Pulled out this 2013 Ford Explorer so it could be rebuilt. Put it back in when the rebuild was completed!! Thanks for watching! I spent some time on this one hope it is helpful!
Пікірлер: 87
@buddylove8263 жыл бұрын
Dude this guide was super helpful. I really appreciate it! I'm the type of guy who likes to do his own things, but don't have the knowledge. Step by step, easy to follow. Took me a few days to complete, but got it done! What's next? lol
@doingstuffwithdylan43673 жыл бұрын
Thanks a lot! Really reminds me why I make videos! Glad it was helpful!
@leeblount60592 жыл бұрын
Hey brother I've thoroughly enjoyed watching The transformation of that transmission Thanks for the knowledge and the entertainment.
@doingstuffwithdylan43672 жыл бұрын
Thanks for the comment and watching!!
@IndiansAuto Жыл бұрын
Doing this on the ground on my back rn lol. Not at easy. Great job
@doingstuffwithdylan4367 Жыл бұрын
I never wish to do that. Better man than me. Good job to you! Thanks for the comment
@gonyoujeremy959611 ай бұрын
Thanks for this awesome guide! For those doing the 3.5 tt version, you'll also need to pull out most of the boost pipes. I had to remove the rear turbo oil drain and disconnect the water feed to get the PTO out. If I had to do it again, I would consider dropping the suspension, cradle, roll bar, and steering all as an assembly.
@doingstuffwithdylan436711 ай бұрын
Thanks for the tips!!
@juanbarragan6157 ай бұрын
My 2014 is starting kicking when the 3rd gear goes in and feel a delay then the thump. Check the transmission oil and looks clean . Hope I can have it fix and not fully rebuilt. Great work you do Sir.
@doingstuffwithdylan43677 ай бұрын
Good luck we see a few of these.
@gerardosalom67093 жыл бұрын
I found the video interesting, my friend, greeting from Venezuela My name is Gerardo Salom , very good
@doingstuffwithdylan43673 жыл бұрын
Thanks man! Greetings from USA!
@juanjimenez68803 жыл бұрын
Respect 👌
@doingstuffwithdylan43673 жыл бұрын
Thanks!!
@tavo68812 жыл бұрын
You are the man. Thanks for making this video. I’m about to tackle one of these tomorrow. How much time did you have in tear down and install.
@doingstuffwithdylan43672 жыл бұрын
Probably around 5 hours total. Thanks for watching. Hope it’s helpful!
@bobbygarcia8288 Жыл бұрын
Awesome! Quick question, should the trans cooler be replaced with new trans?
@doingstuffwithdylan4367 Жыл бұрын
Ford recommends it. We flush them. Never had an issue. Thanks for the question!!
@dannylay79653 жыл бұрын
Thanks, great video! 👍 I’ve got 352k miles on mine and the transmission is slipping. Do you think it be worth it to replace the engine as well while doing the transmission and transfer case, or would it be twice as much work?
@doingstuffwithdylan43673 жыл бұрын
The rest of the car is just as old. Removing the trans and transfer case do provide room to remove the engine. Is your engine bad?
@joeoconnor87Ай бұрын
Any thoughts on bolting the transfer case to the trans and then installing them together?
@doingstuffwithdylan4367Ай бұрын
I think the top bottom rear bell housing bolts would be hard to get too. Thanks for the comment.
@polylite3262 жыл бұрын
Can you a show oil pan r and r please? I was looking for how to “move the transaxle slightly back from the engine”
@doingstuffwithdylan43672 жыл бұрын
Sorry I primarily do transmissions. Thanks for comment!
@DaxSweetser Жыл бұрын
Do you by chance have a part number for the transmission fluid cooler line seals? The ones on top of the transmission. I believe that’s what they’re called. My transmission (explorer), Is leaking from that line with the 8 mm bolt holding it down, on top. Can’t find the replacement oring seal, if there is one at all. TYIA!!
@doingstuffwithdylan4367 Жыл бұрын
No I’m sorry good luck
@DarkExplorer961 Жыл бұрын
You sure do look like you know what you're doing there I wish we had some decent mechanics around here anyway great job man I know soon I'll have to have that done to my 2015 Explorer recently it started jumping and skipping through gear shifts I was advised to put some friction modifier in, it actually straightened out the problem but it still doesn't feel just right I just wonder do you have any idea how long that might get me through?
@doingstuffwithdylan4367 Жыл бұрын
Not really sure. I’m actually a little surprised it straightened out. Good luck and thanks for the comment!
@Movieman19657 ай бұрын
What friction modifier did you use?
@jonathanrandall82403 жыл бұрын
I have a question some I’m getting a used trans off eBay that has 48k miles on it with warranty and I’m going to be putting it in my 13 Ford Explorer. The number matches up. Will I still have have it towed to the dealer for programming ?
@doingstuffwithdylan43673 жыл бұрын
Probably not. Most fords don’t need programmed. We rebuild them though. Thanks for watching!
@Sean-ei9iw Жыл бұрын
I just dropped my first transmission on a 2011 Ford explorer note I've been a mechanic for 20 years. Watching your video really made me mad my steering rack I had to buy a one and a quarter inch wrench grind the head down for the box and to get my rack off makes me managers just came off with a quick zap of the gun on another bad side my torque converter will not come off so you have any information about the torque converter either staying on or coming off I would appreciate it
@doingstuffwithdylan4367 Жыл бұрын
The torque converter is stuck to the fly wheel? If this is the case try 2 pry bars and a helper. If you are talking converter clutch engagement let me know
@Sean-ei9iw Жыл бұрын
Thank you. I was scared to do that didn't want want the flex plate to break. My buddy did that once.
@bs081502bs3 жыл бұрын
Just curious on the total cost of the removal, rebuild and install. I know it'll be different from shop to shop, but I'm going to have to have my done and wanted maybe a ballpark figure. Thanks for the video BTW, I thought about doing mine myself, but I'm having second thoughts about doing this in my gravel driveway.
@doingstuffwithdylan43673 жыл бұрын
Right around $3000. Yeah I don’t think I would try it in a driveway let alone gravel. Thanks for watching!
@IndiansAuto Жыл бұрын
@@doingstuffwithdylan4367 doing it on concrete in my driveway way. It a lil challenging on you back.
@la-ia14043 жыл бұрын
You got any tricks to get the rusty bolts off on on the exhaust flex pipe? I tried pb blaster and the blow torch and am still afraid it will break off.
@doingstuffwithdylan43673 жыл бұрын
Heat. Oxygen and acetylene
@doingstuffwithdylan43673 жыл бұрын
And if they do break heat flange red cherry hot and drive out stud and put through nut and bolt!
@Bottomfeederonfire Жыл бұрын
Where are you located? If you’re within driving range I’ll bring my explorer to you for the tranny. The shops in my local area are atrocious. Looks like you do solid work.
@doingstuffwithdylan4367 Жыл бұрын
Ohio. Thanks for the comment I try.
@SR-gt3507 ай бұрын
Great video! Need more light. Looks like a black hole.
@doingstuffwithdylan43677 ай бұрын
I have since upgraded my lighting.
@icyhotmike3 жыл бұрын
I hope they put a new PTU in with the new transmission. Barely any fluid came out when you unbolted it. They should have 16oz fluid but the exhaust cooks it up. Definitely recommend anyone doing this procedure to invest in the PTU and modify so it can be drained/filled regularly. The torque converter is another weak point and should be replaced if you're this deep into it.
@doingstuffwithdylan43673 жыл бұрын
Very true we do a lot of ptu replacements on these! Always use a new converter. Thanks for the info comment and watching!
@bestwes91189 ай бұрын
Have you ever changed a Police Interceptor PTU with the external oil cooler? If so, how do you reinstall the coolant hoses that run back into the PTU? I cannot for the life of me figure out how to get them to sit back into the housing. Thanks.@@doingstuffwithdylan4367
@tylersanders3818 Жыл бұрын
My 2012 Ford explorer has a p0715 code after it was shuddering. It slammed really hard going into the next gear then the wrench light came on and when i tried to accelerate it barely wants to move and is in one gear. It also sounds bad after that happened.
@doingstuffwithdylan4367 Жыл бұрын
Sounds like you need a transmission shop. The shudder is the converter going bad. Once that happens it wipes out the rest. Sorry to have to give you the bad news. Thanks for the comment.
@Ambercooper0224 Жыл бұрын
How long did the entire job take? Removal and reinstall.
@doingstuffwithdylan4367 Жыл бұрын
I don’t remember exactly. Probably 6 to 8 hours.
@aceklub2k52 күн бұрын
Did you use an engine hoist up top?
@doingstuffwithdylan4367Күн бұрын
Nope supported from below.
@camuppodcast Жыл бұрын
Have you ever tried to make one only RWD
@doingstuffwithdylan4367 Жыл бұрын
It’s the same minus the t case and driveshaft.
@rmoran99993 жыл бұрын
Is it easier to pull a motor and then take the transmission off
@doingstuffwithdylan43673 жыл бұрын
I don’t think so. Good luck if you go that route
@mph58963 жыл бұрын
Thats how I do them. I don't have a 2 post lift though, just a midrise that gets the car up about 4ft.
@alrod85112 жыл бұрын
Help I swapped mine on my 2013 explorer but now mph needle won't move or go past first gear do I need to reprogram or reflash the transmission?????
@doingstuffwithdylan43672 жыл бұрын
Is every thing plugged in? Did you get from junk yard?
@doingstuffwithdylan43672 жыл бұрын
Most of the time these do not need reflashed or programmed. No Speedo is likely why it won’t shift. I’d check all the plugs first for bent pins.
@baldheadjamaican25513 жыл бұрын
How many miles did it have on it. Nice work that tranny small as hell.
@doingstuffwithdylan43673 жыл бұрын
Not sure man. Thanks! Looks small its kind of heavy though. Thanks for watching!
@baldheadjamaican25513 жыл бұрын
@@doingstuffwithdylan4367 ok cool thanks
@cristinowise47342 жыл бұрын
Curiosity could you tell us what the original customer stated as how we diagnose the transmission?
@doingstuffwithdylan43672 жыл бұрын
On this particular transmission it’s hard to say. I just remove and reinstall them but generally they slip and stop moving. Thanks for the comment and watching!
@alexgarza27592 жыл бұрын
What does something like that cost
@doingstuffwithdylan43672 жыл бұрын
Right around 3000 total. Usd. Thanks for asking and watching!!
@derekmaloney2477 Жыл бұрын
Would a 2016 Ecoboost one be much harder since you have to remove that rear manifold? I'm about to tackle one tomorrow and nervous about it being an Ecoboost 😬 any advice is much appreciated 👍
@doingstuffwithdylan4367 Жыл бұрын
I don’t think it will be much harder. I do plenty of transfer cases on those and the rear cat is not hard to remove. Especially with the subframe out of the way. Did not be nervous just nuts and bolts. Good luck let me know how it goes! Thanks for the comment!
@hershelr.sullivaniii71395 ай бұрын
You need lights.
@doingstuffwithdylan43675 ай бұрын
I’ve since upgraded my lighting.
@hershelr.sullivaniii71395 ай бұрын
Yay! Is this the quickest and easiest way to remove the trans/transaxle unit? @@doingstuffwithdylan4367
@wm59442 жыл бұрын
How many mille's?
@doingstuffwithdylan43672 жыл бұрын
Not quite sure. Thanks for commenting and watching!
@iphoneambulance91513 жыл бұрын
Better than Mitchell1 haha
@doingstuffwithdylan43673 жыл бұрын
Thanks for watching! I try. I have better lighting now!
@anthonyderas88692 жыл бұрын
how much does that job cost?
@doingstuffwithdylan43672 жыл бұрын
Right around $3000 usd. Thanks for asking and watching!
@anthonyderas88692 жыл бұрын
@@doingstuffwithdylan4367 And if the transmission is obtained in a junk car how much would it cost to change it?
@HeirByFaith2 жыл бұрын
Yea.. fuck torque specs.. 🤣
@doingstuffwithdylan43672 жыл бұрын
Not sure how I missed this comment? Love it! Thanks for watching and taking the time to comment. Some things I will use specs on. Few. Lol!!
@mikethomas73613 жыл бұрын
Lighting sucks!
@doingstuffwithdylan43673 жыл бұрын
Agreed I’m sorry. I’m trying to get better lighting! Thanks for the feed back!
@havocracing6019 Жыл бұрын
Did you support engine from top?
@doingstuffwithdylan4367 Жыл бұрын
I did my think so I would have included it. Thanks for the question!