Thanks.

[@dannygonzales2514]

Fixed my friends car with this video! Thanks bud!

[@cronoodle]

I used this video to fix my window that fell off the track. It was very helpful. Thank you!

[@NutzAboutBolts]

np!

[@deebsmigs]

How do you remove the wire thing for the window switches? Mine seems stubborn. The side view mirror one was easy to disconnect.

[@bigrob9759]

is this also applicable for acura tl 04 - 08?

[@joshuagerloff4065]

Is there anything different I need to do for my 2001 Accord? Also, how I can i tell if its the windows motor or a blown fuse? just wondering Im new when it comes to cars so help would be appreciated

[@the1964gman]

Thanks! I had to replace the window regulator on 2004 Honda Accord and when I put it all back together for some reason the inside door handles would not work. After watching your video I see my mistake. Thanks for posting.

[@NutzAboutBolts]

nice!

[@fenekilll]

Thanks dude, I hope this works for my 04 tsx

[@Yoolsin]

THANK YOU! My window had come off it's track and I was able to fix it myself!

[@NutzAboutBolts]

Nice!

[@tehxii7706]

Any speaker recommendations that plug in and fit? I suppose you'd have to replace them all to make a difference.

[@truejey7475]

Do you know what kind of glue adhesive can i use to seal my door with that plastic cover? I have water coming in to my passenger footwell when it rains.Thanks a lot bro

[@chris-samuel-cesar]

Hey wut up what if one of the plastic break on me can it be replace let me know thanks

[@Octopopsv_]

Thank you for the help. You're a life saver

[@paulhumpal8015]

Thank you for this video. It has helped me a lot. A super demonstration.

[@killtheidols1326]

Thank you man,,,,hi from Spain,,,

[@ericsonchagas]

Congratulations for the video, I know it was a long time ago, but it is been useful for me now. Do you know what black gooey stuff is this at the white plastic cover? Cause I'll need replace mine dirty one. Thanks.!

[@diablo1271]

Thank you so much for This video. It was very helpful😊

[@schmigr]

Good video on how to remove door panel to enable access to a variety of components and fasteners. I used it to lower the panel to ease access to the bolts holding in the side view mirror. I didn't have to remove the panel entirely, thus eliminating the need to detach the control console on the armrest or the cable to the door latch.

[@georgiaguardian4696]

Thank you for making the video Very useful1

[@matthewclements7842]

Just picked up an 07 accord with a loose window. Exactly what I needed to know. Thanks man!

[@squirrelattackspidy]

Great video dude! Is it hard to get the motor out if it needs to be replaced? If the window stopped half way up, is it likely that the motor is okay but the window is stuck on the track or out of alignment?

[@user-or5wh8um6z]

Thank you man you really helped me 👍

[@arieagung]

I have same problem with the same window, is it kind of factory defect?

[@stevenarellano1988]

Are both two door and four door the same size??

[@tudorsor91]

how to replace the turning lights in the mirror? i have an 2004 honda accord euro model

[@GAGE1959]

Awesome job sir ! You make it so easy to understand the process !

[@deborahmartyn97]

so helpful, thanks.. shall be tackling malfunctioning window soon

[@karleejenkins4852]

What if one of those button clips won’t come out ? Have tried everything can’t get it to come out

[@user-yc2oz8kc5k]

My door handle cable seems to have snapped so now I know how to remove the panel to replace it. Very nice

[@jaredmiller2128]

I learned the hard way that if you remove the panel as demonstrated here, the green plastic holder on the door cable will almost always break. If you remove the door handle before removing the door panel, you can avoid breaking the plastic piece. I'll be opening my door from the outside until my new cable arrives. I'm sure 8 years ago the plastic on this guy's car was still pliable enough that he could get away with this. Not so much now.

[@cgrscott]

Thanks. I'm accessing the inside of the door and removing the sliding window glass to get the lock cylinder out to re-key the door lock. I have successfully done it with my 2003 Honda Civic and it looks like the process on the 2005 Accord will be similar. Removing the cover panels off he Accord door is a little different than with the Civic. Your video is very helpful.

[@NutzAboutBolts]

glad we could help :)

[@cgrscott]

I did not have remove the window glass after all before I attempted to.

[@NutzAboutBolts]

usually you don't need to remove the window glass when removing door parts...

[@thomaswooden3]

I have a 2006 honda accord the driver side door window goes up and down, but none of the other windows work, so I'm thinking the motor is ok, what would your recommend I check next?

[@NutzAboutBolts]

does the master switch works when using on the driver side? does the window go up when you use it on their individual sides?

[@Truth_Seeker407]

Google it. I found the fix. U bridge two wires under the window switches

[@danfuerthgillis4483]

Lmfao my Accord 2008 coupe window was getting stuck on the top rubber today it fell in. 15 minutes later was up and running with your video lol. Also found out someone already changed the glass and did a poor job at the installation , also the glue was gone on the plastic track and lol there was no grease on the up down track lmfao. Excellent video!!

[@terrythepion6181]

What is the name of that plastic bag looking piece and where can I find it

[@bIgbossdornel1574]

QUESTION !!!!!!!!!! when I roll my 2 front mirrors up/down they make a squeaky sound, any idea what part might be going bad or rubbing against it to cause that sound ?

[@NutzAboutBolts]

could be the weather strip for the glass is worn. Try using silicone spray on the rubber part and see if the noise goes away. It's probably old and brittle so they are dry and cause noise when rolling the glass window up and down.

[@yardlimit8695]

good vid............thanks,,,,,,short and to the point without a lot of wasted words and useless jibber jabber..........thanks again.

[@krzysiekpawlak6992]

Thanks, mate. I have a problem with the lock and I'm trying to fix it myself. Thanks to you, I know how to remove the door panel 😁

[@NutzAboutBolts]

No problem! I also made a video on how to replace the door lock actuator.

[@krzysiekpawlak6992]

​@@NutzAboutBoltsCan you provide a link to the video?

[@NutzAboutBolts]

@@krzysiekpawlak6992 here you go kzbin.info/www/bejne/r2W0lqebaNN1m9Esi=_Lt3RanZFjP7h2of It’s for the passenger side, but it’s the same concept for the driver side, just different part used for the actuator, instead of the passenger side actuator, you’ll need the driver side actuator for the driver side door. I hope that helps.

[@krzysiekpawlak6992]

​@@NutzAboutBoltsWell, now I know what it's about. Will a new actuator be needed or will regeneration be enough?

[@NutzAboutBolts]

@@krzysiekpawlak6992 if the door doesn’t unlock or lock, you’ll need a new one. Not sure about regeneration. Never heard of it.

[@johncasoni4379]

2006 Honda Accord EX Coupe door panel is different. I have locked door and no idea how to get panel off. Right now there are 2 screws in the bottom of arm rest, under electronic window switch, which are a problem to get out, but when those are out, still don't know if panel will come off.

[@boxofgreens698]

Thanks for the help

[@robertd.7101]

It is strongly suggested to disconnect the battery when working on your car. even something simple as unplugging switches.

[@archivaldo4310]

Really shit I never thought of that I didn't think it hurt anything

[@terryscott1950]

Great video thank you so much!

[@NutzAboutBolts]

Thank you

[@TheJonwashington1]

I checked the 20 amp fuse and it's good. What do I check for now?

[@NutzAboutBolts]

+Jonathan Washington could be a faulty driver's power window motor or an open in the wire.

[@jeffreycontreras6150]

Nice job 👍

[@Chumpers001]

What size wrench do I need? My 2004 Accord power window motor is giving me trouble.

[@NutzAboutBolts]

Jeremy Baloun I believe we did a video for that on the 2002 accord. Should be the same size as that.

[@joeslacy]

Can you do this same procedure with the door closed and not able to open?

[@NutzAboutBolts]

no because you need to take off the plastic door panel.

[@burgerking220]

I got hit my passenger fender and this caused the window to stop working. It will go down very slowly and make some scratching noises. Do you have any idea of what might be the problem? Or what I can do? I would really appreciate any help.

[@NutzAboutBolts]

could be a wire harness problem if the wire is routed through the fenders.

[@TinaCalifa]

Thank You !!

[@Fuzznuv]

hey man! Can y'all please do a vid on how to change the front wheel hub assembly on an 03-07 accord 4cyl please?? I need that bad!

[@NutzAboutBolts]

+Jordan johnson are you talking about the front hub? its pressed in on the wheel bearing, we can't do the video since we don't have a press.

[@companrene8348]

Muchas gracias

[@TheoneandonlyLadyLiz]

awesome and helpful

[@NutzAboutBolts]

glad we could help

[@fatboy12G]

How do you reset your power switch?

[@celerosario6228]

Gracias por compartir.

[@amit666715]

I have an issue with my 2004 Acura MDX ,when I unlock the door with the remote or key get inside and start it all the doors automatically lock ,the problem is if I unlock it and leave the car soon as the doors close it locks again with the key still in ..what might be the issue?

[@NutzAboutBolts]

probably something with the programming of the key door locks. I would ask the dealership if they can reprogram it for you or something.

[@wussawp-csgochannel5872]

Voice of toby from the office

[@c5scottman]

8

[@thc2thefacejp844]

hey , I appreciate the help u gave me last week . i have a 98 corolla le with overdrive . It's idle is lower than Normal and acceleration is sorta sluggish . I need your master mechanics skills !! Lol please and thank you

[@NutzAboutBolts]

+Justin Platon any check engine light?

[@thc2thefacejp844]

+NutzAboutBolts yes , the check engine is on . speed sensor is bad . i took that off , error code registered trans speed sensor. even cleaned my throttle body some what. any idea ?

[@NutzAboutBolts]

Justin Platon you want to fix all your check engine light code and then recheck your car, other than that, you can't do much besides fixing the codes first.

[@thc2thefacejp844]

+NutzAboutBolts okay I'll recheck auto zone and see the codes again. I can do a video of my car as well. not sure if u have time

[@TheJonwashington1]

I have a 2004 Honda Accord Lx coupe. My driver side window stopped working a few days ago. I checked the master window switch on the driver's side, it will let down the passenger's window down, but not the drivers window. I replaced the master switch and it still doesn't work. I don't know what's going on. Can you help, please?

[@NutzAboutBolts]

+Jonathan Washington Did you check the 20 Amp fuse under the kick panel??

[@iamstephaniepouliot]

I have an Accord DX without power mirrors, so I can't merely "pop out" the triangle shaped trim piece in the upper corner of the door, because there's an lever attached to that piece to adjust my side mirror. Any ideas on how to get this piece off with the lever attached? I've tried pulling and prying it off, but it won't budge and I don't want to break it.

[@NutzAboutBolts]

it could be twisted on or screwed on... not too sure, do you have a picture?

[@iamstephaniepouliot]

I'm not sure how to post a picture here, but you can find a pic of the driver's side door easily by doing a Google image search of a 2004 Honda Accord DX.

[@NutzAboutBolts]

I tried to google it and still don't see it. You can go to our FB page and send us a message with a picture of the part. Front and back please, thanks!

[@thecarexpert21]

I've noticed, a recent issue on our 2006 Accord, is when you lock or unlock the doors, you'll hear this screeching noise coming from inside the door panel. Any ideas on what it could be? Doors lock and un lock fine still.

[@NutzAboutBolts]

+thecarexpert21 I would still remove the door panel to inspect the noise, everything is there for you to see. So you can mess around and see where's the noise is coming from.

[@landshass2849]

I had the same noise in my 2006 Accord. I ignored it for years and nothing wrong happened.

[@12345brick1]

the one thing that i needed to learn was already done. the cable to the door handle was already disconnected

[@scientist100]

It is hard to get but the first safe thing to do is pull the handle out (there is always play) and get a regular size flat driver and pry the plastic holding it and then pull it up to disconnect it.

[@twonice4u]

Could you show how to remove the front bumper of a 2006 Honda Accord. Also what size are the clips for the front bumper. (I'm missing some) Thanks, loving the videos.

[@NutzAboutBolts]

+twonice4u We'll add it to our list, we'll have to find a day to be available to film...

[@killtheidols1326]

Big like bro,,,,

[@SashaNem]

thank you

[@poolnoodle5412]

My window just makes a grinding noise and won’t roll up at all is it off track??

[@NutzAboutBolts]

I’d open the panel and check if the window glass is bolted on the rail track. It’s pretty simple to do.

[@ShowMMaker]

Nice, works

[@kvang254]

Thanks for the video. I was having issues with my keyless entry and figured I'd take the door panel off and take a look at the switches.

[@NutzAboutBolts]

no problem :)

[@enexsix]

You don't have to remove the door panel to check the keyless entry switches. The unlocking receiver is part of the master power window switch unit (the one he removes from the door panel to take the wiring connectors out the bottom at the beginning). The cable goes back to the dash after that. If your receiver has gone bad, you can replace it in five minutes (it comes as part of a new switch unit). Not to be daft, but have you tried replacing the battery in your keyfob first?

[@kvang254]

enex six yeah I've checked the battery in the keyfob. Well just an update, I had a few plans to fix the keyless entry. Started off with the keyless programming and it fixed the issue. Lock, unlock, trunk, and panic all work just fine now

[@cyndifoore7743]

Great channel. You remind me a little if the asian guy on Dexter, your profile and mannerisms, not your language. Peace

[@zero9112]

"Now you're dealing with science and science is one cold-hearted bitch with a fourteen inch strap-on."

[@aqui7817]

Thank you so much for this video.

[@chadcuckproducer1037]

Thank you.

[@hondaaccord2425]

Pull harder 💪

[@hieppham7435]

Thank you

[@NutzAboutBolts]

+Hiep Pham glad to help :)

[@leroycharles9751]

Thanks.

[@TheJonwashington1]

where is the fuse located under the kick panel?

[@NutzAboutBolts]

+Jonathan Washington it's on the left side where you step on the gas pedals. There's a plastic cover you remove and there will be fuses behind there

[@yaboydryp]

Does this apply to the 06 Acura TSX?

[@NutzAboutBolts]

Yes, should be the same

[@pochologabriel7404]

hey do you have any video for the rear door driver side?

[@NutzAboutBolts]

not as of right now... whats wrong with yours?

[@pochologabriel7404]

+NutzAboutBolts oh i think the door latch might been disconnected? i cant open the door from. the inside

[@NutzAboutBolts]

oh... I see, its the same procedure as removing the front door panel.

[@pochologabriel7404]

+NutzAboutBolts ok sir thanks im gonna try opening it.. hey bybtge way do you have any idea how to replace evap on the accord? i got cel and pulled out the codes its a evap leak

[@NutzAboutBolts]

Evap canister is on the engine compartment starting from the driver side down to the rear of it... evap leak can be around any of that place... gotta see where the leak is coming from first.

[@ewallacestudent1]

doing speakers tomorrow thanks for the visual.

[@santanam5718]

So i have a 2006 honda accord, but have 2005 honda accord interior.. will it fit?? Someone help.

[@padelmar]

How do you remove the front passenger's door panel? It is different to the driver's

[@NutzAboutBolts]

hrm, we'll have to film it, its a lot easier than the driver side

[@Spex805]

padelmar Its the same just without the master switch.

[@proshredda91]

Look UNDERNEATH the arm panel. Up above the storage area in the door I found two screws.

[@kasjamm]

I'm having trouble putting the panel back on. Nothing will line up...

[@NutzAboutBolts]

kasjamm you want to line up the top first, where the window seal is at, it should sit on it before you start snapping the rest of the panel up.

[@kasjamm]

@@NutzAboutBolts Thanks! I got it.

[@kuroshitsui1292]

can you make a video for the oil pump gasket?

[@NutzAboutBolts]

+Kuroshi Tsui there's no oil pump gasket, the oil pump is in the oil pan held on by bolts... there is no gasket to be replaced.

[@kuroshitsui1292]

+NutzAboutBolts Damn Lol, I'm new to cars unfortunately proud 7th gen accord owner but I've been having an oil leak...last time I had one was last year In December it was the vtec solenoid gasket I replaced it and it ran no problem until a couple of weeks ago. leaking oil again but I can't find where..seems like its under the steering wheel pump by the tensioner. you know anything by any chance?

[@NutzAboutBolts]

Kuroshi Tsui I would say put in some oil dye or dye in general and use a black light to find the leak. You can buy the kit at an auto store. Make sure to clean the leak area, put in the dye, then wait for about a week or so, and use the dye light to trace where the leak is coming from. The only known leak in that area that I know was from the power steering reservoir. It leaked onto the frame and I thought it was from the clamp, but it was from the p/s reservoir, which cracked on the bottom.

[@kuroshitsui1292]

+NutzAboutBolts alright. thanks! your videos are great too very helpful, the only channel I've found that works on 7th gen accord. Thanks again

[@NutzAboutBolts]

Kuroshi Tsui thanks! let us know how it goes. :)

[@Youthoughtso185]

Is there anyway you can make a video showing how to replace the driver door window regulator and motor in the honda accord 2003-2007? That would be so useful. Thank you.

[@NutzAboutBolts]

+Derek we'll take that into consideration, as it is pretty much the same like this and then removing the motor.

[@Youthoughtso185]

+NutzAboutBolts thank you.

[@MindOverEverything]

Good video. Can you give me any advice on how to get to my ECU on a 7th gen Accord? I haven't found anything useful online. Thanks!

[@NutzAboutBolts]

+MindOverEverything It looks like it's behind the center console of the vehicle. You'll probably have to remove the center box to get access to the ECM/PCM.

[@MindOverEverything]

I was afraid of that :) Kind of hoping for a way to it via the glove box, but I'll just have to give it a go through the center. Thanks!

[@NutzAboutBolts]

MindOverEverything what is wrong with your ECM if I may ask?

[@MindOverEverything]

Nothing. Just want to make it tuneable :-)

[@NutzAboutBolts]

MindOverEverything oh ok. lol gl :)

[@jz8179]

Shit,I have to take my door panel off cause my drivers door won't open from inside and outside the car with the remote and using the key on the door to unlock it it won't open.Ive got my work cut out for me.

[@johncasoni4379]

Same problem, how did you get panel off with locked door?

[@paulshires7914]

The gooey stuff is called butyl sealant

[@NutzAboutBolts]

gracias :)

[@stepheng8513]

My daughter took my 07 Accord out the other day left the windows down and water all in it wondering if it will just dry out on its own

[@NutzAboutBolts]

I believe it will, the electrical component is well covered. There’s no open electrical wire to cause a short.

[@stepheng8513]

Ok thanks. Real quick my driver side goes down but non of the other will go down so far keep my fingers crossed.

[@NutzAboutBolts]

@@stepheng8513 is it only the master switch buttons doesn’t work? Have you tried those individual window control on the door? If they all work individually on their own door, then I’d suspect it’s the master control switch on the driver side door that is at fault. I’d get another switch and swap it out to make sure it works. If not, you’ll need to further diagnose the electrical issue or the switch.

[@stepheng8513]

The other windows won't go down even if I try it from that individual door

[@NutzAboutBolts]

@@stepheng8513 does that happen on all the windows?

[@lolabunny1157]

My key literally fell down into the door panel 🫠😂

[@NutzAboutBolts]

Must be a big gap. 😬

[@lolabunny1157]

@@NutzAboutBolts lol it was a tiny house key it fell under the rubber thing in the door :(

[@NutzAboutBolts]

@@lolabunny1157 oh, thought you meant the key fob lol

[@JolinHard]

Can I access window like this? My window is stuck at the bottom

[@NutzAboutBolts]

Yes, you can access the window if you open the plastic door panel. It’ll be on a window rail track that goes up and down by using the door control.

[@JolinHard]

@@NutzAboutBolts thank you for fast response! I wasnt able to pull it out with ruler/tape so i will remove door panel

[@NutzAboutBolts]

@@JolinHardthe window glass is held on by 2 10mm bolts I believe. Just be careful not to break the glass

[@JolinHard]

@@NutzAboutBolts man I got the door panel off but I can’t seem to pull the window up still

[@NutzAboutBolts]

@@JolinHard you can’t pull it up, you’ll need the window regulator to work

[@friendly_italian4928]

Why won’t my door lock now?

[@NutzAboutBolts]

🤷🏽‍♂️ what’s the history on it?

[@c5scottman]

At the 4:00 mark you skipped the part of how to remove the cable.

[@NutzAboutBolts]

c5scottman it was more of an overview of how to remove it and see what’s behind it, kinda like what the cops do, strip and search 😉

[@garysilvers1721]

Rear door glass please ?

[@garysilvers1721]

The frontglassis easy

[@garysilvers1721]

Rear door glass please

[@NutzAboutBolts]

@@garysilvers1721 should be the same.

[@tommiestinson2146]

I hate when they talk so much in the beginning of the video just get to it!!!!!!