2013 Nissan Rogue P0101 MAF sensor, Remove clean and Installed

[@DireDwarf]

Hey thank you for making this video. You just saved me and my wife. Our 2014 Nissan Rogue broke down due to an oil change place not reinstalling the air filter correctly. We broke down in the middle of nowhere in South Dakota outside the badlands. With this video I was able to get us back on the road. Thank you so much. Seriously.❤

[@RBTheMechanic]

Nice glad video helped u out

[@DireDwarf]

@@RBTheMechanic you have no idea. Life saver.

[@jimmycollins133]

Thank you so much - not always the fix, but certainly worth the effort!!!

[@RBTheMechanic]

Yeah I had few most worked out one didn’t work out even changing it it needed ecm upgrade

[@johnhunt9942]

Great info and I thank you. One question, can you spray to the connector that plug into the mass flow as well? You know, just to keep it clean? Thanks!

[@RBTheMechanic]

Yes u can buy u have to get the correct spray for connectors

[@johnhunt9942]

@@RBTheMechanic Great! What are the correct spray are call? Electronic spray or what? Thanks again. (Just now learning this.) ✌🏻

[@RBTheMechanic]

@@johnhunt9942 I have it in one of my videos kzbin.info/www/bejne/i33Gin-CbLSWqq8

[@jbryansoto]

Have you done a throttle body cleaning or any video on it to disassemble and assemble

[@RBTheMechanic]

Not on this car but other cars I have

[@jbryansoto]

@@RBTheMechanic shoot... okay that's fine I have some low idle and vibration at stops. I'll clean the mass airflow sensor and the throttle body see if it works. Wish me luck 😅

[@RBTheMechanic]

@@jbryansoto throttle should definitely help out

[@jbryansoto]

@@RBTheMechanic thanks man

[@RBTheMechanic]

@@jbryansoto once u clean it up if u get check engine or speed it too high or it act up I do have few tricks to fix that try it first if it’s good nothing to worry about other wise let me know

[@kingdon9690]

I'm hoping you can help me here, I have a 2013 nissan rogue 2.5l sv/sl. I had to change my step motor on the valve body it's the code it threw. I can drive but it sometimes take a bit to take off, but in reverse it has like no power. Then I hooked up my neighbors snap on scanner that's gets deeper into transmission codes, and it gave me a crankshaft position sensor code along with the step motor. I reset both to see if they will come back but they don't. But I wanna know what is causing the sluggish affect in reverse especially over a little hill at the end of my driveway. Should I replace the crankshaft sensor? Will that cause the sluggishness in reverse and drive?

[@RBTheMechanic]

I think this might be transmission related. I would check fluid but I could be wrong it seems like weak transmission

[@kingdon9690]

@@RBTheMechanic yeah I have fresh fluid, brand new filter and everything in it. But there is another filter I guess on the top side of the transmission. I got a different scan tool and now get a code saying that it has low pressure.

[@RBTheMechanic]

@@kingdon9690 not sure bro I’m not super smart at transmission but did u do the sensors u said earlier

[@12322gfshh]

P0171 I got this code on the same car on this video what do you think it is?

[@RBTheMechanic]

U have to clean the sensor first if it work out good if not replace it

[@12322gfshh]

I'll give it a try thanks

[@Osmondlloyd]

My car moves slow on acceleration after a full stop and then it surges forward. It also revs high. Could it be my maf sensor?

[@RBTheMechanic]

It might be related to transmission going bad

[@Chudsy2218]

Late comment, but did you ever get this figured out? I’m having the same issue in my 16 rogue only the slip indicator light comes on as well while driving

[@Osmondlloyd]

Found out transmission was shot. 5 year old car. Got rid of it last year

[@nv6399]

Thank you!

[@eusebiojrbueno4663]

how to clean the throttle body?

[@RBTheMechanic]

I don’t have video on that but u need tot ale the duct pipe off and then see if throttle opens with key on accessiries and push gas peddle to open the flap engine off and u can clean it how ever u will get idle rpm code with check engine and u will need to relearn idle

[@MrSuperScarface1]

I got code P0101 and P0101p. Can you help with code p0101p ?

[@RBTheMechanic]

Clean out ur maf sensor or replace it I would clean it first the rest the light and hope it don’t come back

[@xolit]

I'm having a problem with my 2008 Nissan Rogue , first it gave me code P0301 , we changed the coil, cleared the code and everything was fine for couple of hours , then again it gave another code same but it was P0302, it was the second coil. Any idea of why this would happen ?

[@RBTheMechanic]

Coils are failing change then all put in hood coils

[@BillSW]

did u solve?

[@RBTheMechanic]

@@BillSW yup been good

[@brianholder94]

Is there a re code step after reinstalling sensor

[@RBTheMechanic]

I didn’t catch what h said but once’s ur done just reset the light and keep givers crossed 🤞

[@tonyc7689]

does it need to be reset by the code.machine or will it reset itself ? looking for a reply as I did follow all you instructions this morning, ty vm I appreciate you very much !

[@AntonioGarcia-pb1wd]

@@RBTheMechanic ya hice eso que procede despues de averlo instalado ? Hay que borrar codigo?

[@RBTheMechanic]

@@AntonioGarcia-pb1wd sorry idk spanish

[@xolit]

@@AntonioGarcia-pb1wd Si tienes que borrar el codigo , ya sea con la maquina o simplemente quitale la bateria para que se resete.

[@kshaw2421]

I have code 0841 on a 2015 Nissan Rogue Help?

[@RBTheMechanic]

That code is related to transmission pressure it could be fluid or pressure sensor

[@kshaw2421]

@@RBTheMechanic Ok thanks so much....How much does repairs normally run?

[@RBTheMechanic]

@@kshaw2421 this can cost u up to $450 best to do it ur self

[@kshaw2421]

@@RBTheMechanic is it a hard task and where is the sensor located?

[@mazeg2109]

Just replace the sensor with a new one don't be a Micky Mouse mechanic

[@shkokurda2098]

3 minutes job. 7 minutes speaking. 😢

[@RBTheMechanic]

Ok!!! Need to explain! Yes talking is important and required and job is 1 minute not 3