2009 Rogue A/C Clutch replacement

[@Wadagamebinmisin]

Great video man, my wife’s 2013 Nissan rogue started blowing hot air while she was driving, when I looked the ac clutch was not engaging, tested fuses, put power to ac clutch and still nothing! I bought a $40 eBay ac clutch nd installed it just like you showed, I used 3 original washers and 2 that came with the new ac clutch and the pulley was spinning pretty freely! Now My wife’s ac is nice and cold again! 💪🏼💯👊🏼🫡

[@lakesautomotivediagnostics6509]

Awesome

[@roberts1159]

Currently doing this same job on a 2011 Rogue. Pausing for now due to those three Philip head screws for the coil not removing ! Need to get a impact screwdriver and hopefully that will remove them. Getting the shim thickness was a pain for sure. This car has three shims originally plus two in the kit. Thanks for sharing this video.

[@lakesautomotivediagnostics6509]

I think I took that clutch off and put it back on four times. I edited half of it out, that was definitely the worst part of the job getting them shims right.

[@roberts1159]

@@lakesautomotivediagnostics6509 Thanks for your reply. I finally got the clutch assembly off and new assembly on this car. Used the three original shims first try and it was slightly dragging. Used one of the kit shims and that worked perfect. AC blowing nice and cold again. Your video was definitely helpful !

[@lakesautomotivediagnostics6509]

I’m glad you got it done and it’s working good and I am glad the video was helpful, I am pretty new to making these videos. Thanks for watching like in subscribe :-)

[@roberts1159]

@@lakesautomotivediagnostics6509 I did like and subscribe. Hope this helps your channel.

[@ThunderbirdRocket]

Fantastic tutorial ! Excellent teaching technique !! Helpful !!!

[@lakesautomotivediagnostics6509]

Thank you

[@mspeir]

I just did this job on my 2010 Murano. I also bought a $50 kit off of Amazon and had the exact same shim issues as you did. My kit came with four shims, one thick and three thin and the original part had three thin shims. I tried every combination of shims to get it work, and ended up using all four shims AND a washer like you did. It's working, but I think it's a little too far out. What makes this worse is that there isn't a spec available for the distance. What is too much? No idea!

[@lakesautomotivediagnostics6509]

I just shimmed it out until I didn’t hear it making noise

[@jwctech]

Was gonna say something about the flowers, but then I read the end..good vid bro!..

[@lakesautomotivediagnostics6509]

Lol,ty

[@picsbyjlm8557]

Awesome vid

[@lakesautomotivediagnostics6509]

Thank you

[@yulbertorres9710]

Thanks

[@lakesautomotivediagnostics6509]

You’re welcome thanks for watching like and subscribe. have a great day.

[@jeanpaulkapongodealmeidatr6263]

What's the Puller size???? Please! 3" 4" or 6"??????

[@lakesautomotivediagnostics6509]

Not sure what size you would call it, definitely not a six on the puller arm it says 75 mm

[@dickjohnson9582]

4"

[@tonystochmal2646]

Where you guys located?

[@lakesautomotivediagnostics6509]

Indianapolis Indiana

[@kalpeshkapadia4623]

Thank sir

[@lakesautomotivediagnostics6509]

You are welcome thanks for watching like and subscribe

[@raulcontes5533]

very usfull information!!!!!!!!!!!!FROM PUERTO RICO!!!!!!!!!!

[@lakesautomotivediagnostics6509]

Thank you 😃