2004-2008 Ford F150 Leaf Spring Repair Kit and Installation Instructions | 43-1679-2

You can buy these kits online at: simcoespring.com/products/43-...
Whenever we make up a kit like this, I always want to make it as simple as possible for the end user. So, we include all the necessary parts to install this kit. No more searching for other parts to fix your vehicle.
Just remember this repair leaf is 47.5" long and is used to fix the 3 leaf Ford F150 rear spring.
This kit includes:
1 Repair Leaf
2 Clip bolts, sleeves and nuts
2 Center Bolts with Nuts
2 Ubolts with Nuts and Washers
Check out our store: simcoespring.com/
Follow me on Instagram: / simcoe_spring
Follow me on TicTok: www.tiktok.com/@simcoespring?...

[@wileecoyody3015]

This kit worked perfectly. I highly recommend it.

[@bobhudson6659]

From a retired mechanic in Land Down Under, suggest you place a thin sheet of steel across the back of each wheel when used the oxy cutting torch to remove the top nuts. There are brake hoses and other items that may not care for a "roasting" with molten steel splashes. You may have had something in place but I did not see it. Otherwise well done. The only extra thing I have done with U bolts is after tightening give them a substantial "love tap" or two with a lump hammer to help the U bolts seat into place. Then give them another check with a torque wrench. I generally find the U bolts take another 1/2 or so rotations before they get back to torque spec. However, you will have no doubt fitted many more U bolts then I have and you may have another trick or two up your sleeve. You have a thumbs up.

[@andyg817]

Totally agreen even some thick rubber matting to stop those sparks melted bits....

[@kinneticlandscaping117]

Bought my repair kit today from your shop , thanks for the great instructional video !

[@iamrichrocker]

congratulations on 100K..and already up 25K..that hard work and great content with your affable presentation is paying off..well deserved..

[@simcoespring]

well, Thank you very much 😀

[@dilipthakor8004]

AWESOME VIDEOS SCOTT! VERY INFORMATIVE FOR A LEAF SPRING ACCOUNTS MANAGER LIKE ME. THANK YOU FOR SHARING.👍

[@BlackPill-pu4vi]

Now that you're making this spring fix-it kit available, I'd expect a lot of vintage CARS with sagging rear leaf springs to ask for something similar. I remember a friend who had a Ford Maverick, many decades ago, and how badly the rear sagged. He put on extra long shackles to correct the problem but, it looked pretty bad going down the road.

[@Graveltrucking]

I’ve never really had any luck just changing out just one leaf in a pack the main leaf breaks shortly after. To change out the springs in that truck you’d be into new shackles and hardware. New springs are cheaper to buy nowadays with them being mass produced. When I was in my teens with 1 ton Ford dually trucks back in 95/96 we’d have to get a spring shop to make spring packs, it was expensive back then. Dendoff springs in Vancouver BC was the most common company to use. A lot of guys would get their springs re-arched that was pretty much a bandaid it wouldn’t last long.

[@jackdawg4579]

Been a lot of years since I have a vehicle with leaf springs. Spring technology must have changed a lot since I had one, my 1 tonne ute back in the day had a pack of 5 leaves in it.

[@georgeescaped6035]

looked pretty simple, all i need is a hole in the ground to roll over- a torch to cut off those parts- die grinder- i have the air wrench and sockets- and the kit... no problem!!

[@danieltorrens4954]

Do you think that we should do both sides while we are working on it?

[@simcoespring]

great question. If you can afford to, yes. shipping is cheaper when done in pairs, installation is easier when done in pairs. and usually the other side will break in less than a year because they have both seen the same mileage. However, not everyone can afford to do both sides at the same time, and not everyone will be keeping the vehicle for very long, so it is all up to the customer and their situation.

[@nathanblagdon3412]

What is the likelihood of removing those nuts and bolts without a torch? I have a reciprocating saw and die grinder.

[@simcoespring]

When passing a mechanic license it states to never use a grinder or reciprocating saw due to the Ubolts being under load/pressure. it could result in a zip disk breaking and coming apart.

[@garrynicholl8777]

Do u have repair kit for 2006 ford ranger. How much

[@simcoespring]

we currently have repair kits for: 99-18 silverado/sierra 04-08 F150 19-14 F150 Toyota Tundra Toyota Tacoma Nissan Frontier any other "kits" would have to be made in our shop, custom to the truck.

[@garrynicholl8777]

How much to make a kit for both sides 2006 Ford ranger

[@aytonbob]

You make it look easy ?

[@simcoespring]

I hope so. I've installed a few hundred of this part number. I think we did it all the hard way already enough times to know what not to do, which leaves the easy way left over.