2005-2007 Dodge Magnum No Start Loose Key Auctuator Pin Replacement

[@whatafetcher]

OMG ... thank you for posting this video. My charger had been having issues with the ignition for a couple months, dinging that key was in ignition when exiting the car being the most common. Usually was able to turn the cylinder and it would reset. Then Tuesday, engine wouldn’t turn over when trying to start. I did a Google search, found this video, ordered the part, and waited. I second guessed my gut and had the vehicle towed to a chain automotive repair shop, who in turn told me I needed to take it to dealer because the issue was in the ignition someplace. Dealer said they couldn’t even look at the vehicle for a week and a half, so figured couldn’t hurt to give this a try. Thank you so much! After putting everything back together, the car started right up first try. I couldn’t have done this without you and it saved me probably $600 in total.

[@SteveDavisCarGuy]

whatafetcher 🙏🏿 glad I could help you out. That’s what my channel is all about.

[@jeremyclemons6864]

What did you use my paperclip won't work

[@whatafetcher]

Jeremy Clemons - I used a metal clip I found in bottom of my tool bag, similar to a paper clip. I was able to short and get engine to turn over, but since ignition actuator was busted, cylinder wouldn’t rotate to start/on and wouldn’t start.

[@SteveDavisCarGuy]

Jeremy Clemons does your key not turn all the way?

[@flintjardeen8225]

Call Locksmith’s

[@bentleyaudio]

I just wanted to say: THANK YOU! I had thought my Magnum's no-start issue was a computer lock-out. But because your video was unusually thorough, and you made a point of showing the location of each and every screw and wiring harness to gain access to the ignition and actuator pin - I figured it was worth a shot. Hell my car has been sitting in the driveway for over a year (I had given up on it). So I followed your steps, and.... > BAM! < Problem solved! Total time: about 1/2 hour. Total cost: Under $50 THANK YOU!!!!!!!

[@SteveDavisCarGuy]

Amen❗️Glad you got it

[@15trai]

I had this video playing as I replaced my actuator pin, very informative and solved my problem. Thanks for saving my pockets.

[@SteveDavisCarGuy]

Trai Mobley 💯

[@marvinparker7872]

Bro how much the pin cost

[@15trai]

@@marvinparker7872 around $40 if I'm remembering correctly.

[@gregbrockjr3247]

Last night I had this problem. Went to pick up my nephew from work at 11pm, got out the came nothing no start . i remembered I watched the dodge no start on your channel. You help us to get home safe with your content 🙏 keep doing what you do. #LifeSaver Supporter For Life!

[@SteveDavisCarGuy]

greg brock jr that’s wassup thanks for the support 💯

[@douglasgraef7831]

This is one of the best videos I've seen in a long time you achieved exactly what you said you would with a little bit extra . starting the vehicle without the starter relay that was awesome when I did that I got the confidence that I was in the right direction and you knew what you were talking about thank you very very much you should make more videos this one is awesome thank you so much

[@SteveDavisCarGuy]

douglas graef 🙏🏾🙏🏾🙏🏾 thanks for the support ✊🏾

[@lonneebelton9806]

How'd you turn the car off afterwards?

[@jibeyasthappan9582]

Thank you! Jumping 30 and 87 didn't work for me, but replacing the actuator pin did the trick. Thanks again!

[@DCUnderboss]

Jumping same way didnt work for me either . took all this apart but cant tell if its bad

[@jameshill9161]

@@DCUnderbosswhat happened.. goin thru it now

[@DCUnderboss]

Faulty starter and power wire to starter was in bad shape.

[@outoftheblew314]

Video is on point. Never knew this part existed. Neighbor lady has an '07 Charger, she was asking for a boost, which she hasn't needed since having me install a new battery​. Found the ingition wouldn't turn off, and the car wouldn't start. This was the 3rd video I watched, and by far the best. Her car would not start using the jumper wire. (would crank but no start). swapped out the ignition actuator switch, started right up. About an hour, that includes going to get the part. Great Video! Thanks!!

[@SteveDavisCarGuy]

outoftheblew314 Hell yeah man that’s wassup ! 😁😁

[@shanamiller7331]

This video is bomb.....cant believe it took me 2 years to find it.....my magnum has not been started in 2 years it keep me from a ton of trouble....I rolled over and wanted to start but wouldnt turns out the fuel pump fuse was blown also so it was cranking and not starting.....but now it runs thank you so much for your help

[@davidhuffman8543]

Bro, thank u for uploading this video. I been having issues with my ignition switch and it's left me stranded a few times the past couple days. Sometimes my key works and cranks the starter but sometimes it doesn't. I don't have money to replace the ignition switch for couple weeks and this video showing me how to jump the starter just saved my ass.

[@SteveDavisCarGuy]

Nice that’s what’s up

[@tpformybunghole1974]

Thanks for posting video. My wife's charger wouldn't crank and was stuck with the PRNDL and odometer illuminated, basically the car was stuck in ACC function so radio and windows worked with key out. The cylinder turned but function wise it was stuck in ACC. Bought the ignition switch (black part on the end the large connector plugs into) and the actuator pin and good thing I did because actuator was broken and piece was stuck in switch so couldn't reuse ( there's extremely small torx screws on the back of the switch so maybe disassembly was possible to get broken piece out but I had a new switch so i used the new one and new actuator pin) fixed the car in less than an hour and avoided a tow headache by fixing it right where it broke down.

[@SteveDavisCarGuy]

Nice

[@richardchubey4826]

Thank you for your video it helped a lot. A few points were missed though. Reinstalling the new part. I had a lot of issues because the broken metal from the old unit was still lodged in the housing. My fault for not recognizing this. Spent 10 minutes before I realized this. Also on reinstall there is a cable with a yellow tang the needs to be installed. Drove me nuts for 10 minutes. Key must be in the ignition on reinstall of this cable and turned slightly otherwise reinstall is impossible. Never the less I thank you for this video. Saved me about $800 today. If you are ever in Calgary I owe you a steak dinner and a few adult beverages. Hit me up if you are ever in town. You saved me $800 I wont forget that! Thanks again!

[@SteveDavisCarGuy]

Richard Chubey just reverse the steps 🤯

[@AlfredoHernandez-xr4dx]

Just wanna let you know that between your vid and another persons,you easily saved me $600....I got stumped on that one plug that was hooked the ignition but watching your video I got it no problem...Thx again!!

[@sacproducer]

Thank you kept me from being stranded and saved me money on tow fees

[@SteveDavisCarGuy]

Clutch ‼️🤘🏾 Glad it worked for you, a lot of ppl say it doesn’t.

[@EdwinTorres-l9d]

Nailed it. Good job, and it only cost 20 bucks. Thanks

[@DocHicksTv]

What were you using to to jump it under the hood? Two separate safety pins? Or one long metal piece? Couldn't see what you were using bro

[@SteveDavisCarGuy]

Anything metal. You’re just closing the circuit

[@matthewmoorecichlids2323]

Couldn’t thank you enough for that starter trick

[@SteveDavisCarGuy]

Glad it worked for you

[@nelsonricardomontalban1780]

You are a prince and savior this video is very detailed professional and very helpful.. Thanks alot...

[@SteveDavisCarGuy]

😂😂🙏🏾

[@roscko5624]

Thank you thank you thank you!!! Hahaha I had to keep watching the video because the second time I did it I did it wrong and shocked myself but your video is well detailed!!!! My car works for now till I can replace the ignition switch hahaha

[@SteveDavisCarGuy]

Nissa Rodriguez Glad I could help you out!

[@jeremyclemons6864]

What did you use my paperclip didn't work

[@tabithakavanaugh1307]

Good work on this video! I have a 07 Magnum SXT. After trying like 10 things to get my car out of anti theft mode, replacing the acuator pin is what worked for me. The paper clip trick made my car crank but not turn over, but i only had it on "on" position. Im guessing you have to have someone or something holding it in start position?? The crank did tell me it wasn't my battery or alternator. THANKS for posting this! 😊

[@valeriejackson4261]

Maybe u can help me my wagon my car caught a fire in the inside on the drives side in the garage. Two people have said it was the Cadillac converter on the muffler or electrical it appears to have started from the flood and everything on the drivers side is burned even my drivers door. It's still starts and the windows are going down ,radio working as well. Can u please give me your thoughts. My car also just killed on me before this fire and it started back up. Eye parked it for 2 days and then dicied to park it in the garage mind u the garage has no ventilation in it as well so do u think that may have trigger the fire?

[@toddwallin1891]

This video helped me find my problem fast appreciate it man thanks.

[@NFL_VET89]

My guy always got a good video somewhere 💪🏾

[@chemiv-sh7xy]

Im going thru this right now . I opened the box and the actuator flew everywhere now idk where the big spring goes. Can't find videos on the assemble of the actuator

[@KerryOnDaBeatz901_]

I’m watching this video as I’m stuck at the gas station rn with this problem can’t wait till I fix it

[@danielaguero3766]

Just wanted to say Thank You I just recently had to replace my actuator pin , damn dealer wanted to charge me $500

[@roscoec.2575]

Excellent video very detailed thanks!

[@ryanbowles9777]

Thanks buddy that video helped me a lot with my charger I really appreciate it

[@kyledevore871]

Helped out!! Thx for the video!

[@joselinmiller3324]

Hello I got a Magnum in need of mechanic and electric work do you fix?

[@robynfrancis2393]

Hey so when it won’t start does your ignition, lights, gauges and dash board work... and it just won’t start? I have a 04 Durango magnum 5.7l that will only start when it wants to

[@miguelgzavala2875]

U get down , I applaud this video. Thank you sir

[@miguelgzavala2875]

So I installed a new starter on my nephew's charger n it didn't work but I can hear the starter click. U think it could be the same issue.

[@miguelgzavala2875]

Have u ever installed a defective charger ,did urs click the same way it would if it was the starter ,I tried poking the holes on the relay were u said, but I might b doing something wrong

[@kimmerdarrisaw6775]

Thanks...sure helped me out!!!

[@godson197410]

keep up the good work bro 💪

[@SteveDavisCarGuy]

robb black Thanks Robb

[@godinez71]

Nice video very informative and detail.where the pin actuator seats have metal fragments in plastic can you use pick to scrape around before installing new one?

[@SteveDavisCarGuy]

Yes sorry for the lateness

[@stevenfontaine5751]

I tried to start my car the way you did but still wont start the car its cranking but wont turn over for me, what other issues would i have ?

[@lonneebelton9806]

That trick in the beginning on starting the car, how do you turn the car off afterwards??

[@SteveDavisCarGuy]

With the key

[@lonneebelton9806]

The Ignition pin broke so I can't turn the car on or off, It's stuck on exhilarating power, So if I start the car how can you turn it off without using the key?

[@remingtonlutz5098]

THANK YOU for this vid bro. Quick question tho when I put it all back together the car thinks the key is still in … everything works now I can start it but can’t lock from the fob anymore and the bell dings when the door is open :( any suggestions bro

[@SteveDavisCarGuy]

Unsure on that one

[@brandycalicott7077]

Now it is starting??? Could it be fuse or fuse box? Making me crazy

[@brandycalicott7077]

Totally stumped bypassing the starter relay worked to get car started. Was convinced this was my problem, took dash apart checked and my actuator pin isn't broken. Got any other ideas? I've replaced the battery and starter trying to fix it I was hoping this would solve my issue.

[@silviasolis4587]

When replacing the actuator pin, do u have to replace your key?

[@SteveDavisCarGuy]

No you don’t have to

[@MrsBuddevil]

@@SteveDavisCarGuy Do you have to remove the key? Reason I ask is the key is broke off inside. Friend has '07 Charger 3.5. She thought it was stuck in limp mode(it would accelerate over 2800rpm) so she had me use obd reader to check and erase codes. After that it cranked and started a few times but would die after a few seconds. Now there is no crank no start. ?? I'm at a loss.

[@keithbarnett4428]

Hey I have a 06 charger rt. Got power and was told battery is good as well bit wont start. I tried the safety pin and it started but didn't crank. My key does have some movement. How much movement is there to indicate replacing this??

[@SteveDavisCarGuy]

It’s hard to explain how much movement, sorry for the late response

[@treborsnikwad]

Hey, Steve...I had the same starting issues, and I tried the pin jumping trick you suggested, but now I don't have any power to the car at all...the paper clip got really hot, but the care didn't start and now the battery seems like it's dead. Any ides?

[@SteveDavisCarGuy]

Robert Dawkins Do you have a volt meter? Sounds like you blew a fuse in the main box (trunk near spare tire).

[@treborsnikwad]

I checked the fuses, and they were all okay...turns out that the battery had a bad cell in it (even though it was only a month old), so Wal-Mart replaced it for me, and it seems to be working. Your video is excellent for fixing the ignition actuator, though...I'm sure I'll have to do it one day, so I've bookmarked your video. :)

[@richardchubey4826]

@@treborsnikwad Definitely bookmark this you will need it! I am on my 3rd actuator pin now. Also sorry your new battery crapped out. Nothing worse than diagnosing issues when your new parts are faulty!

[@gabrielmendez49]

Was it cranking

[@vernonbolinger9488]

Do you have to have the key in the Run position or the start position for it to start when I have mine in the Run position it just cranks and won't start when I bypass the starter relay

[@SteveDavisCarGuy]

Vernon Bolinger run, if it cranks and don’t start you have a different issue

[@vernonbolinger9488]

@@SteveDavisCarGuy turned to start position and it started quickly when I bypassed starter relay. When I got car home I tried it again both ways and it will start either way. It just has to crank longer when it's in the run position as opposed to the start position. Actual problem is fixed. It was a broken actuator pin.

[@SteveDavisCarGuy]

Vernon Bolinger I did this like twice, I don’t know how many times you can do it.

[@MARTHAWAGGONER]

This was so helpful. Ty!!

[@derbaderba5258]

Just stumbled on this gem, I’m not sure if it’s going to fix my issue or not but here’s to hoping! I stopped to go inside a gas station came back out, put my key in and it turns but there no resistance, there’s no click for where the accessory power is and you can’t even try to turn it on because it does nothing. The key just turns freely on the cylinder, I’m guessing this would be my issue

[@SteveDavisCarGuy]

@@derbaderba5258 let me know if it works

[@derbaderba5258]

@ it worked!! I took the actuator pin out and the tip of it was broken off into the black piece that it connects with. Replaced it and she started like a charm

[@brentblackberry9205]

Hey Steve , I have a few questions about this . 1 , will this hurt the computer or any other system ? And 2 , my 07 magnum will crank but it won't start . Why and do I need somebody else to help with the key or accelerator pedal ? Thanks .

[@SteveDavisCarGuy]

Doesn’t effect any of your systems, if you need a second person this is not your issue.

[@brentblackberry9205]

@@SteveDavisCarGuy thanks bub. Just making sure . I changed the actuator pin anyway . It was broke . Leave it to an auto maker to make crucial part out of pewter and plastic lol.

[@kendrickcontent]

Mines wont start using the fuse trick? Why

[@DeeDogg]

Would this work for a 07 RT?

[@SteveDavisCarGuy]

Yup if that’s the issue

[@tonytamayo4547]

Thanks for the video!!

[@kendrickcontent]

My actuator pin is intact not broken but I gets nothing when turning the key to start like completely silent. The fuse trick didnt work why so?

[@SteveDavisCarGuy]

That’s not your issue then. You have something else going on

[@kendrickcontent]

@@SteveDavisCarGuy im thinking its the ignition switch or immobilizer on the ignition or chip in my key idk which tho.

[@uhmeizuhngralphf0549]

Good video thanks for posting

[@dennismason9448]

I got the security light like you but the safety pin bypass doesnt get me a crank, whats that telling me?

[@alejandrolizarraga3898]

Did you got fix bro my car doing same thing please help

[@dennismason9448]

@@alejandrolizarraga3898 if jumping relay dont get you a crank, you dont have enough voltage from battery. New battery or alternator is the fix

[@Hunnidbandhustla]

Bruh what type of pins are you using to crank because im stranded

[@naterusscomedy]

This helped me out!

[@SteveDavisCarGuy]

Ayeee 💪🏾😎

[@mikebarrett3982]

What did you use to start car in the beginning of the video?

[@SteveDavisCarGuy]

Mike Barrett piece of wire

[@mikebarrett3982]

Anykind will work? I'm currently stranded at a McDonald's and I'm next to an auto parts store.

[@SteveDavisCarGuy]

Mike Barrett Yes any will work

[@mikebarrett3982]

@@SteveDavisCarGuy thank you so much for replying I had no idea how I was going to get home

[@SteveDavisCarGuy]

Mike Barrett did it work?

[@T.Sumpter]

It won’t give me my key back when I try to put the wire back on... do you know why?

[@SteveDavisCarGuy]

Still doing it?

[@T.Sumpter]

I got it towed to the shop and let them do it.

[@SteveDavisCarGuy]

Torrance Sumpter damn 🤦🏾‍♂️

[@sickboycd1]

Too late now but in case anyone reads this post and needs to know why the key was stuck....when first disassembled as your approaching the part where you dis-engage the security node (the black plastic box on the side of the cylinder) you put your original key in the cylinder and turn one quarter turn clockwise to the accessories position and while keeping the key in that orientation, slide the clip up and push on the tab on the harness itself as you pull on the harness all in one fluint motion, the clip, harness and node (provided you've removed the 3 torx and 1 phillips screw from the side of the cylinder housing prior.{Without describing everything the author all ready did such a beautiful and speedy job of doing first!} ) Once you slide off that harness you could technically pull your key after returning the key to the off/stand by position but typically I just leave the key as I'm installing a new cylinder with all new parts, security node/module, harness and 2 programed key fobs programed to the new node and keys cut to the new pin locations in the new cylinder. If your reinstalling the same cylinder and node just changing out the broken pin in the back the just leave the key in, install the harness once to that point and turn your key back to off/stand by. At the time of completion you'll be able to turn it off and pull it out with ease since the security node harness has been reinstalled. That should answer your question. Please forgive me if I left out a nail/staple or forgot to air up the blinkers I'm sitting on a white chair that's very cold, the white wall is 15 inches from my face and all I can see is my shoes, socks and shorts maybe the rug under my feet. In other words as you are using your imagination to guess where I am and what I'm doing right now I'm using my imagination to think about how I steal chargers in my spare not so free time! Totally joking...about being in the bathroom! Gotcha!

[@sickboycd1]

Oh the free time too. I don't do that. Waist my valuable time I mean. Ok enough jokes. My man made an absolutely great and very much needed video on these plastic cars. I really needed to watch it and couldn't find another like it. Thank you. I really appreciate you taking the time to make it.

[@LowKramer]

Need no would that problem make your starter not turn over

[@jeremyclemons6864]

Thank you bruh

[@woodgranecustoms]

you pretty Dame smart mister

[@SteveDavisCarGuy]

Woodgrane Williams Thanks bro I have hunger for learning every single thing about a car 😄

[@monsterthekid1081]

I have a 06 Magnum 3.5 v6 rwd yesterday while waiting for work to open, I have my car off, but the radio on; everytime she went off I would turn the key to the auxiliary power and listen to the radio, I did this about 5 times in a course of 30 minutes. The car cranked over 2-3 times for like 5 seconds then died and now it won't start at all. I get power to everything, battery is good fuses are good, but I did notice the red anti theft light on now which was never on. My key for is shot and, I only have the one; do you think it could be the alarm that's shutting down the car? I believe it is because it thought I was trying to still it by doing that dumb shit yesterday, my car run quiet no smoke, pings, knocks anything, I don't beat on her, I don't even know she on sometimes because she so quiet and she doesn't shake. Any help is good help bro👌👍✊💪

[@SteveDavisCarGuy]

Monster The Kid Sounds like you need a new battery or your current battery charged

[@aaronbottley6812]

im having the same damn issue now how did you fix it? was it the security?

[@stephenjohnson2906]

AARON BOTTLEY same issue u fix it

[@GuTvUncut]

Did your car have the red volt on the dash when this happened to you?

[@SteveDavisCarGuy]

I don't believe so

[@GuTvUncut]

Steve Davis ok thank you think i’m having a connection problem tried tapping in to the fuse also and nothing but all light and music still working and and battery is at 12-14v

[@raquelb731]

This is very good information you are very knowledgeable however redo it showing the full panel and I absolutely think you would be a KZbinr pro

[@Oatmeal_TVx]

You are awesome

[@Ryot_00]

Hey thanks so much man you saved my ass. I managed to switch it out thanks to you but the thing is now my car won't stop with the beeping noise after I open my door and the key is not even in the ignition. It only used to do it when I turn off my car open the door and leave the keys in the ignition. You think I might of installed it in wrong?

[@jonrogers8172]

I changed the pin an now it’s not making any noise

[@tank100286]

Im actually at my job right now and my Dodge Magnum 2005 RT Hemi isn't starting. Roadside services said my battery is new, and i told him, i just got a brand new starter last year. Before i went to start my car though, for some reason, I notice the part for my keys was off and kinda cracked. I heard that magnum car keys has a sysyem were if the key is loose or broke. The car wont start. My question is, is that true?

[@SteveDavisCarGuy]

+Mike Tank Brown ll I couldn't answer that one bro sorry

[@TheHoneyhill]

I replaced the pin and the ecm my car still want start

[@SteveDavisCarGuy]

If the key didn’t fell loose, there was no need to replace the pin

[@TheHoneyhill]

The pin was broken

[@mattclay8121]

Starter will crAnk but no start from the paper clip

[@SteveDavisCarGuy]

+Matt Clay sounds you may have a bigger issue

[@a....1694]

I try to start it where the fuse is and it won't start I did it exactly like you told me to do

[@SteveDavisCarGuy]

Antoinette sch Is your key loose?

[@uno25]

You're good but hand that cam to a kid. They would do 1000x better holding the cam. Doing multiple things at once isn't your thing.

[@SteveDavisCarGuy]

UNO25 That's definitely my thing I'm glad I was able to help you thanks.

[@flintjardeen8225]

FOH

[@MrJohnnyo45]

Thanks for nothing. Your camera shot doesn't show where to put whatever you put in place of that fuse to start the car

[@gabrielmendez49]

Mine just stall random n then when trying to crank it back up it like crank for one second and stop cranking like someone killed the signal to the starter the. I let it cool down for a hour it start up and i dont replace key crank sensor with mopar parts

[@gabrielmendez49]

But did a it crank and like cut off like if u stop trying to crank it

[@SteveDavisCarGuy]

You have a bigger problem it sounds like

[@gabrielmendez49]

No but im asking wat was your symptoms

[@gabrielmendez49]

Like did it do wat i said or there was just no crank or anything

[@DocHicksTv]

​@@SteveDavisCarGuyHey, was that 2 separate safety pins you uses under the hood? I couldn't see what you stuck in that fuse spot to jump the car. If you don't mind, please let me know. Currently going through that issue. Thanks in advance Stay blessed

[@gabrielmendez49]

Would crank for like a sec n then not start

[@fabianparson3378]

Great video! Thank you