Tips and bolt locations for intake removal 2.5l ford 2011
Пікірлер: 26
@chrisehresman81982 жыл бұрын
As a ford and chevy owner this video is making me want to sell the ford... thanks for the video!... now I know what my tomorrow looks like.😁
@CeeJay-pr5eg2 жыл бұрын
Perfectly instructed, you did awesome, saved me so much time thank you very much for your guidance.
@darrinfaulkner89112 жыл бұрын
Thank you for the short but to the point tutorial.I just ordered a intake manifold today and have to do the same to my car shortly.
@hallvw4 жыл бұрын
The pipe that's sticking out of the engine into the intake on the driver side is a 22mm to remove. The injector fuel rail is two 10mm bolts to remove. One bolt I forgot to show is a 13mm on the bottom of the intake, access it from underneath looking up at the intake
@edwinporrata26662 жыл бұрын
Best way I seen to remove it,thanks so much
@crankshaft007 Жыл бұрын
Thanks posting 4 cylinder, would have been nice to see intake out and next steps
@mikegalloway38613 жыл бұрын
You did a great job sowing how this all goes together. I appreciate the already lose bolts, I don't need to see how to work a ratchet, LOL!
@hallvw3 жыл бұрын
Thanks Mike
@jeddavies36355 ай бұрын
There's a hose on the bottom above the starter on the back of the intake manifold that has to be carefully disconnected or it will break during the final removal!
@jeddavies36355 ай бұрын
And the metal tube on the right side inside the manifold (pictured at the end of the video) has to come out using a 22mm or 7/8 wrench
@adventureswiththetwins27344 жыл бұрын
very helpful! i have a 08 ford escape 2.3 and i cannot get the water pump off i have removed 3 bolts holding it and have chipped peices of it and it has not budjed i was thinking taking the intake off and the thermostat housing to hit the water pump from behind do you know if waterpump can be hit with a pry bar from thermostat housing hole?
@stankelly64312 жыл бұрын
thank you for your video. can you tell me where the MAP sensor is located on this very same engine. can't seem to see it want to attempt working on my own escape. can't afford a mechanic now. thanks.
@argoyle902 Жыл бұрын
I believe it’s in the air intake if you undo clips to air filter it should be right inside
@124marsh2 жыл бұрын
Is there any other specialized tools you need besides the sockets. Thank You for making this video.
@hallvw2 жыл бұрын
No nothing specialized. You're welcome
@rafaelmartell7278 Жыл бұрын
Tendrás el vídeo donde se encuentra la válvula y la sustituyes?
@hallvw Жыл бұрын
The PCV valve is on the back of the intake. It's right there where you can get to it when you take the intake out.
@bobl.22132 жыл бұрын
I was gonna remove the Starter to try to get to mine since the PVC is between the Starter and intake manifold. If that doesnt work this will.
@justlg33598 ай бұрын
Did it work?
@oldwrench5797 ай бұрын
Why did you replace the PVC valve? What were the symptoms?
@hallvw7 ай бұрын
Been awhile on this one. If I remember correctly, rough idle, lean codes. Ran it back to the hose had a crack in it causing a large vacuum leak. So replaced the assembly while it was apart.
@AC-gu7rg2 жыл бұрын
Question, can you please tell me exactly where the pcv valve is located on that engine . Please and thank you
@hallvw2 жыл бұрын
It's bolted to the backside of the intake. 22mm to remove the pipe sticking into the intake
@AC-gu7rg2 жыл бұрын
@@hallvw I thank you very much for getting back to me , appreciate it !