2006-2009 Ford Fusion/Mercury Milan Door Handle Replacement

[@maureenmichaels6475]

The driver's doorhandle broke on my son's 2009 Mercury Milan the day before Prom! I'm a panic, I searched for a way to fix ourselves and came across this step-by-step video. THANK YOU so much for posting this! I am not mechanically inclined, but followed each step and fixed it ourselves!! Crisis averted! Thanks again!

[@SosAhallow]

Best video ever I changed all 3 of my door handles less then 10 minutes no cap

[@SosAhallow]

And it’s 95 degrees outside

[@scottyo911]

Great video. Did this myself in a few minutes. Note, I didn't remove the electrical connections. The cable was long enough that I could rest the panel on the ground while working on the handle.

[@laurieadamson5355]

Thank you for this video! My husband and I successfully replaced the driver's side front door handle on a mercury milan. There were more cords and 2 screws on the door panel not one but all the details of your video provided enough information. It was one of the easiest repairs we have ever done.

[@dannydoitall3312]

Thank you

[@MichaelOnRockyTop]

Dude thank you so much! Got it done without breaking any plastic tabs at all and saved a lot of money!

[@dannydoitall3312]

Awesome

[@robertfitzgerald9632]

Excellent instruction. Great attention to detail.

[@johnbrady3021]

Excellent video, went on quickly no problems except getting the initial tab part out. I used a stanley box cutter blade to wedge it out. Thank you for your step by step very helpful!

[@WarrenBell-w6l]

Good video. One of the best I've seen. Very detailed

[@m1t2a1]

When the drivers door of my '08 broke, I learned that if you pull the door handle and lock at the same time the door opens. That was 5 years ago. Doubt I'll ever replace it.

[@KRonSimis]

You'd think that, until the lock itself breaks too :D

[@m1t2a1]

@@KRonSimis 245,000 on it, in the rust belt. There are three other doors.

[@j.l9385]

@@m1t2a1 😹😹

[@chrismalone4679]

Worked like a charm thanks

[@dannydoitall3312]

Great. I just broke the drivers door handle on my fusion the other day. Unfortunately these things are always breaking.

[@lkbpythons6210]

nice ride brother i would like to add mods to my 08 fusion but seem like good part are hard to find for a good price keep up the content on your fusion....

[@dannydoitall3312]

Thanks I will have some more videos coming. I agree most of the mods are expensive.

[@mamarobyn]

Yep...Have the same issue now. OPENING DOOR FROM THE OUTSIDE ALL THE TIME, NOT CUTE! TY TY!

[@dannydoitall3312]

Glad to help hopefully you got it fixed.

[@TheTiredhermit]

I feel that

[@danielspeesesr5719]

Thanks!

[@dannydoitall3312]

Your Welcome.

[@mathieuvvv]

I did this replacement but my key fob button isn’t activating the lock idk if it’s not strong enough now because it’s been broken for so long or if I just connected it wrong but the handle works fine and the lock it just doesn’t work with the key lock button any suggestions ???

[@Engwadur]

Would this be the same for a power lock door handle?

[@dannydoitall3312]

Yes, this video is done on a car with power locks.

[@John-b9s4b]

Quick question is that the same way you would put in a driver side door?

[@dannydoitall3312]

It is similar not exactly the same. The configuration is slightly different behind the door panel as it is bigger and there are more wires on the wire harness.

[@diegomartindelacanal9300]

Thanks 4 sharing PUMAS wins tonight

[@Lexx.Xclusive]

what if when you try to place the door handle latch cable into the new handle it’s extremely tight

[@dannydoitall3312]

You can try to put a little grease on it to see if will slide on. I bought an aftermarket door handle that I had that issue with. I put some grease on it and pushed hard and it slid on.