2007 Ford Mondeo TDCI(130) Zetec 2.0L Diesel Clutch Replacement

[@WMCS]

www.williamsmobileclutch.co.uk 🇬🇧 Contact us for your clutch replacements. Thanks for the suggestions and continued support for us small businesses. Kind regards. K-A. Williams.

[@stephansondkhar3964]

I need help for ecco sport automatic transmission to replace clucth plate

[@AT-AT3]

HI , how much time would you tell you spent to realise this operation ?

[@andrewmount278]

Massive thanks to Kevin for carrying out the clutch replacement on my Mondeo 👍 What a professional, I can't recommend him enough. Hopefully the rest of the car lasts as long as the new clutch. Many thanks.

[@jasonwiggins7894]

Yes he did a great job mate may I ask you how many miles your Mondeo has and also how long was the dmf rattling before you have the job done many thanks Jason

[@andrewmount278]

@@jasonwiggins7894 Hello mate, she's done 187250.miles. It started playing up early December, vibrations through the clutch pedal, it was ok when fully engaged and unengaged. But when it was partially engaged wow what a noise and vibration. I also had the clutch go all the way to the floor a few times, but it came back up if you put your foot under it. Hope that helps, I can't recommend Kevin enough though if you do get it changed.

[@jasonwiggins7894]

Wow that is great mileage no complaints there Andrew there's lots of Mondeo haters out there but I think they are a great car ready to do another 180000 then catch you later bud

[@andrewmount278]

@@leebenstead7171 Hi Lee No I didn't, the steering wheel was still centred well and she wasn't pulling either way. However I've just replaced the N/S lower arm ball joint and the steering wheel isn't central anymore and she's pulling to the left a little bit, so I will be getting the wheel alignment done now. Hope that helps.

[@andrewmount278]

@@leebenstead7171 No problem, hope it goes well. I normally carry out my own repairs and believe I could of done this one, but it would of taken considerably longer with lots of KZbin to make sure I was doing it right. Kevin worked like a machine and it took him 6 or 7 hours to do. It was well worth paying him to do the job for me. I just hope the rest of the car lasts for a good chunk of the clutches life. As the ball joint went just a few weeks after the clutch, I would highly recommend checking to see if any other components require changing whilst you are doing the clutch it could save you a lot of time. Good luck 🤞

[@ensamvarg1974]

You're a man among men. Thanks for sharing your work with the public.

[@frfrpr]

I have not seen anyone on KZbin film better than this. This guy has mastered the clutch change.

[@WMCS]

Thanks for the feedback 🍻

[@davidwilliams706]

Did this exact job on the same model car a couple of years ago on my drive. Took me two days and a bath full of Radox afterwards. He makes this look easy when it is anything but. Man handling gearboxes like that takes some doing, and he clearly earns every pound he makes. 👏👏

[@jasonwiggins7894]

Lol... me same as you David I had to get assistance getting the box out and in I didn't fancy dropping it on my lap

[@aurelienz1422]

Hi mr WILLIAMS. I just want to thank you from France. I could change a clutch on my 2005 Ford mondeo 2.2 TDCI thanks to you. The 2005 Ford mondeo 2.2 TDCI and the 2007 2.0TDCI ZETECH videos were very helpfull. I take my time, and now it's done. The way you shoot your videos are so precious and detailed. So thanks a lot, you do a great job under a car, but an another one as much great to filming your job, cut it, and upload it on youtube. Un grand merci pour vos vidéos et votre partage! Kind regards

[@ervinmq1955]

Kudos to you Kevin.... You just don't know how to quit... Even if it's raining, snowing or hell will break loose, you just keep going untill the job is done... Stay cool.... "Cheers" From Guatemala I salute you....

[@monipaczynska9957]

Kewin, świetna robota. Podziwiam Cię za to że robisz to na ulicy bez podnośnika w tak krótkim czasie. Szacunek.

[@3kocur]

awesome camera work among other things

[@cg7975]

You sir, have the heart of a lion. I take my hat off to you.

[@WMCS]

Thank you

[@m2mark1]

Thats a ball ache of a job on a ramp let alone on the floor, much respect.

[@andrey_hramyka_S]

Восхищаюсь твоей работай , что ты делаешь на улице это просто не реально у нас в России город Санкт -Петербург такого даже в сервисах не могут проделать ) уважение тебе

[@clayfree7428]

Might be cheaper to set fire 🔥 to it and claim the insurance money than to replace the clutch ! Great Job!

[@Floupel]

Thank you for making my life easyer

[@TheAmos1]

as always, very professional and making it look easy. fantastic job 👍🏻

[@TheAnimus14]

Amazing video, I work for an ford dealer as mechanic in germany and i can tell, 13:46 this screw is such a pain with newer models even here its hard to reach.

[@WMCS]

Very true. A lot of time it seizes up. Because the thread is exposed on the opposite side that sits in a recess dam that holds water every time it rains.

[@TheAnimus14]

@@WMCS But I have to say I take some ideas from your way to work. You are a great guy and awesome mechanic.

[@p0pp1973]

These videos are unreal. Your like spiderman under these cars. A pop up gazebo from aldi/lidl cheap and cheerful might keep u a bit dry on poxy days. Really enjoyed watching.

[@jeffmoss5822]

Kevin,another masterclass in mechanical engineering and documentary filming making. Great!!!!

[@matt23540]

This video makes the Mini videos look like a walk in the park! What a mission! You had to take half the car apart. You took it in your stride though and made it look easy….as usual :-)

[@andrepereira3176]

Ford Mondeo is very hard to work. Fantastic vídeo as always Thumbs up one more time👍

[@nikolaysafronoff1737]

Кевин, спасибо за твои ролики... Получилось самому, заменить сцепление с маховиком на vw T5... Удачи тебе!.. Привет из Архангельска!

[@wellwh0]

Those mk3s getting rare this days. My fav Mondeo.

[@WMCS]

Definitely.. they are like tanks to be honest ..

[@wellwh0]

@@WMCS yup. My dad has it. 16 years strong. Only issue is bloody DMF. Replaced twice.

[@maxthecaddy8451]

mammoth of a job with a huge gearbox, but still no probs for Kevin-Albert Williams. Thumbs up from me buddy 👍

[@WMCS]

Definitely was a tank this one 😁

[@joseraulmatosperez6533]

Con este video se aprende a desmontar y armar muchas otras cosas además del clutch ,muchas gracias por compartir tu trabajo, que Dios te bendiga y tengas exitos en tu profesion.

[@brianmason8400]

That car just kept giving didn't, as far as what all had to come apart.... great, clean job as always.....

[@stanislavstankovic2155]

Somebody need several days, what you are doiung in several hours. Very good video !

[@WMCS]

Thank you.

[@anisibrahim8931]

Nicely Kelvin..same as me done in Malaysia 🇲🇾

[@anisibrahim8931]

Can you share more video to me..I’m interesting your skill fix the car

[@osag.s.a6340]

I love watching your work mate thank you for all your efforts

[@WMCS]

Thanks for the feedback

[@robjames292]

As us mechanics we all know what there like. Il give you Kevin you do have luck on your side, the amount of chassis legs iv had to cut open to well the nut back on lol. Fer play!

[@arbeamngcrash3763]

Nice work as always remember doing one of these back in the day on my back regretted starting it 😂

[@Blechbüx01]

I wish we had such a Service in Germany too:-)

[@fix-and-drive-diy-repairs]

Nice job bro, Advice, start at the top fisrt while the car is on the ground. In that way, it is easier to reach because the car is not too high. Also, because you are alone, just put the wheels underneath the car just incase the jack stands falls or fails then the car will fall on top of the wheels. Cool😎

[@ricardo7360]

Great work on the Ford Mondeo TDCI

[@mrc7478]

Enjoyed this Kevin. Nice one. Also - easier when you lift the box off and push the subframe back up when reassembling.... (I'm using a jack) 😂

[@twik408]

This video perfectly shows how big a pain in the arse mondeos are to work on.....one of the most frustrating, swear inducing vehicles ever designed. Great work as always by K-A W

[@francescomolinari4342]

Grazieeee mille per il Video

[@shaunfreeman3007]

Hi Kevin fantastic video as always .all the best Shaun

[@WMCS]

Thank you Shaun 🍻

[@mickm234]

What were Ford thinking of when they built that car. Great video…

[@franciscolopezramirez3840]

Un máquina Kevin!!!

[@albertoloberza6986]

Hola Albert, mondeo complicado mucho para desarmar de ru parte impecable trabajo ..!!

[@12345678969816]

Mükembel işçilik ve ustalık saygılar takipdeyim👍😉

[@Valmo2379]

You make this look easy my man ! One question : you didn't drain the gearbox before removing the cardan shafts ?

[@peterjones035]

It’s 21:00hrs I started renewing my gearbox on the fiesta mk6 1.25 at 08:00hrs, I’m exhausted, covered in bruises and marks, got gearbox oil all in my eyes and face, all I can say is you must have arms like pop eye, oh and I had help off a second person, the clutch pedal felt a bit spongy, so should I bleed it a bit more, I did it about ten times but I lost my will to live 😂

[@LakeErieReseller]

Good work. Can you list the the equipment you use and your work chothes

[@latortue4352]

Super job 👍👍

[@Javigpfr]

Buen trabajo, yo tengo que hacer otro igual jejej

[@petipichou476]

When the clutch sender is punctured and leak fluid, is it possible to change just him by up and change just the liquid ?

[@ninrm6355]

Hi Kevin. Unfortunately you are very far from where I live…I have the clutch replaced 10k miles ago, the cylinder failed and I replaced everything again... Now after 2000 miles the cylinder failed again 😢. LUK parts all over…Is the garage doing anything wrong? Is there anything in particular to do regarding this?Please reply. Many thanks!!!

[@jerzykepinski]

this is fantastic

[@kamar317]

Very good job

[@sergserg5091]

Tell me, what kind of electric tool is used at a 90-degree angle, which you use to unscrew in hard-to-reach places? Can I link to it? Very useful video!!! Thank you!!!

[@WMCS]

Long reach Milwaukee ratchet.

[@rasputin3052]

Hi ! I always watch your videos, I can say that you are the number 1, I have to make a Mercedes vito, and I have not seen any videos. Did you share any videos about it?

[@pitupitu57]

Helo from Poland. I hawe mk3 2.0 tddi. Thanks for movie. Good luck.

[@Luton-Mick]

I had a tddi, the best diesel Mondeo they made until they stuck that crap common rail junk with playdough injectors and self destructing high pressure fuel pumps.

[@alanfrancis9225]

Just curious have you ever tried using a creeper ?. Getting on a bit myself (67) but my arms and neck ache for days after lying on back under car. Really enjoy watching your immense skills !!

[@charlesdale1462]

Great stuff. What weight do you reckon the gear box is? Back in the day our Mondeo's dmf was replaced with a solid one. Regards Charles

[@jtb52]

I kind of wonder what you do when you see all the other things that need doing on these vehicles. Even a wash would be nice for some of them

[@WMCS]

I suppose you’re just gonna have to keep wondering with Alice .. Yes I can always wash the car .. Is that your fantasy 😉..

[@andrewmount278]

She'll get her yearly wash once I've done the pads and discs later in the summer 😁

[@jlbfjonathan]

HELLO KEVIN, GOOD JOB. WHAT MODEL OF IMPACT WRENCH DO YOU USE?

[@eoghanhennessy443]

Mate i wana get the milwaukee electric ratchet im wondering what better the long reach one i do some you with or smaller one

[@northerner1374]

Skills as ever kev! Would have been interesting to do a clutch on the Subaru or mx5 in the BG 👍🏻

[@WMCS]

I’ll definitely keep an eye out for MX5 .. I’ve done one before they’re not bad at all

[@bojanlegner7051]

Is that rubber grease you're using on the input shaft and bellhousing bolt holes?

[@Navsesru]

Hello. How thick are the panels that you put under the machine while you work?

[@peterjones035]

Just a quick question please, I have installed the new gearbox on fiesta mk6 1.25, just wanted to ask if you advise back bleeding the clutch fluid or do you have any advise on best/safest way, thanks 🙏 love your videos

[@CookieScaley]

I know you want a reply from the man himself but with bleeding the clutch you can do it either way you like. I usually only back bleed if I'm having trouble getting air out of the master cyclinder

[@RK-ng1jv]

Hi, can you tell me what power/impact ratchet you use? struggling with bolts! great videos!!!

[@brianmason8400]

The big impact is an M18 fuel 1/2 drive, and the ratchet is the M12 fuel 3/8drive extended reach.....I believe on both. Kevin, my apologies if I interrupted.

[@nostraculpa0815able]

Super Arbeit! Aber so wie der Wagen von unten aussieht, müsste der mal was gegen Rost tun.

[@rimmersbryggeri]

Is this much differen drom the 2.0 petrol?

[@WMCS]

Yes … a lot more involved than the petrol ones. I think I’ll have one up on the channel soon.

[@rimmersbryggeri]

@@WMCS Thanks in advance. I have the Haynes manual fo the car but your videos are so much more instructive.

[@mickm234]

@@WMCS I shall look forward to it. My 2.0 litre Ghia needs doing. Why is a petrol one easier to do than the diesel please?

[@vornamenachname4333]

​@@WMCS i have a MK3 2006 1.8 110HP - is it really much easier like this Diesel?

[@dianadianadiana233]

Omg. That mondeo actually tired you alot. Alot of stuff needs to come out just for a clutch. Really good job kevin. Love you alot❤❤. And i want to ask a question. You now when you put the clutch on and then when you start putting the gearbox back on. When you start putting it on does the clutch inside the gearbox move when your putting it in so that the gear box sits. Like i mean when you try and put the gearbox back on. Does the clutch move by it self so that it sits even if youve titened the clutch bolts? please answer my question i really want to know❤❤❤❤

[@robertbentley4217]

Hi there I did my clutch by watching your video thank you for that but I have a little problem sometimes now when I press clutch in coming to a junction the revs will drop and car will stall will start straight up if I turn key of and on again have you ever had this problem please

[@WMCS]

Sounds like the breather hose may be loose or have come disconnected

[@robertbentley4217]

Do you mean air box sorry for been a pain

[@saulgilsenan7320]

Where'd you get that tray from Kev? That black one you stick all your bits in.

[@WMCS]

I got it from my local garden centre

[@RomanDE22]

Sehr gut

[@5tevenH]

You should get a big gazebo to work under, when it rains

[@sylwesterpachut2786]

Hello. Does the dual-mass clutch from the mondeo mk3 2.0 TDCi fit the mondeo mk3 2.2 TDCi?

[@WMCS]

I very much doubt as the crank will be of different thickness

[@arashb1758]

Eyval bro, 👌

[@aua5957]

nice work))

[@twig3288]

I feel exhausted after watching that.

[@castrolgtx5064]

Hi Kevin Question: I done the clutch in a Volvo V40 nine months ago and it’s slipping again due to a very elderly owner, would I get away with not changing the DMF ?? it has only done around four thousand miles roughly… I know you said before you change the DMF in every clutch repair or else you won’t take on the job But in this circumstances what would you do. Regards Eric

[@WMCS]

Eric in this circumstance which I’ve come across myself before .. within a year the csc had malfunctioned .. I would confidently leave any DMF Within 30k miles.. a DMF lifespan usually is between 60-80k miles for any recent cars ..

[@castrolgtx5064]

@@WMCS Thanks for the reply💥👍

[@castrolgtx5064]

@@okornel Thanks for the reply💥👍

[@ferreiramiguel2910]

what machine william you have to repair health william

[@WMCS]

Hola Miguel🍻

[@scotspie501douglas7]

OMG what a ball ache to do kevin thats why I would never buy a ford now I done a clutch on my wifes sierra years ago 10pm at night but the new fords are a nightmare

[@anthonythomas9456]

Wow definitely not a DIY job anymore is it the same as a xtype

[@WMCS]

Yes exactly the same

[@anthonythomas9456]

@@WMCS I know my way around a engine bay but I think that's too bug of a job for me u sir got some serious skills what area u cover and how much would it cost for a xtype

[@patrickmalliart5736]

Combien de kilomètres à cette auto merci

[@andrewmount278]

186000 miles, whatever that is in kilometres.

[@patrickmalliart5736]

Merci de votre réponse Cordialement Patrick.

[@dannyhazel1297]

Never again!

[@maverick507]

🙋🏻‍♂️ how are you mate?

[@WMCS]

Holla holla 😁🍻✔️

[@maverick507]

😂

[@marijanmarijan1073]

Ford's saying for Germany is - one leads away with Ford and never comes back 😁😁😁😄😄😄🤣😂

[@WMCS]

😆😂😂… oufff

[@RomanDE22]

👏

[@patrickallamani5889]

headlight bulb replacment

[@WMCS]

For sure.

[@sylos69]

Niech ktoś mi w Polsce powie, że wymiana sprzęgła to cały dzień roboty...

[@WMCS]

Subscribe to the channel for the weekly repair log. 🍻🍻🍻

[@stefandiesel9218]

What do you think about FORD ? For me they got the strangest contruktions all over! I cant stand FORD at all!!!!!!!!!!

[@WMCS]

Well the name itself gave birth to the automotive in all its aspect… so it’s come a long way from the model T..

[@stefandiesel9218]

@@WMCS here one strange example: the oilbath timing belt in the 1.0 eco boost engine! its just mad!!!

[@brianmason8400]

My opinion, ain't nothing wrong with Ford. ALL veh manufacturers have their goods and bads. Me personally, I'd take a Ford over about anything else, that's all my grandparents drove.

[@davidkidd9007]

I’ve had a lot of fords and for what you get they are value for money and pretty reliable . Imagine the cost of doing this on a German car through a garage .