2012 Subaru Impreza CVT Transmission Valve Body to Fix Codes P2764 and P0700

[@elpinchediablo6666]

Thank you brother, i had this issue on my 15 Subaru impreza (P0700 only) I replaced transmission valve body and problem solved.

[@varpholous]

Very good job. Thank you for sharing with us. One thing which is cheaper to do is replacing only the lock up solenoid in the valve body instead of replacing the whole unit. It will take care of the error message and car will be brand new. This relates for error P2764 for transmission type TR5800 like the one you have . All the best of luck.

[@JustinBalasco]

Where did you buy the solenoid? I can’t find it

[@varpholous]

@@JustinBalasco i bought it from ebay Best of luck

[@jimsumner7360]

You for be a good neighbor to have

[@surferporroloco]

Hey bro! I got the same codes for my Subaru forester 2014 just to know how do you think will be a fair labor price for this job?? Thanks for you vídeo bro so straight to the point!

[@harrissafi2831]

I changed the valve body but I can’t clear the code. P2763 circuit high clutch solenoid and P0974 circuit high shift A

[@valdesc36]

Buenas noches. No se necesita poner la computadora para quitar los códigos, cuando se levantan las 4 ruedas del carro y se hace el proceso que Usted nos muestra allí se apagan las luces de los códigos que da?

[@robertchiarizia9463]

I have code p1724 gear 4 incorrect ratio, which either the control relay, which it doesn’t appear to be, or starter interlock circuit short to ground. Can this be repaired inside the valve body / by changing the valve body?

[@elit3m3xsoldi3rs]

Tengo una outback 2011 cvt ,donde se ubica el cuerpo de válvulas por encima o por abajo de la transmisión?

[@lh98]

Was there any issue with 1st to 2nd gear shift or was it just the check engine light?

[@jimmallari9980]

I have the same error on my 2012 Impreza along with the ABS, if I replace the valve body all other codes will be fix? and by the way, I am not experiencing the symptoms on both codes could it be a sensor issues only?

[@ckzauto_videos5097]

Yeah once you replace it everything will disappear and sorry for the late reply

[@mayorga327]

So u didnt have to program new valve body ? Having same issues with my 2013 impreza

[@ckzauto_videos5097]

yes I did at the end ! so to do it I lifted the car all tires up then change the gear drive, reverse, park couple of time. if you watched the video to the end you would see how I lifted the car

[@valdesc36]

@@ckzauto_videos5097 codes are cleared by lifting all four wheels. I just changed a solenoid since it had the same problem and the same codes and I can't clear the codes, I haven't started the car yet. When I lift all four wheels I just start the car. Do I have to discount the battery before lifting the car or not? Thanks.

[@ckzauto_videos5097]

@@valdesc36 oh when you lift the car, you have change gear to drive for few seconds then reverse and neutral for few seconds again then you keep doing that cycle for few minutes. It the codes should disappear later ! Sorry for the late reply

[@carlossenquiz5627]

@@ckzauto_videos5097 dealership told me I need to replace valve body harness..i haven't been able to find one..they could not relearn/program

[@alexismartinpena2844]

Hola tengo este problema el mismo código en un subaru legacy 2013 es el mismo procedimiento?

[@mbasportstraining4238]

What trouble codes did you get from the valve body?? I am dealing with AP it P2764 and P0 700 and and C1432

[@ckzauto_videos5097]

I got codes P2764 and P0700 you might have some lights on like ABS etc.. but all that should disappear once you change the valve body

[@kvlempire4114]

Where did you purchase the parts ?? I went everywhere auto zone they don’t have it…

[@ckzauto_videos5097]

Hey ! The valve body itself I got it online but the other ones like small parts I went to the nearest Subaru shop to buy it