2014 Toyota Sienna oil change.

[@nicolefonseca8088]

Thanks, you’re the man

[@PeterZafra]

Cheers

[@jamesanderson4014]

Looks like the torque is 25 Nm. Special tool makes it easy. Thanks for the video

[@PeterZafra]

Cheers

[@muhash50]

Thank you. You are very good in your job and detail oriented person. Appreciate it.

[@PeterZafra]

Cheers

[@somesingwong]

Amazing how you can produce such a high, short, and concise quality video with just your left hand. Kudos to you. Thanks for sharing such insight.

[@PeterZafra]

Cheers

[@Alexr2735]

Thanks

[@PeterZafra]

Cheers

[@alitokhy9080]

I really appreciate thank you so much

[@PeterZafra]

Cheers

[@bechtoea]

Spoken to many a Toyota mechanic. They don't mess around with the center piece at all. They also don't use the Toyota OEM wrench. They instead use this one: www.amazon.com/gp/product/B00XTAGHU0/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 And they just remove the filter, never removing the middle part. The other thing that is good to remember is to torque the oil filter to the suggested torque which is very low at only 18 ft lbs.

[@njsongwriter]

That's understandable because they are usually working by a flat rate and not by the hour. Thus they will take short cuts to make more money. That's fine but for teaching a novice how to do it the official method makes sense and is less messy IF done properly. It's your car do whatever you want. I'm retired and in no hurry and will follow the suggested procedure.

[@bechtoea]

@@njsongwriter The other reason most Toyota Mechanics don't pull the center section is it has a habit of breaking, especially if some monkey overtighened it. I neglected to say that part.

[@njsongwriter]

@@bechtoea I've never seen the drainbolt on the filter housing break. What breaks are the plastic oil filter caps and the oil filter wrenches.

[@privatesender9657]

This is the only video that I have found that actually shows and explains that u need to remove the small round silver piece FIRST. Even the video video made by Toyota just emphasizes u need this special tool. Not one time do they mention the proper way to do it and where the small ring/gasket goes. Great video!!!

[@PeterZafra]

Private Sender yes. And the silver piece is to release pressure although other people say no. The plastic piece that comes with the filter I used to release pressure. Glad it helped you.

[@njsongwriter]

Guess you didn't read the instructions that come with the OEM oil filter...

[@njsongwriter]

@@PeterZafra Show me one official source that says there is pressure in an oil filter when the engine is not running.

[@yuriy797]

You release residual oil from the filter not pressure

[@PeterZafra]

Cheers

[@michaelthai8760]

Thank you for your instruction...I have been doing it al wrong until I see your video, once again thank you man.

[@PeterZafra]

You are very welcome. Cheers

[@millertimeny11]

Awesome...thank u brother

[@PeterZafra]

Cheers

[@stevensevek6151]

Many folks doing this for the first time will find your oil filter cap wrench to be grossly inadequate especially if it was put on way too tight. Get a Motivx # 2320. The plastic drain for the oil filter is not to release pressure. It's just to drain the oil from the filter housing to make less of a mess. The only time there is pressure is when the engine (& oil pump) is running. It's not 25 pounds of torque. It's 25 N•m (Newton Meters) which equals only 18 ft.lbs. And the drain plug on the oil filter cap should only be 10 ft.lbs. The only pressure in the filter housing is the spring tension holding the element in place. There is no air pressure or even oil pressure when the engine is not running.

[@ricardomierz8467]

Yes, and he puts the ratchet extension into the plastic drain tool opening and uses new rubber washers for sealing up the filter holder and a lock nut for the oil drain.. 😵

[@phildern6203]

The plastic filter housing drain tool is not used to release pressure but rather to drain oil from the housing. It just saves you from making a huge mess when removing the housing.

[@PeterZafra]

Phil Dern cool. I guess it helped mine release pressure because when I removed the bottom cap, I stuck the plastic piece and once I did that, there was a sudden release of oil then removing the filter housing was a breeze at that point. Thanks for the input.

[@stevensevek6151]

@@PeterZafra Sudden release of oil caused by gravity...

[@littlec6954]

Great video now we need one for transmission oil change

[@PeterZafra]

Will do soon. Cheers

[@landshass2849]

I was at Walmart, and I opened three boxes of this OEM Toyota oil filter. Yes, the number printed on the filter 15613 is different than the one on the box! Just go with the one on the box. The number on the box is for the whole set (filter, o rings, and drain nozzle). The number on the filter is for Toyota use and it's not cataloged for public use.

[@Psycho.NYC.77]

Thanks I did it myself. No more worrying about getting ripped off.

[@PeterZafra]

Cheers to those savings.

[@majobismusic]

Thanks for the video. My last Sienna was a 2004 and was so much more straight forward filter wise. I’m going to take your recommendation on getting the filter removal tool.

[@PeterZafra]

Thank you for watching and subbing. Cheers

[@SsgtMcNasty1]

Putting oil on the O-ring is for when you put it back together so it doesn't stick. If the metal is dry, the O-ring can be damaged when you tighten it all down. You should put it on the ends of the filter element as well.

[@Taricarris55]

What is the name of the tool with which you remove the oil filter and where can I find it

[@fruitloops3718]

By loobing the o rings, you reduce the chance of pinching and damaging the o ring as you have lubricated it. They changed the style of oil filter in order to reduce the number of diy people that change their own oil. If you make it more complicated, more people will take it to the shop for an oil change.

[@PeterZafra]

Cheers.

[@muhash50]

Its Lube. May be lubricating. Or may be lube-ing.

[@himdadabdullah8145]

Good bro

[@PeterZafra]

Thank you.

[@steved.9839]

25 nm is a little over 18 ft lbs

[@MidwestSurvivalCompany]

How to do this with out the special tool?

[@PeterZafra]

I wouldn't do it without the tool. Depending if you have the aluminum housing or plastic, you can crack it.

[@condor5635]

Good video. Best not to have oil cap off unless you are actually filling. Just loosening and keeping it over the hole is adequate to equalize pressure and not create a vacuum. Hate to have anything go in the hole by accident. As mentioned pressure is not released at any point of this entire procedure - it drains the cartridge only for there is no pressure in the housing. There is a gasket as well for the drain bolt. Better make sure you have one on there. Lastly no way I would start with over 1.5 quarts low knowing that it takes 6.5 quarts and the filter housing being empty. Thanks for the video. Good looking Sienna

[@landshass2849]

Walmart sells Toyota OEM oil filters!!! Yes, I bought this exact same one last night for $6.97+ tax. It's not cheaper than my local dealer but since I was at Walmart to get my Mobile 1, it was a one-stop-shop. It does have the instructions on the box. By the way, it's made in Thailand.

[@PeterZafra]

Nice. I just get mine at the dealership. I'm pretty sure the ones at Wal-Mart is not a genuine Toyota part. Just make sure because the generic materials don't have the same material. But if it is, then you scored. :) cheers.

[@zachwulf6961]

Peter Zafra they are genuine Toyota oem filters

[@stevensevek6151]

I usually use Toyota OEM or a K&N filter and Walmart Supertech 0W-20 full synthetic oil. And I change it every 5,000 miles.

[@MurodjonAhmedov-zg3ug]

2014 Sienna Oil filter serial number. Assalamu alaykum

[@AlA-uu8qs]

Thanks Peter for the great tips on how to change the oil on the Sienna. Awesome tip on the tools that we should purchase before to change the canister. 👍👍

[@chrisduby4564]

The oil filter should be removed first, because it takes much less time to drain all of the oil out of the filter housing, than it does to drain all of the oil out from the oil pan! I always allow at least one to two hours to drain the oil from the drain plug! This way I get much more of the old oil out than I could, if I only let it drain for say, fifteen minutes!

[@PeterZafra]

Thank you. Cheers

[@MyLe-yt4ne]

great video and good explanation for whoever want to do oil change diy

[@Victorubee]

Be careful of over tightening the oil filter housing, the Recommended tightening is 25 + or - 5 N.m(Newton Meters) not foot pounds. One N.m(Newton Meter) is equal to approximately 0.74 foot pounds. 25 N.m is approx 18.4 foot pounds.

[@guadaluperodriguez-dy3rw]

you is right , there is a conversion sheet with instruction that comes with the oil filter ;it's 19+-4 lbft for the housing and 9.5+-2 for the bottom cap.

[@RayForrester]

came to say this

[@cour1988]

Nice catch

[@MyRebel44]

Read the directions on the box .

[@nickot7690]

25nm newton meter is 18.5 ft/lbs Welcome =)

[@PeterZafra]

Thanks. Cheers

[@tedl8534]

Think it'd be possible to just use oil filter pliers to remove/reinstall?

[@PeterZafra]

Hmmm. I would avoid it to prevent damage.

[@PeterZafra]

If you can get a good grip on the side without compromising the casing, then sure but we careful

[@stevensevek6151]

I wouldn't. You could try it but if you can't get it off you'll need the proper tool.

[@njsongwriter]

How would you know it torqued correctly with pliers?

[@jaychan5211]

Where can I get that tool or what's it call ? Thx

[@PeterZafra]

Got mine on ebay. Just put the year of your car and you can see different ones.

[@jmardinly]

Never use a screwdriver to remove O rings! Use a wooden tool or you risk scratching the seal.

[@PeterZafra]

John Mardinly I agree. That's why we gotta do it carefully and right at the open groove provided. Cheers

[@stevensevek6151]

Instructions that come with some filters will say to simply use your hands/fingers. Including the instructions with the OEM filter and the instructions in a Haynes Repair manual.

[@njsongwriter]

@@PeterZafra It's simple to do without tools IF you know what you're doing.

[@Taricarris55]

What is the name of the tool with which you remove the oil filter and where can I find it

[@PeterZafra]

I just looked it up on ebay. You will see it there. Just punch in sienna and year oil filter cover tool

[@Taricarris55]

Peter Zafra thank you very much it was very helpful i found it on amazon

[@jca203]

Where did you get that tool to remove the filter? I have one that covers the whole cover but I like the one you used better.

[@PeterZafra]

Hi. Got it from eBay.

[@guadaluperodriguez-dy3rw]

i believe he said he bought it online but did not mentioned what place

[@ambertucker8326]

I can't find one. What's it called. I like the looks of it better than the regular oil filter wrenches.

[@UndreamedFool17]

Tea-yota

[@Thebigbwayz]

It take Walmart 2hr to change my oil.

[@PeterZafra]

They're usually very busy there with not enough employees.

[@Thebigbwayz]

Peter Zafra I agree ☝🏼

[@cour1988]

6.4 quarts just FYI

[@PeterZafra]

Thank you. I always just return what i removed with fresh oil. Works great all the time. Cheers

[@darenmiller4605]

Toy-Yoda

[@stevegrant4225]

Always use a Toyota oil plug drain gasket. The reason you had to use so much effort to remove the plug was the gasket was missing, so it was metal to metal. Also the drain gasket seals better without over tightening.

[@PeterZafra]

There was no gasket missing. The previous person that changed the oil over tightened the cap. Cheers

[@perritochihuahua2094]

Making more complicaded so dealer can make money 😕

[@PeterZafra]

Seriously.

[@stevensevek6151]

Not true. That was not Toyota's intent at all. Why Cartridge Filters kzbin.info/www/bejne/p3maaqh6h5eMfK8

[@johnydoe7065]

Why did they make it so complicated just use a regular disposable filter

[@PeterZafra]

I agree.

[@njsongwriter]

Here's a good question... WHY are you asking us? Ask Toyota.

[@njsongwriter]

The filter (element) is disposable.

[@eddo1717]

The plastic tube in that comes with the oil filter is to put after that you take off the round cap, you tide up with your hand it is to drain the oil in the filter canisterafter drains remove it.

[@JustIce-zv8pk]

Do you have link for oil wrench? Thanks

[@PeterZafra]

It's been a while. I got it on eBay Just put Sienna oil filter tool.

[@njsongwriter]

Best one for Toyota made engines 2.0 liters and larger us the Motivx MX2320 seen at ... www.amazon.com/Motivx-Tools-Toyota-Filter-Engines/dp/B00XTAGHU0/ref=sr_1_2?dchild=1&keywords=Motivx+2320&qid=1601082845&sr=8-2

[@TheSteelGamer]

25 N - is Newton not torque

[@klakytklak]

very long video and never said exactly how oil is supposed to go in it. thanks for wasting 15 minutes for anybody just trying to see how much oil goes in it . should delete video so people can go right to a better one.

[@PeterZafra]

Try measuring how much you drained out. Then return the same amount. Then measure the dip stick. Cheers.

[@klakytklak]

its 6.4 qts.

[@njsongwriter]

You keep calling the oil filter element a canister. It in not a canister. Some people call the housing a canister and at least that makes sense cause a canister contains something. Like a kitchen canister set has a number of canisters for storing flour, sugar, etc. The paper element is NOT a canister. It could be called a cartridge because this system is called an oil filter cartridge style system. The cartridge is what goes inside the housing or inside the canister. And all oil filters come with the plastic service pipe for draining the filter not just the OEM filter as you claim. Some push in and some screw in depending on the brand. And your drainplug or drainbolt is not called a lock nut. Jeeze is there any end to this...? It's one thing to make a mistake but twice you called it a lock nut. Do you even know what a lock nut is?

[@PeterZafra]

Oh my gosh. I am sorry.... haha. Next time i will remember. Thank God i don't do this for a living. I'm just glad my little mechanical skills have helped thousands and got around my mistakes. I'm also glad i saved thousands myself. Thank you for your input. Cheers