2004 Acura TSX || Winjet Automotive Aftermarket Foglights

[@adrianc61]

The video was helpful and just finished my fogs! Thank you!

[@jaerex1]

Used your instructions, very helpful. I did not use the fuse adapter because the one I purchased was too large. I ended up just wrapping the ignition wire to the 7.5 amp fuse. I also did not remove the bumper.

[@chiingythao570]

Does your radio stay on if you turn the fog lights off and turn key off? Cause mine does unless I press the fog lights to be on again then itll shut up

[@XxAtomic646xX]

If you have big hands and/or also pushed the grommet through getting it stuck, you can cut a small slit and use the grommet that has the big harness coming through, its right near the fuse panel also. Much easier.

[@DIYD]

4 years later. so that red wire that's going into your fuse box in the car ... what is it connected to; is it part of the package or something you spliced on the car?

[@nealfraser4052]

Hello, thanks for the video it was very helpful. My foglights work a for awhile then stop working. I then have to unplug the from the fuse box in the car then they might start working again. I have checked the wiring and changed all of the fuses. Any other suggestions?

[@estebantovar6679]

Does the fog light switch naturally glow when car is off? Mine does and wanna know if it’s normal.

[@jefferyguthrie4230]

so the harness winjet gives you has a switch plug that goes into your fog light switch. it has the yellow female plug attached to it as well as the red positive wire and the black ground. i see the black ground goes to the 10mm ground bolt but you are taking the red wire and connecting it directly to that add on adapter you bought from o'reilys part store so you don't have to connect to the black and red accessory wire harness you mentioned about doing a t tap on?

[@HiDDENk00l]

If you want amber fogs, make sure to either buy the amber kit, or if you wanna DIY it and wrap with headlight tint, then get some amber bulbs. I got some tint that I thought was come out too yellow (almost green) when I bought it, but after installing, I realized the light was actually too white, because of the bulbs

[@gmen4life963]

Wait so instead of using a wire splice connector for the red wire & ACC you use the add on fuse connector instead ?

[@KseriesWill]

This video is old but hopefully you reply do you need 2 fuses connected to power it on?

[@michaelmilosiewicz6776]

Is there a slight green/ yellow glow around your fog light switch? I just had mine installed and that's what it seems.

[@PREDATOR-to8sp]

Michael Milosiewicz my button is green and is your button light Supposed to on whenever the car is on or off? Because my fog lights and my car is off the button is still glowing green...

[@xHoangLy]

PREDATOR2167 my are off when my car is off.

[@xHoangLy]

Michael Milosiewicz mine glows orange.

[@angelc8742]

it looks like you tried your best on this video and I like that, thank you very much it helped alot!!

[@xHoangLy]

I'm glad it helped!

[@mxmang]

didn't want to use a relay and battery votage with the factory switch?

[@vi_EviL_iv]

Where did you managed to get the OEM fog switch, part number?

[@markyazurin6304]

Does your sun roof button, VSA button, and heated seats buttons light up/illuminate in the dark when your driving lights are on?

[@xHoangLy]

Marky Azurin they do.

[@markyazurin6304]

Does the buttons on the steering wheel light up also?

[@xHoangLy]

Marky Azurin no.

[@muzaffersezen9048]

is there a died bug at 00:55 ?

[@nvask8rs]

Do your fogs switch off when your high beams are on? I want to get fogs but in my state, they must switch off when high beams are on in order to pass inspection.

[@xHoangLy]

nvask8rs the fogs were independently wired. They have a switch to turn them on or off. I can have them on with it without the headlights being on. With or without the highbeams on.

[@nvask8rs]

In your state, do they not care about that for safety inspection? VA's too strict ): But anyway, awesome video! will update you if I do throw on some fogs on my TSX

[@chiingythao570]

I wired my 2005 this way but if I turn the fog lights off and take the key out the radio stays on until I turn the switch back to on. Anyone else have this problem. And all my wires are different colors

[@trillzz-4645]

You think this’ll work with my OEM wiring? My fog light cracked and im not tryin to pay $139 a PIECE for them.

[@grimmcharest8102]

Yes they are the same plugs so you can buy a set of these and just use the oem wiring

[@jasonmedeiros287]

wat website did u get that print out of the wiring?

[@xHoangLy]

Jason Medeiros not sure what print out you are referring to. If you are talking about the fuse thing. Its in the back of the fuse cover in the car.

[@jasonmedeiros287]

About half way threw, your under the dash, briefly looking at a wiring diagrahm

[@xHoangLy]

Jason Medeiros o I see. I did a google search and digged through some online posts and got my self a pdf copy of the car service manual. I don't remember the exact website sorry.

[@taxiservice8404]

do you know how to do it for a nissan murano 2005

[@xHoangLy]

Gerson Menjivar I am not familiar with that car. I'm sorry.

[@jonathantrejo8627]

what is the brand of those fog lights?

[@milljo68]

listen fucking dipshit

[@squirlmy]

@@milljo68 worse than that, "Winjet Automotive" is in the video name.

[@TheRoyalking761]

Thank you, this is very helpful!

[@terrellbrathwaite5689]

Whats the fuse connector called

[@xHoangLy]

mini add-on circuit holder

[@xHoangLy]

9:44

[@JoseL9]

Helpful 💪 thanks just did mine today

[@LowNKum]

what disappointed me was that when I got my aftermarket fogs on... the adjustability of them wasn't what I expected.

[@dcc3657]

How are they now?

[@xHoangLy]

they are great. no cracks. the yellow tint hasn't faded. seals are good because moisture hasn't gotten in. switch still works. no problems so far. still bright as well.

[@vision27]

Wow thanks so much for making this video! I had the hardest time trying to figure out how to feed the wire through firewall.

[@xHoangLy]

Happy you found the video useful!

[@joethegreatest4491]

Helpful tutorial thanks man

[@normellow]

You Rock Hoang !

[@geomartabalno7816]

thanks man ,helped me wire mines

[@BeforeTheStorm]

Niceee

[@juanortega1278]

Thanks

[@sayonsok2230]

Doing this on my 2000 TL boyyy