2012 Mavic Crossmax SLR rear hub service

2012 Mavic Crossmax SLR rear hub service

[@dan7k]

Just perfect and simple manual! Thank you buddy, on the way to service my SLR with red hubs.. :)

[@Peanutbutterjelly00]

Danis Lee hey man My rear axle just broke in half and I can't find a replacement anywhere. Its out of stock everywhere and mavic don't even sell them anymore, This is unbelievable.

[@teamsandu]

This is such a helpful tutorial. Thank you so much !

[@ckupcu]

Very good video by the way!

[@dogger2186]

Add some grease to the tip of the spring to keep it from popping out

[@jrsandiego]

@Ziya, I believe Problem Solvers, Shimano and DT Swiss sell centerloc to 6 bolt pattern adapters.

[@ckupcu]

The special black screw on the non-drive side (@10:00min in the video) sometimes get loosen by its own on my Mavic CrossMax SX wheels. This is when I drive the bike on a very rocky downhill trails. The wheel may have a slack as high as 2-3mm when you push/pull the tire to left/right. I found this a bad design flaw and not amused about it 😞I fixed this problem by designing a 3D-printed 2.60mm ABS spacer ring between the end-cap and the special black screw. In case this special black-screw gets loosen again, the spacer will block - hopefully it does not become worse... If you guys suffer such a problem, you should measure the gap with a digital caliper and build a spacer like that.

[@erikknudsen4034]

Nice video... and the last 15 seconds cracked me up. So with these new freehub bodies... there's no neoprene bushing that wears out like the older Mavix FHB, which then cost $70 to replace?

[@jonienglish3231]

good video how the wheel holding up now in 2016 ? still have them ?

[@z1522]

I wouldn't advise using auto brake cleaner on bikes, as generally it can penetrate and mangle seals and other rubber rings. Finish Line or White Lightning sprays are o-ring friendly, and don't damage paint either.

[@wilbloodworth7345]

Nice video. Curious why you're running an Ardent on the rear.

[@he347]

First of all thank you for this awesome video. What is brand of centerlock to 6 bolt converter tool?

[@jrsandiego]

@ripptorr.. I can't comment on the use of Phil's or Mavic One.. But I have had good luck with Slick Honey... As for the locknut.. I have not used any loctite but definitely will keep that in mind if I have issues with it loosening up on me..

[@dair805]

Nice! Exactly what I was looking for.. Question; on 4:21, could put some Tri-flow oil on the bearings? Will it help to run smoother? Probably not or what do you think? 😅 thanks!!!

[@jrsandiego]

I don’t think it would be a problem... my one concern would be.. that it may attract dirt to it..

[@dair805]

jrsandiego got it.. Thanks your replay! Nice vid!!

[@jrsandiego]

@Wil... For this bike.. The fast rolling Ardents suits the trails and the way I ride..

[@kovacsbela9144]

where can i get bearings for it?

[@MrTwangthang]

@@kovacsbela9144 www.bikingbarn.co.uk/Components/bearings

[@jrsandiego]

I can't comment on the ST's.....but the SLR's have been pretty awesome....pricey but awesome..

[@ripptorr]

mavic recommends using some threadlock when reinstalling the freewheel locknut. I just use some loctite 243. Just to be on the safe side. Would be curious which oil suits better to use, the mavic one or Phil's. I have both in my shop and the mavic one is thinner. Any one tried them both to give a feedback?

[@fondoo]

Do you recommend the SLR or ST cross max?

[@Qpaification]

Why did you remove axel? (I don't have the tool)

[@jrsandiego]

Just to thorough with the maintenance.... the tool came with the wheelset

[@Qpaification]

Thanks for reply! I bought used bicycle without tool so I think I will skip removing axel since I cannot find this tool for purchase anywhere.

[@jrsandiego]

Check your local bike shop that is a Mavic dealer... they may have a spare one to sell you

[@kovacsbela9144]

where can i get bearings for it?

[@jrsandiego]

I would call Mavic for part#... then try Bocabearings.com

[@kovacsbela9144]

@@jrsandiego thanks I found some in a british website

[@Peanutbutterjelly00]

Hello everyone. My rear axle just broke 😭 and I can't find a replacement. Does anyone know where i can get the axle? Thanks

[@jrsandiego]

For something like that... I would contact Mavic...they May warranty it...

[@Peanutbutterjelly00]

jrsandiego thanks for the response but I already contacted mavic usa and they don't make that anymore and online everybody is sold out.

[@jrsandiego]

If you have a part#.... ask your local bike shop to check with their distributor to see if they have left over stock..

[@Peanutbutterjelly00]

jrsandiego thanks

[@stupido1977]

very nice

[@acstec2012]

ASMR video.. lol