How to install a stereo & speakers in a 2008-2012 Ford Escape | Crutchfield video

[@dontcareisaidit]

Thank you, was watching 8 minutes into someone else on here and they say "this wouldn't be hard for someone who knew what they were doing but this is my first time" and I think I blacked out on some rage induced triggering, then found yours. Idk wtf some content creators are doing on here.... Making tutorials the first time they try doing something themselves? I'll be lucky I get this right with this video lmao Don't ranting, thanks for a precise and functional tutorial (i just looked and they got more likes than your video, wtf??? that's unfair af)

[@crutchfield]

I am stoked to hear you found the video helpful and I hope it helped you get installed! Keep us posted on how it goes.🥰

[@dontcareisaidit]

@@crutchfield got a bad wire harness from red wolf... lesson learned. cost me a new stereo i kinda wanted figuring my old one crapped out in storage (dual, never a long term brand imo). Once I got the harness that works i'll be fine. Never had a bad harness so it threw me for a loop for two days. Had me questioning my vehicles wiring lol got a tester now so never again.

[@crutchfield]

You live, you learn. Or in this case, you attempt, test, and you learn lol

[@DanielGennaro]

Love you crutchfield!! Been using you guys for years. I’m sure it’s hard to compete with Walmart and amazon but I hope you can still remain competitive. I’m sure it’s not been easy.

[@austinzimblis8396]

thank god someone finally made one.

[@tatsumaru12345]

The non nav versions dont have the 4 screws. The holes there aren't even threaded. Pissed me off so bad, new radio working and everything. But scoches kit is essentially a nav radio replacement only. You can use bolts/nuts, but good luck getting the alignment right, and it's a pain to remove if you need to.

[@ekfinn]

Heads up for folks with Microsoft Sync. The CAN network adapter that interfaces for the steering wheel controls will not port the voice command, OK, and phone answer/hangup buttons.

[@seangowan7441]

Does this car have the factory SYNC?

[@moto157droid]

will the Ford sync system still work ? and in my wife's 09 escape what happens to the info panel above the factory non nav head unit ? The panel that show ALL the info ?? will it just be useless? If so, if I use the Maestro add on will that panel and sync system still work? Thank you in advance

[@crutchfield]

The SYNC system can be kept working with the right type of aftermarket radio when its installed with the proper parts. A receiver with an iDatatlink port on it and then using the iDatalink Maestro ADS-MRR interface can keep it working. The stock display will not be used anymore as this setup allows the new radio to display that information. For additional assistance & personalized recommendations, feel free to contact us directly: www.crutchfield.com/I-rYTVc000/ContactUs.aspx I hope that helps. --Crutchfield

[@zacherydonahue8346]

Do you guys got a link for a wiring harness that will fit my 08? I’ve been looking everywhere and can’t find one

[@crutchfield]

Depending on which factory trim package came in your Escape originally (factory navigation, subwoofer, basic, etc.), a different vehicle integration harness model may be recommended. Regardless, we should have a harness that will work for you. For additional assistance and personalized recommendations, feel free to contact us directly by phone or through our online chat service: bit.ly/2jBGHPp Hope that helps. --Crutchfield

[@Arvisgrt]

Which wiring harness do i need to buy, and if i use the one you used, do i need to still run the redwire to a switched 12v or will the module take care of that for me ?

[@ChristopherTradeshow]

oh lmao I was on the website for this company and wanted to know how to install one XD this is the best

[@moralesruben974]

how much will be the cost of the stereo and cover where you can buy greetings

[@crutchfield]

Hi Ruben, We would love to help you out with an upgraded stereo setup for your vehicle. Please get in touch with us! A member of our Advisor team will be happy to go over stereo fitment for your vehicle, and build a cart for you with the installation gear you will need for the complete install of your new stereo. www.crutchfield.com/I-rYTVc164/contact

[@8man13]

this helped a lot but i was hoping to find some video to replace the backup camera ... please

[@crutchfield]

This is our video on installing a backup camera: www.crutchfield.com/I-rYTVc974/learn/video-how-to-install-a-backup-camera.html We have a lot of other helpful articles and videos you might like to check out as well. You can type in what you're looking for and if we have a video or article on it, you'll find it here: www.crutchfield.com/I-rYTVc974/Learn/

[@dubiousjesse]

Where is the sirius antenna connection located? I have the XLS model with the sirius button but no antenna.

[@crutchfield]

If present the factory XM antenna connection is on the rear of the factory radio. You'll need the SiriusXM tuner in the first link below when installing any XM Ready aftermarket radio. If you have a factory XM antenna in your 2008 Ford Escape, you can also use the iDatalink SAT2 adapter to use the existing factory XM antenna with your SXV300V1 tuner. www.crutchfield.com/I-rYALc166/p_220SXV300/SiriusXM-SXV300V1-Tuner.html www.crutchfield.com/I-rYALc166/p_794ANTSAT2/iDatalink-SAT2-Satellite-Radio-Antenna-Adapter.html

[@underground27]

I have a 2008 Ford Escape. No navigation. However, I would like to retain accessory power. 2 harnesess comes out the radio. Will I still need to buy this particular harness with the module?

[@crutchfield]

The beset bet at determining what you will need will be to talk to an advisor: bit.ly/2KP1zS3

[@michaelyoung394]

With this radio install, do you retain compass, and exterior temp on center stack?

[@crutchfield]

The clock and compass will still be shown but any stereo information (like the radio frequency) will no longer be displayed.For additional assistance and personalized recommendations, feel free to contact us directly: bit.ly/2jBGHPp Hope that helps.--Crutchfield

[@javierortiz7535]

2008 Mariner Hybrid Would i loose the Hybrid information that my OEM radio shows?

[@crutchfield]

That information should not be lost. There is a display at the top of the dash should continue to work and show that information.

[@javierortiz6116]

@@crutchfield I meant to say the Hybrid info that is currently displayed in the double din screen OEM? Ie: MPG, hybrid battery state of charge, battery current flow from engine to wheels Batterry and such, this info is collected from the car via can, will your device display this NOT the information above the vents

[@nickmackay]

i have a 2011 ford escape and people are saying i need the maestro ads-mrr module to replace my radio....as far as i can tell this is only to maintain the SYNC functions, which my car already DOES NOT have...my question is that in order to keep my steering wheel controls (volume, forward/back, etc.) do i still need this module? (also fyi the sony head unit I am planning to purchase specifically says that it supports steering wheel functions)

[@crutchfield]

We have a few other wiring harnesses available to help install a new radio. I recommend contacting an advisor to discuss your specific Escape and the options you want to keep to get a personal recommendation on the wiring interface to use to install your Sony. Here's how to reach us for this help: bit.ly/2xOOeQR

[@jennifertan900]

I have Sirius radio packaged with my escape. WilI lose this if I upgrade to a double din?

[@crutchfield]

We can check. What is the year of your Escape?

[@jennifertan900]

@@crutchfield 2011 Ford Escape XLT

[@crutchfield]

It looks like the factory version of SiriusXM will be lost when changing the receiver. The good news is you can get a new receiver that is SiriusXM-ready, pair it with the tuner, and keep it that way. I see that we have adapters for most versions of that vehicle to retain use of the factory satellite radio antenna. If we can help choose a receiver and the necessary installation gear, reach out to an Advisor any time. Here is our contact info: www.crutchfield.com/I-rYTVc313/support/ContactUs.aspx

[@sawatzky9412]

if i get the wiring harness, do i still need to hardwire the stereo to the parking break?

[@crutchfield]

It depends on the wiring harness available for your specific vehicle and the wiring in the vehicle too. Some of the harnesses include the parking brake wire and some don't depending on the car. What's the year, make, and model of your vehicle?

[@sawatzky9412]

@@crutchfield 2012 Ford Escape XLT without factory Sub and Without Nav.

[@crutchfield]

We do carry harnesses for your Escape that don't require you to hardwire the parking brake wire. Do you have a particular radio in mind?

[@lyttrob5252]

can i call and get all that i need to change the stereo or do i ahem to buy things like the stereo somewhere else. (very informative thank you)

[@crutchfield]

+Robert Lyttle We sell the stereos and the parts to install them into these Ford Escapes. Feel free to contact us directly: www.crutchfield.com/I-rYTVc000/ContactUs.aspx I hope that helps. --Crutchfield

[@lyttrob5252]

thank you for the info guys and girls. i have to talk to my wife and see if I'm allowed hahha

[@Muhyedinschannel]

Crutchfield what’s the harness you have used to connect stereo to the car thanks

[@crispalacios3635]

Can a reverse camera be integrated into that system?

[@crutchfield]

A reverse camera, also called backup camera, can be installed into this vehicle and connected to any touchscreen receiver with a backup camera input (should be most, if not all receivers with a touchscreen now).

[@MrRaydog1]

My brother has cut the factory wiring harness from my 2009 Ford Escape trying to install an aftermarket stereo!!!! Any idea which wire in my Ford is the auxiliary wire to connect to the new stereo??? Can't find any wiring diagrams online.

[@crutchfield]

The best solution will be to re-attach the original factory harness plug and use a proper vehicle harness to connect the new stereo to the factory connector.You can find the proper vehicle harness for your install by using the "Outfit My Car" application on the main Crutchfield website: bit.ly/2l32bTh For additional assistance and personalized recommendations, feel free to contact us directly: bit.ly/2jBGHPp Hope that helps!--Crutchfield

[@MrRaydog1]

Well, that would be ideal, but he can't find it. So you don't know which wire is the auxiliary?

[@fixinggrace]

You may need to go the junkyard to find the harness.

[@Mr_Meowingtons]

@@MrRaydog1 go to the junk yard and cut one out

[@likatchkadua3353]

i purchased boss BV9358B stereo and ascw-1 steering wheel ampifier for ford escape 2010, steering wheel inferface doesnt work, what recomendation for steerine wheel inteface module???

[@crutchfield]

So sorry to hear that you're experiencing trouble with your connections. Unfortunately, Boss receivers typically do not work with steering wheel control interfaces or adapters. You may want to reach out to the technical support team of the vendor you purchased your gear from for further assistance.

[@manuelforero2116]

I have the same problem with this radio. Also clock in central panel is no working any more.

[@susannahdavis5291]

How hard is this for a novice? I am the type to try things and the cd drive is broken and I wanted to replace that part.

[@crutchfield]

We do everything we can to make it as easy as possible, but it does depend somewhat on your vehicle. One of our advisors would love to gov over the process and explore your options! bit.ly/2KP1zS3

[@lmbear]

This receiver doesn't look like an upgrade to the factory navigation system.

[@M0N0T0N0US]

Factory navigation is crap!

[@jonathanspindler]

I have a 2012 Ford Escape limited, the factory display shows both radio info and full climate control info ( fan speed,interior dual climate temps, exterior temp,compass) .....will my climate control display still work fine after I install an aftermarket head unit?

[@crutchfield]

Yes. The radio information will no longer show on the stock display but the climate control, temp, compass and clock will remain.For additional assistance and personalized recommendations, feel free to contact us directly: bit.ly/2jBGHPp Hope that helps!--Crutchfield

[@Muhyedinschannel]

Crutchfield what’s the stereo model number

[@Onyx408]

With new receiver does it do car play? And does it still show the battery system for the hybrid model?

[@crutchfield]

Hi CJ, do you have a specific model radio in mind? To verify, you have the 2008 Ford Escape hybrid? Did it come with factory nav?

[@1notgilty]

Thanks. Very informative.

[@TheLunarFX]

do the steering wheel volume controls still work?

[@crutchfield]

The factory steering wheel radio controls can be retained with the proper installation accessories and a compatible aftermarket stereo, yes.You can view all of the models we recommend to fit your Escape by using the "Outfit My Car" application on the main Crutchfield website: bit.ly/2l32bTh For additional assistance and personalized recommendations, feel free to contact us directly: bit.ly/2jBGHPp Hope that helps.--Crutchfield

[@ogopogo1397]

the adapters they sell are cheap quality and leave a best behind the unit. Would be better if they just said what colour goes to what fir hard wiring IMO.

[@gabeulrickson2496]

@@ogopogo1397 can't hard wiring steering wheel controls nor can you hard wire a 12v ignition with the retained accessory capability without cutting the 87 pin for the delayed accessory relay In the fuse box located in the passenger floorboard

[@TheFreeman1979]

when you install the new radio were you able to use steering wheel to control the new aftermarket radio. I have ford escape 2010 and I will be installing aftermarket JVC. I was told I cant use the steering wheel to control the radio no more.

[@crutchfield]

The factory steering wheel radio controls can be retained with the proper installation accessories and a compatible aftermarket stereo. Most JVC models will be compatible not all. For additional assistance and personalized recommendations, feel free to contact us directly by phone or through our online chat service: bit.ly/2jBGHPp Hope that helps! --Crutchfield

[@TheFreeman1979]

But do you think even after installing the jvc radio can I also be able to use the factory aux.

[@crutchfield]

@@TheFreeman1979 There are a few JVC receivers that when installed into a 2010 Escape using the proper gear, will be able to keep the use of the AUX input. I recommend contacting an advisor to discuss the specifics of our Escape, JVC model, and see if there is any install gear that will let that AUX input work with it. Here's how to reach us for this help: bit.ly/2jBGHPp --Crutchfield

[@nickmackay]

so im finding everywhere that 6x8 is the stock speaker size in my 11 escape, will 6x9 fit as well or is that actually too big for the door mounting holes?

[@nickmackay]

or should i use these www.amazon.com/JBL-GTO8629-Premium-Co-Axial-Speaker/dp/B00881CT2K/ref=sr_1_11?s=electronics&ie=UTF8&qid=1542142096&sr=1-11&keywords=6x8+speakers instead of the 6x9 model?

[@nickmackay]

main reason i had wanted the 6x9 was because they were 3 way, whereas the 6x8s are two way....although it does look like this model of 6x8 can out perform the jbl 3 ways as well but i wasnt sure if the 6x9 would even fit or not

[@crutchfield]

6x9 speakers do have mounting tabs that are spaced further apart than those on a 6x8 speaker. Also, the 6x9 is a bigger speaker. We have not researched the vehicle to see it there is a way to modify the mount to take a 6x9 speaker. I recommend consulting a custom installer to see if its possible to make that change. Good luck!! --Crutchfield

[@theroguenob]

Can you give me the direct link to that speaker, your website is a little difficult to navigate and find that specific stereo

[@crutchfield]

This video is more about the specific vehicle installation and not the aftermarket stereo and speaker models. The video was posted in 2015 so, the stereo model has since been discontinued.You can view our current selection of JVC DVD receivers on the main Crutchfield website here: bit.ly/2k9AA4j For additional assistance and personalized recommendations, feel free to contact us directly: bit.ly/2jBGHPp Hope that helps!--Crutchfield

[@FabiolaDevanny]

+Crutchfield My friend I have a problem with my ford escape, I've been robbed the dvd/gps and cut all harness cables, unfortunately I do not have the wiring diagram to verify the colors and their order, by chance you will not have the diagram that you can sell me Or maybe you can give me photos of harnesses and pacifiers where you can see the cable one by one and color by color so I can mount another stereo. excuse me for my bad english i'm write from mexico

[@saulchmxd]

what is the size of the speakers

[@crutchfield]

+saul chm 6x8" is the factory size in both the front & rear door locations. You can find all of the speaker models we recommend to fit each location by using the "Outfit My car" application on the main Crutchfield website: www.crutchfield.com/I-rYTVc180/car/carselector.aspx?lp=%2fCar%2foutfitmycar%2fcar.aspx Hope that helps!--Crutchfield

[@saulchmxd]

thanks

[@Muhyedinschannel]

Crutchfield what’s the size of the radio

[@masterberkant]

Mine iş hyntid,if i upgrade mine, still can i use adn see hybrid information (like mpg exc) on the new entertainment system?

[@handicapitation3250]

The way this video was edited is pretty bad. The camera view should just be focused on the work being done, with just the audio from the creepy guy narrating. Why show his face? He's not even working on the vehicle and his face bugs me out. haha btw I still "liked" the video. Got the information I needed. thanks!

[@rodger6940]

Crutchfield, I have a 14 scape I want to upgrade my front and back door speakers for something little louder, I would like to buy it from you

[@crutchfield]

For personalized recommendations & assistance, feel free to contact us directly: bit.ly/2jBGHPp Hope that helps!--Crutchfield

[@uroverrated69]

Question, will this setup still allow for the rearview camera to display when the car is in reverse, and proximity sensors? Or do I need to go straight to Ford for a replacement like that?

[@crutchfield]

Hi Omar! Those features can be retained with some vehicles depending on the wiring harnesses, adapters and interfaces available for the vehicle, and the compatibility of those harnesses with the stereo you have chosen. Reach out to us by phone or online chat! A member of our Advisor team will be happy to go over your vehicle's information, answer questions, give you personalized advice and recommendation, as well as go over the products needed for your install! www.crutchfield.com/I-rFBKc164/contact

[@NetSloff]

Why can't we disconnect airbag?

[@crutchfield]

Disconnecting that harness can cause issues with the airbag control system so that it throws a fault code to the BCM which disables airbags from deploying in the event of an accident. Best to keep the airbag harness plugged in.

[@NetSloff]

@@crutchfield Thank you

[@NetSloff]

Unfortunately I've seen your message to late. Maybe you could tell me How can I reset that light?

[@willwarren3404]

awesome vid guys

[@tsvetomirstefanov7132]

how to connect cables? does anyone have a circuit for the radio cables for a Ford Escape 2008?

[@crutchfield]

It's best to use the proper wiring harness for your vehicle. You can be sure to get the proper installation accessories for your vehicle by using the "Find What Fits"application on the main Crutchfield website: bit.ly/2l32bTh For additional assistance and personalized recommendations, feel free to contact us directly by phone or through our online chat service: bit.ly/2jBGHPp Hope that helps --Crutchfield

[@snacking5908]

It would be great if you guys make a video for the 2001 - 2007 model. There are no good videos for receiver installations and the instructions that come with the package aren’t even worthy of being called vague

[@crutchfield]

I doubt we will be able to get our hands on one of those models again to make a video. We do have our MasterSheet instructions does show the removal and install process of a radio. Those come free with the purchase of the gear from us. If you purchased the gear elsewhere, you can order our MasterSheet for your Escape here: www.crutchfield.com/I-rYTVc000/p_264MASTER/item.html

[@snacking5908]

Crutchfield it was very vague

[@crutchfield]

I'm sorry about that,l Ahmed. If you purchased your gear from us, have your order number handy and give our tech support team a call. They'll be happy to walk you through the install process.

[@RushilDuvedi]

So helpful thanks

[@zero-io6sr]

Le hubieran puesto subtitulos.

[@felixthehandyman201]

You forgot to let the viewers know you only have to push the ac vent forward not up!

[@WeatherWarriordotnet]

MAJOR parts of the process MISSING. Didn’t address any proper panel removal, antenna or satellite radio connectors!!!!.

[@mr.2cents.846]

Doesn't look too hard.

[@granbubba1]

What's this guy looking at???

[@ogopogo1397]

my 2011 factory ford head unit is one of the worst sounding stereos in the world.

[@crutchfield]

We will be happy to check if that radio can be replaced. Which model Ford is it?

[@matthewabney3889]

This is a comment section if you don't want to answer people's questions on wiring diagrams then shut off the comments section quit trying to peddle your parts on everybody not everyone can afford to buy plug & play stereo equipment the more you help the more customers you'll get down the road take it from a veteran electrician we got enough salesman in the world.

[@thesnoman1]

I find Crutchfield to be very helpful. I recently made a purchase and when I had some issues their tech support went above and beyond to help. As you said yourself "this is a comment section" so do I have to point out this is not a tech support section? If you want help from them contact their tech support directly instead of crying like a baby.

[@newyork819]

Do the steering controls still work the radio?

[@jessiperry60]

does the steering wheel volume controls still work after a new stereo is installed in a 2011 escape??????

[@crutchfield]

The steering wheel volume controls can still work, but it does require an adapter to keep those working.

[@cramirez946]

Does the rear sub and amp still work? Or would i need a wire harness for it to still function?

[@crutchfield]

Hi Chris! You will need a harness to retain a stock sub and amplifier. There are times, depending on the vehicle, that your stock amplifier cannot be retained. It is all dependent on what types of harnesses are available for your vehicle. If you're interested in upgrading your stereo, feel free to reach out to us by chat or by phone. We will be happy to check fitment, as well as take a look at the installation products you will need to retain factory features. www.crutchfield.com/I-rYTVc164/contact