2008-2012 Escape Remote Start Installation

Brad shows you how to install an MPC remote start kit on a 2008-2012 Ford Escape
To skip the intro and go straight to installation, go to 4:30
Link to purchase this kit below👇
shop.mypushcar...

[@--greg]

I ordered this kit and the installation was easier that the video. All you have to do now is unplug all harnesses and insert into theirs. No splicing of wires period. The installation instructions say to cut a wire and tape both sides but I pulled it out of the connector on one side then taped the other. I did not have any kind of switch like this one did. It was just the basic one on Amazon. I just installed it and pressed lock-unlock-lock and the vehicle started up (2012 Escape). So far seems easy, just hope it's a lasting piece of equipment. We got this because we started having the issues that these have to where they won't start but come on. Hopefully this is the fix 😁

[@oldfreddyfrenchfry1]

Thanks for the video! I installed without any issues. You do need 2 “different” OEM keys (ie, not a cloned copy.) around $300 for the key and programming at Ford dealer. Mother OBD plug doesn’t fit in my car’s mounting clip, so it just dangles from a zip tie - a small bummer. I had to pay careful attention packing the wiring around the steering column. Some are pretty tight, and you don’t want the adjustment lever pinching them. Go slow, and treat it like a puzzle to find the best placement. If I push the buttons too fast, it won’t start, so wait a quick potato between presses. When you get in, don’t push the brake before putting the key in run. And you need the key in run position to unlock steering wheel and stop the brake pedal from turbo the car off. The harness has wires already for an “add on pack” to install a separate remote or mobile app function, if you decide on that later.

[@dominicshelley1092]

I have a 2012 escape can u post the link

[@Fskelton]

Well Done, I have A 2012 Ford Escape as well. (I'm a little nervous about Splicing) but you made it look pretty easy (I assume you disconnected the battery?) Also What Stereo do you have?

[@DTFGarage]

I actually didn't disconnect the battery, probably a good idea to do so though. The quick splices I used are pretty easy to work with and easily reversible too. The stereo is a Kenwood that I purchased back in 2013.

[@AlvinSonier]

@@DTFGarage where do you get the stereo faceplate to fit double din head units? :). Love your video I’m gonna order the starter for my 2011 Escape :) thank you!!!!!! 😎 mine doesn’t have keyless entry where it’s a XLT but I’m sure the kit should still work :) ?

[@jenkinsspeedshop]

ive got a very similar kit on the MK3, absolutely worth having +100

[@gabeulrickson2496]

Do they not sell the system anymore, website doesn't show any escape on the "find a remote start system for your vehicle"

[@DTFGarage]

Looks like they finally have the kit back in stock now.

[@balbutie]

I dont have a car but it was very interesting🛻🛻🛻

[@chriscamarillo4616]

Will it work on the hybrid models?

[@robertfant4628]

That was the cool as hell

[@kyleheroff6475]

Do I need 2 factory fabs or just 2 factory keys? I have 1 factory fab and 1 factory key and the remote starter came with 2 fabs. I'm installing an Idatastart RF3462AE into 2009 Ford Escape. I can get the lock and unlock to work, but not the remote starter feature. Other videos mention the need of a hood pin and you also talked about a valet switch. In the owners manual I see a valet mode, are those two different? Sorry to unload all these Questions, just trying figure this all out.

[@geraldwhite2912]

I bought the kit installed it works flawlessly. But do you know if you buy the flash link can you change the settings so the seat warmers come on?

[@DTFGarage]

That I am not sure about, you'd probably have to get ahold of MPC to confirm that info.

[@cardriver1588]

I have a 2008 Ford Fusion se

[@mainormelgar8274]

Hi. I have a question. If anybody could help me out would be great. I have the same module but when i connect the 4 pin data. The 3 lights start flashing without stop. What could it be?

[@terryjandt5406]

I have a 2011 ford escape do you have the brand or model number, I need to get the same one

[@DTFGarage]

It was MPC part number B-4368-209

[@silvajuan8968]

What happens if a don't cut the wire?

[@DTFGarage]

That's a good question, I'm really not sure. It probably just wouldn't work.

[@DTFGarage]

Hi everyone. As of right now MPC is out of stock for these remote start kits. They are expecting to have more in stock around April 2022.

[@judahisrael9456]

Hello…Quick question you said you have to have two keys…so do both keys have to be the keys with the lock and unlock buttons on it or can it be one key with the lock and unlocks buttons and the other key just be a plain factory key without buttons ?

[@DTFGarage]

@@judahisrael9456 the keys don't have to have the buttons on them, they just need to be able to start the car.

[@judahisrael9456]

@@DTFGarage thank you 🙏🏾

[@melissarochester342]

Ok I have a 06 dodge charger that my wcm module's antenna broke so I got another from a used car and model by can't seem to get it programmed since it's a different vin #... will this type of remote start work to get my car started??

[@carlosbasantes1091]

hello friend I saw your video and I tell you something it's very good I liked the credits at the end very funny and it's a very good video I already subscribed and I hope to see more like that ... my question is could you tell me what the kit is called on Amazon could you give me the name I have a Ford escape and I would like to be able to install it I am Charly from Massachusetts thanks for your collaboration

[@tommyd1399]

tried to purchase a kit for my 2011 escape and they tell me they don't make one for that application or for the 2012 with makes no sense cuz i just watch this

[@jessiperry60]

someone that has money to spend had them installed for 1000 or 1200.. remember its easy to say dont buy a brand new car it will depreciate but its only people that cant afford it that say that kinda stuff.. you only have 1 life enjoy it while you can

[@DTFGarage]

I checked MPC's website and it looks like they finally have the Remote Start Kit back in stock for the 08-12 Escape!

[@robertboy25]

I can't find it on seller's web, i have a ford escape 2011. Can you tell me where to buy it?

[@MisterRubenJr]

Thanks!! Just got hold of an older low miles escape. You made this a cinch. :). Thank you.

[@Evan-bv8bh]

What do you do if you don't have the same matching color cables but everything else seems to be the same. I bought an Evo-all kit for 2011 Escape

[@federicoperez9538]

New here! Would this happen to work with the escape's cousin the mercury mariner?

[@joejoe8831]

Question, are these kits are for no crank no start for Ford escapes ?

[@leom5336]

Just installed mpc 2008 ford escape. Love it but can't shut my car off .I have to turn it of with remote. Any suggestions??

[@DTFGarage]

You can push the brake pedal to shut the engine off once it's been remote started. If you've gotten in the car and turned the key to the "on" position, you should be able to turn it the "off" position to shut the engine off.

[@kdnichols99]

Quick question, that first part where you plug into the ignition/key area, that is the bypass and is included in the kit?

[@DTFGarage]

Yes that is included with the kit

[@RediscoverLostKeithWille]

Where did you purchase those wire splicers? What type are they?

[@gabeulrickson2496]

Only other question, if you press the brake pedal without the key in the ignition will it shut the car off?

[@mainormelgar8274]

Yes.

[@DTFGarage]

Hi everyone! I apologize, the original link was broken and was removed. I have updated the description with the new link for the kit.

[@IAmMrTrumpet]

Escape is not an option for 2012 Ford from what I’m seeing on that link.

[@ajamesbertman]

@@IAmMrTrumpet I noticed the same thing. If anyone has a fix, let us know.

[@scottkeyser3785]

3 years later , I just installed the same kit. Some updates the data link is now plug and play . Works great easy install . Thanks your video made my decision which brand to buy .

[@DTFGarage]

Glad to hear it helped! I'm about to buy another one for my wife's 2011 Focus

[@pixilatedshots7569]

Link please to purchase

[@BrendanOpgaard]

Thank for posting this. I followed along and successfully installed this today on my escape. When programing I made a few errors, but I finally got it worked out and programmed! Just out of curosity, why is it that the OBD connector needs to be spliced into? what is the purpose?

[@DTFGarage]

Glad it helped Brandon! The reasoning for it being spliced into the CAN-BUS wire on the OBD plugin is so that the module can pick up when the car is bring locked or unlocked so it can start the vehicle. In older vehicles without CAN-BUS you have to splice about 30 wires so the remote start module will work properly.

[@omarnunez2788]

Hi do you know about a kit that can be installed if I only have one key? Thanks. Loved your video.

[@KarlGPhoto]

I’m in the same boat and don’t want to spend close to $200 at the dealership to get a second key made. Unfortunately I haven’t found anything that can be programmed with only one key.

[@DTFGarage]

I am not currently aware of a kit that can be done with just 1 key, but I would check with your local locksmith. They can usually program a true 2nd key, and it's much less than at a dealership.

[@nathanp8509]

What other kits do you recommend? Can you recommend any that are two ways?

[@felixrios4679]

you could put the links where you bought the materials

[@DTFGarage]

Hi, the original link I had was broken. Updated with new link to the part in the description.

[@romoguy91]

After you remote start it's and get inside the card do you have to put the key in and turn it to the on position, or how does it work?

[@DTFGarage]

Yes, once you get in the car you'll have to insert they key and turn it to the on position to drive the car.

[@noblewv70]

I ordered this same kit for my 2010 Escape. I planned to follow your video and install it myself. It seems like a very easy install except for tapping into the 2 CAN wires behind the OBD connector. When I asked MPC if I could use T-taps, they told me to never use taps on CAN wires. Is everything still working correctly with your install? I don't know whether to go ahead and try to install it or send it back and forgot about it.

[@DTFGarage]

It's been almost a month and I remote start it almost very day. Haven't had any issues yet.

[@noblewv70]

@@DTFGarage Thanks. I think I'm going to try installing it.

[@ALIENsosa]

@@DTFGarage what size gauge t taps did you use for obd?

[@ac28loaiza3]

good video!!

[@raoofsayad461]

Hi bro were can I buy this kit. I need it for my bro.

[@DTFGarage]

Added new link to the description

[@raoofsayad461]

@@DTFGarage thank you.

[@geraldwhite2912]

How long does it stay started for?

[@DTFGarage]

It will run for 15 minutes before it automatically shuts off.