2006 Ford Fusion Front window motor and regulator replacement

[@JayCeeMax]

There is not a lot of 1st Gen Ford Fusion/ Lincoln mkZ content out there. I vlogged a fix for the 2008 model year. Thanks All Out Throttle for taking the time to put this together. Cheers.

[@Gsxforsale]

I like how you cuss out the clips. Sounds like me in the garage lmao

[@langer24106]

“I don’t really care if you can see it or not” 😂😂😂

[@AOT-offroad]

Don't forget to like and subscribe thanks again everyone!

[@eliquinones6088]

All Out Throttle ok so my window is stuck down same pos car, I have to fix it this week. A little confused about what to do with the rivets.

[@AOT-offroad]

You have to drill them out and then replace them with little sellf taper bolts or bolts and nuts. I mention it at 2:24 and 5:44

[@leogeezuz4161]

As much as there's many stupid comments I got to say it was most helpful and hilarious is fuck LOL sharing it with the friends.

[@paytoncampbell1683]

How did you get the rivets out

[@obm5223]

Ridiculously inept and totally unhelpful 😎

[@AOT-offroad]

The good thing is not everyone shares your opinion. Thanks for watching though

[@joehobbs3280]

I can kinda tell what you're doing, which makes your video kinda helpful but you lost most of the potential value because you don't hold the camera steady for more than 3 seconds at a time. It's like the blair witch project man. With a little more care your video would be WAY more helpful which would in turn make it WAY more popular...and isn't that the point of posting videos on youtube?

[@AOT-offroad]

Sure, thanks for the advice. I just don't allocate much time for these videos. I also edit with the purpose of keeping the instructions short and to the point. But yes a steady hand and less rushing would go a long way but that's not me :D

[@alawishes1733]

I was sitting here watching this video trying to figure out why this feels so familiar...then I scroll down and read your comment t"TA-DA" the Blair Witch Project HAHAHAHAHHA

[@AOT-offroad]

HAHAHAA valid points guys

[@jeff74801]

so did you put the new regulator on the inner section of the door first, then put that inner section back on the door, then secured the window to the new regulator?

[@AOT-offroad]

Correct install regulator on inner shell then install inner shell

[@jeff74801]

awesome! thanks!

[@maroman200]

Do you remember what size bolts you were using ? I wanna make sure I have them available when I do mine this weekend

[@AOT-offroad]

I believe they were .25" x 1" with some red locktite

[@maroman200]

thanks a lot !! Worked beautifully

[@AOT-offroad]

+Joseph Payer good to hear dude

[@jayandbrandie8372]

Hey bro where did u order the part from I can't seem to find it in my town or near by towns

[@AOT-offroad]

+jay and brandie Both parts from Autozone

[@brookejackson9145]

Really hoping my issue isn't the regulator

[@AOT-offroad]

Fingers crossed my dude

[@kd7cwg]

When I had my Fusion 1 got replaced under warranty, I had to replace the other 3. all less than 50k miles

[@AOT-offroad]

It really sucks doesn't it?

[@kd7cwg]

It does , I had a 01 focus, I replaced the driver's one. then the other 3 went within the same week. fortunately, I do not need to drive that thing anymore

[@zakoldog216]

Nvm the last seconds answer my question

[@zakoldog216]

So you don't need to fuck with the rivets I'm just trying to replace the window it shattered

[@RzVids]

Is it the same for the rear doors?

[@AOT-offroad]

I'm not sure, I do not think so though

[@mediamonitor980]

My fiance's drivers side window is stuck down right now. I'm thinking this will be a pain in my asshole.

[@AOT-offroad]

I hope the video gives you an idea of what to check first. The cross cables are a common issue.

[@dwalto02]

Thanks potty mouth

[@AOT-offroad]

+Dan Walton There's a harsh language warning.

[@MariaFatima-hr8bl]

quer ver com trazer o amor de volta