2007 Toyota Tacoma Lower Ball Joint replacement

  Рет қаралды 61,089

Kimhoeun Chhay

Kimhoeun Chhay

Күн бұрын

Пікірлер
@spencerpabona5446
@spencerpabona5446 Жыл бұрын
I like this video it’s more like doing the job and talking to himself. Good job.
@adamhenderson7951
@adamhenderson7951 3 жыл бұрын
The Rooster is too much and well placed!! Great video, and thank your for getting to it and not wasting a half hour of my time with discussion about liking your channel or some other explanation of garbage!
@kimhoeunchhay4295
@kimhoeunchhay4295 3 жыл бұрын
Glad it was helpful!
@johnspanjers8321
@johnspanjers8321 3 жыл бұрын
Great video. Explained well. Thanks for that.
@Stupidspencer1
@Stupidspencer1 Жыл бұрын
I already knew how to do this job, but watched the video to see if he used any tricks to make the job easier. I didn't learn anything I didn't already know, but I couldn't help but notice the use of the impact driver to torque all the bolts during reassembly. I'm sure that impact driver is every bit as accurate as a torque wrench, right? HA! If you've never snapped a ball joint stud, then you wouldn't realize the importance of not over-torquing them. I have had one snap while on the freeway and it almost cost me my life. Its fine to follow this guy's procedure, but I would highly recommend using a torque wrench to tighten each nut to its specified value during reassembly.
@Zimbob2424
@Zimbob2424 11 ай бұрын
thanks , good to know. I had a tie rod snap about 35 yrs ago and very lucky to have survived.
@chente0359
@chente0359 Жыл бұрын
Amigo soy de México, no entiendo mucho inglés pero está perfecto tu procedimiento, me ayudó mucho con una Tacoma, realice el mismo trabajo guiandome con tu vídeo, muchas gracias
@edwardnoyola2860
@edwardnoyola2860 Жыл бұрын
I’m glad I watched this video. Was very helpful and made me laugh at times. Made my day!
@ravenfeather7087
@ravenfeather7087 Жыл бұрын
Same here. It was a joy to watch.
@johnneil6501
@johnneil6501 3 жыл бұрын
Good video, real world replacement.
@jasonpleasants476
@jasonpleasants476 Жыл бұрын
Good walk through! Very helpful.
@ravenfeather7087
@ravenfeather7087 Жыл бұрын
Nicely done. Thank you.
@AhThizz
@AhThizz 3 жыл бұрын
This video helps so much on what I have to do when I lower my 05 tacoma
@shortydancer
@shortydancer Ай бұрын
thanks for the video. I think I might just buy the whole lower control arm assembly though lol
@juvenalalvarez9535
@juvenalalvarez9535 2 жыл бұрын
Great job. Thaks for Sharing your experience. from Atl Ga.
@hernandezgilbertojose6342
@hernandezgilbertojose6342 Жыл бұрын
Excellent my friend just need change tacoma 2001
@davonriver25
@davonriver25 3 жыл бұрын
Very helpful! Love the rooster 😂
@kimhoeunchhay4295
@kimhoeunchhay4295 3 жыл бұрын
So glad!
@northinstruments3304
@northinstruments3304 3 жыл бұрын
I like your no nonsense method and tool description. thanks! Will you do the uppers?
@kimhoeunchhay4295
@kimhoeunchhay4295 3 жыл бұрын
Yes I will
@737mechanic
@737mechanic 10 ай бұрын
I like this guy. Subscribed.
@brendanphilbrick301
@brendanphilbrick301 2 жыл бұрын
Banged one out today Sir! I had more things fighting me that’s for sure. But i persisted. Now to do the other side.
@kimhoeunchhay4295
@kimhoeunchhay4295 2 жыл бұрын
You got this!
@brendanphilbrick301
@brendanphilbrick301 2 жыл бұрын
@@kimhoeunchhay4295 yeah! I got the other side done as planned. I was way faster disassembling. However i had a issue with cup size removing a joint that was not oem and had a slightly larger shoulder on the ball joint. I had to grind both the ball joint flange and the socket to fit! 😉
@tanhvan1
@tanhvan1 2 жыл бұрын
Why not torque the bolt to the manufacturer specifications?
@TBr0III
@TBr0III 2 жыл бұрын
Thank you for the video Sir!
@kimhoeunchhay4295
@kimhoeunchhay4295 2 жыл бұрын
My pleasure!
@shoeboxford9932
@shoeboxford9932 3 жыл бұрын
Very informative! Thank you.
@kimhoeunchhay4295
@kimhoeunchhay4295 3 жыл бұрын
Glad you enjoyed it!
@glenncarla18
@glenncarla18 4 ай бұрын
What size adpater did you use? I can’t find the correct size its either they’re too big or too small
@killahjeep
@killahjeep 2 жыл бұрын
you dont need to remove the axle shaft, tie rod, or the swaybar link.. just remove the lower strut bolt, the 2 lower knuckle bolts (19mm), and then you can mark & loosen the LCA bolts to swing it lower.. and get a press on the ball joint.
@chrisharris7783
@chrisharris7783 2 жыл бұрын
That's what I was thinking as I just replaced struts not to long ago. I'm getting ready to change ball joints soon so it's good to see your comment as I didn't see the need to remove everything else as well.
@glenwhitestofer6420
@glenwhitestofer6420 2 жыл бұрын
I just removed the axle bolt and 2 lower knuckle bolts swung it out of the way and used ball joint press, no need to lower control arm
@Sqwrly10
@Sqwrly10 Жыл бұрын
Freeze the ball joint before hand and it goes in easier too
@AaronLives34
@AaronLives34 Жыл бұрын
When you say mark and loosen the LCA bolts why do you need to mark them? I'm learning to do this job so asking all the questions lol
@killahjeep
@killahjeep Жыл бұрын
@@AaronLives34 it's so you can get the alignment close to what it was before getting the truck to an alignment rack. You mark the position of the cam bolt relative to the mount. You may see there are already markings on the bolt head & bracket..
@joereyna614
@joereyna614 Жыл бұрын
Is it just me or is that Bilstein shock crooked @22:26?
@carlosmoreno2387
@carlosmoreno2387 Жыл бұрын
You’re awesome 👏 a real master mechanic
@khimsannsoy3587
@khimsannsoy3587 6 ай бұрын
អគុណណាស់
@nasseralnasser9101
@nasseralnasser9101 2 жыл бұрын
احسنت , عمل جيد.
@mariomata9177
@mariomata9177 Жыл бұрын
How did you replace the top ball joint ?
@joereyna614
@joereyna614 Жыл бұрын
This is something I need done but 1) don't have any of the tools and 2) it's hard to find a knowledgeable mechanic near me.
@SteveInterdonato
@SteveInterdonato Жыл бұрын
excellent
@bh3945
@bh3945 3 жыл бұрын
Great video.
@kimhoeunchhay4295
@kimhoeunchhay4295 3 жыл бұрын
Thanks!
@2jzgabe868
@2jzgabe868 2 жыл бұрын
Would this be the same for a 2015??
@rjswallows
@rjswallows Жыл бұрын
Yes, same setup
@Offgrid4x4
@Offgrid4x4 Жыл бұрын
Ah thanks guy
@robertmixon8160
@robertmixon8160 3 жыл бұрын
Great job. I know it would be much easier if your vehicle was on a hydraulic lift :-)
@kimhoeunchhay4295
@kimhoeunchhay4295 3 жыл бұрын
Very true!
@tyzok23
@tyzok23 6 ай бұрын
You don't have to remove the cv axle
@moondog8072
@moondog8072 2 жыл бұрын
Nice video! I did notice that you didn't put the rubber dust boot on the ball joint. Did the kit not come with one?
@glenwhitestofer6420
@glenwhitestofer6420 2 жыл бұрын
If you notice the black rubber around the new ball joint stud that is an integral boot,nothing else required
@captnmack747
@captnmack747 2 жыл бұрын
Good video, I would have cleaned surface and greased mating surface..
@Si1entKiller99
@Si1entKiller99 2 жыл бұрын
what size receiving cup did you use to pull the ball joint out ?
@elgatogordo9523
@elgatogordo9523 2 жыл бұрын
Same here! I have a cheap ball joint puller kit and don’t have the correct size to remove the ball joint 😩 Only to install it 👍
@mattb6118
@mattb6118 Жыл бұрын
I did not have the correct size either, very frustrating!! Had to put it all back together with out finishing the job!
@68M35A2
@68M35A2 Жыл бұрын
@@mattb6118 Did you find out the correct receiver cup? I'm still looking for one.
@glenncarla18
@glenncarla18 4 ай бұрын
Oh wow not only me. Please need answer for this
@alfredbernal8603
@alfredbernal8603 3 жыл бұрын
How come no torquee? I'm afraid it might be too tight or not too tight for your best customer? Also, i know what to buy you for Christmas...magnectic bolt dish holder.
@kimhoeunchhay4295
@kimhoeunchhay4295 3 жыл бұрын
Thanks for the tips!
@adrielian5077
@adrielian5077 3 жыл бұрын
Where is your shop located?
@kimhoeunchhay4295
@kimhoeunchhay4295 3 жыл бұрын
My shop location in Lowell Massachusetts
@SmokinZen
@SmokinZen 11 ай бұрын
Wish I could find a good mechanic
@fknwayne_
@fknwayne_ 3 жыл бұрын
Great video! By any chance do you know what size cups you use to remove and install the ball joint? I rented one from autozone but don't have the right sizes. Thanks
@sonrt2107
@sonrt2107 3 жыл бұрын
Would just buy one from Amazon, about the same thing. The charge extra for the adapters with and c clamp.
@kimhoeunchhay4295
@kimhoeunchhay4295 3 жыл бұрын
Hi, Wayne Pascual How are you? I used Snap-on BJP1 Master ball joint . I did not remember the cup size. Thank you so much for watching my video. Thank you Kim
@jsol2480
@jsol2480 2 жыл бұрын
Funny guy
@kimhoeunchhay4295
@kimhoeunchhay4295 2 жыл бұрын
Thank you for smiling
@jhonnyestuardo54
@jhonnyestuardo54 Жыл бұрын
Overfill without boot 😂😂😂😂😂 no way 😢😢😢
@sleeks9939
@sleeks9939 3 жыл бұрын
Khmer?
@kimhoeunchhay4295
@kimhoeunchhay4295 3 жыл бұрын
khmer bart
@sleeks9939
@sleeks9939 3 жыл бұрын
@@kimhoeunchhay4295 Are you Cambodian?
@kimhoeunchhay4295
@kimhoeunchhay4295 3 жыл бұрын
I am Cambodian How can i help you ?
@lh98
@lh98 2 жыл бұрын
@@kimhoeunchhay4295 Phnom Penh Asian grocery store in Lowell. Haven’t been there in at least like 15 years might not even be there anymore...always ate Pho 🍜 in the Vietnamese restaurants when I was there. Married into the Thai Lao folks so eating pho there and getting Asian groceries was a necessity. ✌️
@defectahz6399
@defectahz6399 Жыл бұрын
You will need an alignment after you loosen the cam bolt. I don’t care how close you get it to the “mark”
How To  Replace a Lower Ball Joint on a 2002 Toyota Tacoma
18:52
lowrangeoffroad
Рет қаралды 288 М.
How to Rebuild the Entire Front Suspension in your Car or Truck
23:17
How Strong Is Tape?
00:24
Stokes Twins
Рет қаралды 96 МЛН
REAL or FAKE? #beatbox #tiktok
01:03
BeatboxJCOP
Рет қаралды 18 МЛН
Toyota Tacoma Ball Joint Replacement (the easy way, trust me!)
21:21
The Joy of Wrenching
Рет қаралды 24 М.
How My Toyota Balljoint Failure Almost Killed Me ...
19:13
Nathans Porsche Workshop
Рет қаралды 206 М.
Top 5 reasons why the suspension knocks | AUTODOC tips
8:14
autodoc.co.uk
Рет қаралды 1,5 МЛН
Why Not to Buy a Cheap Quick Strut Assembly for Your Car
6:49
Scotty Kilmer
Рет қаралды 3,2 МЛН
5 Symptoms of a Bad CV Axle
3:31
FixIT
Рет қаралды 47 М.
Toyota Tacoma lower ball joint replacement (reinstallation)
16:46
The Joy of Wrenching
Рет қаралды 13 М.
Clunking in the Front? What's That Noise in My Car, SUV, or Truck?
5:28
1A Auto: Repair Tips & Secrets Only Mechanics Know
Рет қаралды 2,3 МЛН
When Should You Replace Toyota Struts and Shocks? And How to Do It!
30:44
The Car Care Nut
Рет қаралды 1 МЛН
How to check lower ball join play
14:21
Toyota Maintenance
Рет қаралды 38 М.