2015-2023 Mustang Steeda Rear Vertical Link Billet Aluminum Pair Installation

Bill shows you how to install a Pair of Steeda Billet Aluminum Rear Vertical Links on your 2015-2023 Mustang.
Purchase Product Here:
www.cjponyparts.com/steeda-re...
Wheel hop has been a common worry among Mustang straight-line racers. One place in the IRS that will often affect wheel hop is the soft vertical links. Thanks to Steeda, there is a great option to upgrade those vertical links and put more power to the ground with your 2015, 2016, 2017, 2018, 2019, 2020, 2021 2022, or 2023 Mustang. Today, we're going to install them on this 2015 Mustang GT.
Check out more Mustang Rear Control Arm parts from CJ's here:
www.cjponyparts.com/mustang-re...
Check out more Steeda parts from CJ's here:
www.cjponyparts.com/steeda/c/8...
Subscribe to CJ Pony Parts on KZbin here:
kzbin.info_c...

[@chevyhs]

Just installed these. A real pita. To get the bottom bolt in, you need to take a pry bar and rotate the arm to get the rear of the lower bolt to go all the way through. Rear end feels more stiff when the suspension moves up and down

[@D1G1TALSYNAPS3]

Thanks for including torque specs

[@wannak00kie]

Mine have been squeaking because the grease they give is trash but I refuse to go through the stress of trying to install these again. this and the irs bushings were just horrendous

[@5thmonth791]

You need to jack up the arm alone in order for that bottom bolt to fit if not you’ll be there for more than you have too

[@lissandrofernandez8750]

Nice number on Pump Gas,all stock👌👌💪💪

[@biggrigg8558]

Mine did’nt come with the grease, what kind is it so i can buy some

[@christlike_5.043]

hey bill, which pole jack are you using in this video?

[@2001busa1]

Hey thanks for all the awesome videos. I have a non performance pack gt and have pretty bad wheel hop. Does it seem like non pp mustangs have more of a wheelhop issue due to a softer spring causing more movement in the suspension? I'll be ordering parts as soon as the weather starts getting nice. Wheelhop is driving me crazy. Thanks again

[@peterpeters4111]

Sam Scornaienchi I have the same model as yours as and went with Steeda bushings and subframe brace but noticed the ride quality isn't as good as before and much stiffer ride but tolerable! I actually like the fact that the base GT has a soft ride but now it's really firmed up and more disappointed because Steeda says it's not suppose to affect our ride quality. It's major winter here in Canada but from what I can see the take is much better and will improve even more when I get my Michelin Pilot Sport AS 3's back on the car in the spring time.

[@JohanSalvattore]

@@peterpeters4111 super late reply but I’m glad for your feedback. I have an 18 gt non pp and I actually wouldn’t want to give up the comfort of this suspension. I’m on eibach pro kit lowering springs but I didn’t think I would like any more stiffness. Maybe just a set of beefier swaybars will do.

[@Aloneinthedarkso]

Wish I saw this video a few months ago! I still haven’t gotten these on mine…

[@davidlopez991]

I'm in the same situation. I supported the knuckle from underneath and I still cant get the lower bolt all the way through. If there is special technique to this it should be spelled out in the video. Not sure I will be able to fix this.

[@RealChickenMan]

The way I did it was bottom first, jacked that b*** all the way up and stuck a big screw driver through the knuckle and the toe link and lowered it slowly... Boom lol first one took hours, second 15 min lol

[@seanpair1382]

Cj pony part, how well do these work without the subframe connectors with a full bolt on 2016. Should I go ahead and get both or will this be sufficient?

[@Mr318live]

Definitely both

[@harley1001]

hour 3 of the 1 hour install 6 foot long pry bar and shreds of thread and aluminum all over bushing

[@dandeac1907]

It's that replacement require any alignment? Or don't have anything to do with alignment? I'm really consider to upgrade this stuff in the spring.

[@Zerogivengarage]

No these will not require an alignment.

[@dandeac1907]

Bill Tumas thank you for reply.

[@Travide]

Going to do these the bushings and subframe all at the same time.

[@cjponyparts]

That is the best way to go

[@mattg2596]

@@cjponyparts no doing a full 9k in mods at same time is way to go! fuck jacking the shit up every week.

[@eclypse3d]

Ok KNUCKLEHEADS lol j/k. come on guys the install is buttery easy save your selves some headaches on the lower bolt. just put your jack under the lower control arm and raise it slightly till the top bolt slides in, then insert the bottom bolt. if it stcks just lower the control arm or raise it a hair, it will go in real easy. This install should take you about 40-45 mins to do. No need to make more work for yourself, just use your jack :) hope this helps....

[@scottcrawford4148]

That didn't work for me.

[@garrettpittman7374]

End results vary alot w this install...I wound up returning mine bc I couldnt get them to line up...now I have ordered a different set and am going to try again