07376369067 www.williamsmobileclutch.co.uk Support the channel: www.paypal.com/donate?hosted_...
Пікірлер: 120
@Nypartcannon2 жыл бұрын
I don’t think people appreciate how hard this is to do on the floor and outside especially in less than half a day and without any errors Master tradesman !
@WMCS2 жыл бұрын
Thanks Naill…
@craigc89542 жыл бұрын
Considering what you’re up against, your camera work and editing is superb ! Makes such an enjoyable watch.
@gavdcookuk5122 жыл бұрын
They seem to have fixed every ancillary system to the gearbox here, right angle impact wrench and uj sockets earned their money on that job, top marks sir !
@kenlarman42522 жыл бұрын
Probably one of the best in-depth step by step how to videos I’ve watch on KZbin 👍 the camera positioning & editing alone must of taken just as long as it did for the clutch change itself, hat of to you pal give me the confidence to change mine myself if the engine lasts that long 👌 was a deserving watch to let the adverts run to the end without skipping through them.
@Phil-19692 жыл бұрын
Kevin don't go hurting yourself. That gearbox was a two man lift , you are a strong young man, but you don't want to be surfing with back problems later in life . Take care, you are still the master
@WMCS2 жыл бұрын
Hey Phil… at first glance it thought “ ay ay ay … “ this one ain’t gonna be easy. And it definitely lived up to it. What a payload.
@andymorgan5190 Жыл бұрын
Thanks mate. Got mine to do soon. Gonna save me garage fees
@massorioslo7339 Жыл бұрын
Wow you are good. You totally dominated this gear box.
@massorioslo7339 Жыл бұрын
Can I ask .. did you lower or liftet the engine while installing gear box ? I tried today on my 6 gear ,gear box , but i failed. It was hard to put it in the line and push it forward. I'll try again tmrw :)
@shukurmiah62222 жыл бұрын
Wow just seen your video for the first time and lost for words how you done it on the floor and how fast you done it as well. The whole vidoe show you how to do it and how easy is it step by step. My transit clutch is going in garage tomorrow and i will be there helping the guy to do it but next time il be doing it on my own with the help of you and your vidoes! Thanks mate
@donb77402 жыл бұрын
Wow I am relieved trans seated to the engine on the 2016 Ford diesel and your sigh of relief was self evident that the hard lifting part was over. Congrats
@christiank5340 Жыл бұрын
Amazing work. My arms are exhausted just by watching you move that transmission. Lots of respect! Good in depth video!
@WMCS Жыл бұрын
Thanks for the feedback
@nealcotter62852 жыл бұрын
Great work ethic,you have amazing skills Kevin, I hope you charge well for your expertise.all the best.
@MrSupernova1112 жыл бұрын
Wow! Impressive on so many levels!!
@alessandrer36162 жыл бұрын
The best mechanic in UK ! Thanks for sharing ! Respect king Kevin !
@billrimmer55962 жыл бұрын
Excellent job Mr. Clutch Man!!
@md-detailing2 жыл бұрын
Love watching these videos! Keep up the great videos and i really love your work! :D
@ssimons32082 ай бұрын
woooowww you are a great mecanik, and strong also to lift the gearbox thanks for the vid.
@TheFaridos132 жыл бұрын
Terminator of the clutch respect and good job 😀
@MrTransit0121 Жыл бұрын
Top guy I followed this video today amd all done in 2/ hours keep them coming plz 💯😎
@ko697722 жыл бұрын
Amazing! You can actually teach the cowboys at dealerships how it’s properly done. Keep up the good work mate 👍
@charley22123 Жыл бұрын
Excellent work ninja mechanic , good job and good to watch bud .
@OmarHernandez-jo7zb2 жыл бұрын
Congratulations. You do a excellent job. Believe me is perfect.
@didier90072 жыл бұрын
le roi de l'embrayage chapeau bas
@adammartin47775 ай бұрын
It is very impressive buddy doing this job without a ramp, hats off to you
@paulert232 жыл бұрын
that universal clutch alignment tool is super neat
@user-rz1oc6zr7h2 жыл бұрын
Приветствую вас Кевин и Альберт! Удачи вам, процветаний канала! 💯💪👋👍
@mikeberry3042 жыл бұрын
Another great job there Kevin, I ducked down when you split the bottom ball joints 👍👍👍👍🤣🤣
@WMCS2 жыл бұрын
Haha… a bit too close was it ..
@mikeberry3042 жыл бұрын
@@WMCS a bit scary , could see my reflection in the hammer ball pein head 🤣🤣🤣🤣👍👍👍
@tamiyafrog32202 жыл бұрын
Cup of tea im ready to watch.
@alloubiissam32192 жыл бұрын
I do it for 2.4 last week.with simple flyweel. It will be better to change oil gasket. Good job.
@steve57722 жыл бұрын
Now there's a job I wouldn't do on the floor no matter how much someone wanted to pay me. Seriously well done!
@WMCS2 жыл бұрын
That was a heavy weight one that box.
@jardelmendes24442 жыл бұрын
ÓTIMO TRABALHO CONTINUE ASSIM SEUS VIDEO SÃO DE OTIMA QUALIDADE PARABÉNS
@nigelsandywell84032 жыл бұрын
just Inspirational, good Job Sir.
@WMCS2 жыл бұрын
Thank you Nigel.
@markg6jvy1352 жыл бұрын
You love a big heavy awkward box 😉😂 Good stuff 👍👏👏
@WMCS2 жыл бұрын
That was real diamond that box was 😅
@VENUEATHENS2 жыл бұрын
i dunno how much you quote them for this job but I really hope it was worth it, seems very intensive, taking apart too much with very annoying angles to work.. You have a lot of patience!
@stemartin66712 жыл бұрын
I f£cking hate my job these days but I still enjoy watching you Kevin pal 😂
@WMCS2 жыл бұрын
Funny 😆…
@stemartin66712 жыл бұрын
@@WMCS 😂👍
@deniscudahy45492 жыл бұрын
Only 96k and needs a clutch ,bloody hell they don’t make them like they used to 🤣😂🤣😂👍👍👍great work as always 👍👍👍
@loverman20052 жыл бұрын
Good job as always and bit of a bugger about the rest of your footage but these things happen I guess , the stripping down of this van was pretty intensive , but you still sorted it and that box is a monster, what other cars did you do this week , keep going with the excellent job mate
@WMCS2 жыл бұрын
Mate that gearbox was half my size … Really gutted .. had some great footage in some amazing locations. Never mind that was God’s plan for me. But stay tuned for tomorrow’s video. Complete van tour
@mc40672 жыл бұрын
Hi Kevin great job... been driving 30 years+ never realised its not good to keep the clutch in for long periods after all this time, until recently lol. I'm one of those that keep the clutch down in heavy trafic rather than into neutral and handbrake even if its go slow for 15 mins and hardly moving... a couple of occasions ive smelt burning and now realise its the clutch caused by my own idiocy. So my Q is, have I been lucky and got away with it once get moving & all cools down .. or have I/ or could I have done damage to the clutch & if so do I need to change it, in which case a 2 piece clutch kit or a 3 ?.... I dont get any crunching of gears and my Transit custom drives flawlessly. This has only happened a couple of times when I'm in severe trafic jams and nothing moves for 10-20 mins bumper to bumper..once moving and its cooled all is well!
@franciscog.v.26212 жыл бұрын
poco trabajo esta semana? excelente trabajo como siempre.
@duybui5152 жыл бұрын
You are a legend mate!
@kiedelve112 жыл бұрын
As a tech at Ford van centre my hat goes of to you doing this on the floor, Just a suggestion, if you place a scissor jack between the engine and subframe it moves and holds the engine at a nice place for the gearbox not to catch the subframe.
@WMCS2 жыл бұрын
Thanks for that tip Kieran.
@meyerlansky45282 жыл бұрын
Incroyable mecanicien !! HIGT LEVEL .
@andy_v44432 жыл бұрын
the relief @41:10 and you just dust off ya hands and role over, get up and carry on... i would of laid there knackered for at least 10 mins, lol, excellent work kevin lad,{ or are you a machine ) BIG THUMBS UP FELLA
@WMCS2 жыл бұрын
Andy it was a bit heavy that box. Nearly the whole size of my upper body .. reminded me of my last girlfriend. I like them big 😁😁
@garyreynolds98742 жыл бұрын
Wat do you bench bro 🤣🤣👍 good job pal not afraid of hard work 💪👏👍
@nickclegg9434 Жыл бұрын
Really informative video with great angles. Quick question around this, with a model that has air-con would you remove the pipes to remove the box? Seems like it is very tight for space between the outside of the gearbox and air con pipes
@WMCS Жыл бұрын
You don’t have to. Once engine is lowered it will clear.
@nickclegg9434 Жыл бұрын
@@WMCS brilliant I’ll get to it thanks Kevin
@nilzr12 жыл бұрын
I can say from my own experience, that's a pretty heavy gearbox to lift on your own. How do you bleed the clutch pedal on your own though?
@yavuzdemircan34582 жыл бұрын
Helal olsun usta (Halal master) 🇹🇷
@eoghanhennessy4432 жыл бұрын
Have you came across the newer vivaro . 1.6 d . Flywheel can go on any way . Bolts lines up every way . You have be careful and mark the tdd mark when taking off
@WMCS2 жыл бұрын
Not yet. But I’ve heard that is the case. Otherwise it doesn’t run properly after. Thanksgiving the update tho ., much appreciated
@robertmobileman83042 жыл бұрын
nice work kevin , have you done a ford kuga yet ? plastic sumps , i might have one to do sometime, supporting the engine might be a pain , any feedback would be great cheers
@WMCS2 жыл бұрын
Hi Robert I’ve done the 4x4 version of it. It’s a nice repair. I’ll try and see if I get one to film.
@Bassam543212 күн бұрын
Super nice man. Great that you didn't cut a lot from the video ❤
@LAMECCANICA-channel2 жыл бұрын
Heavy job but for you Kevin all is easy 😉🙂😉🙂 top 👍👍👍
@zzest1114 Жыл бұрын
How you done this on the floor in that time single handedly and zero swearing I take my hat of to you sir
@fabifabi78562 жыл бұрын
Por dios con que facilidad levantas una caja y colocas la directa jaja algun dia me saldra 😅,saludos desde bs as,!!
@rigofutty51722 жыл бұрын
Good job!
@johnmorton54982 жыл бұрын
Don't know if you have or not but a 4lb thor copper mallet works wonders on drive shafts, you can get a full swing without damaging the threads.
@WMCS2 жыл бұрын
Thank you.
@stemartin66712 жыл бұрын
I just drift them out most have a recess in the centre of the shaft stub for that reason. Although I have mashed a few ends being rough in my earlier days, nowt an angle grinder or deemed won’t fix though 😄 And I’ve dealt with some seized up shite in my day lol 😂
@johnmorton54982 жыл бұрын
@@stemartin6671 the recess in the middle of the shaft is for when they're been made and supported at either end. A big 4lb copper mallet knocks them loose without a drift, if you miss the shaft and hit the hub then there isn't any damage.
@stemartin66712 жыл бұрын
@@johnmorton5498 fair point John, but it is perfect for that purpose however! I’m not knocking your methods btw buddy I’m just adding my two pence into it 😃👍
@stemartin66712 жыл бұрын
@@johnmorton5498 and if you miss the drift your hand usually takes the beating instead of the hub haha 😂
@15mechanix2 жыл бұрын
Good job 👍🏻
@gegegege78232 жыл бұрын
bonjour toujours Nikel👍👏👏
@ianwilkinson55493 ай бұрын
Mate they are a heavy box , you have the strength of 3 men.
@qobra832 жыл бұрын
good job!!!
@vanesc692 жыл бұрын
love it
@pawep79939 ай бұрын
Mega!
@maxthecaddy84512 жыл бұрын
Hi kevin that did not look fun to do, the size of that box, you defiantly earned you're beer token's for this job👍
@paullynch19386 ай бұрын
Top mechanic you are dude
@Ksebki2 жыл бұрын
Was there a movie with the replacement of clutches in the Fiat 500?
@WMCS2 жыл бұрын
Yes. Check on the channel.
@castrolgtx50642 жыл бұрын
That solid clonk when it slides home @ 39:35
@d.onecars4 ай бұрын
You f*kn beast, changed on my one to it was a hell to put the gearbox up again aloneee….
@gregbarr2242 жыл бұрын
I have one of this that need this done how much does it cost all in and do you travel ten out of ten for a driveway job dude
@WMCS2 жыл бұрын
That’s correct .. send over your details via www.williamsmobileclutch.co.uk
@maverick5072 жыл бұрын
hey kevin how are you you abandoned the videos of your work week? thank you for your work buddy 🥃🍻
@WMCS2 жыл бұрын
I’m gutted this week’s footage got corrupted on the SD card. So will be doing a Van tour video instead.
@maverick5072 жыл бұрын
@@WMCS Ah ok I understand, unfortunately it happens for me lol Good weekend to you my friend
@MarkDaviesThailand2 жыл бұрын
Hi Kevin, Looking forward to the van tour. Is there any place best to buy interlocking mats?
@user-yf5dd8lr8g11 ай бұрын
Hello there! bless your work! I am writing from Kazakhstan. Please let me know if there is a mistake in the translation! I have such a car from 2013. What could be the reason why the button does not go all the way back? Please tell me the known reasons?
@WMCS11 ай бұрын
Possible flywheel fault. Which is affecting the function of the slave cylinder and causing pedal not to full return.
@godlikeproductions78982 жыл бұрын
41:08 LOOL
@WMCS2 жыл бұрын
That was literally a weight off my shoulder 😄
@JVC_Official2 жыл бұрын
Ninja warrior :D
@scotspie501douglas72 жыл бұрын
big old gearbox well done
@user-jj1tv8el1g2 жыл бұрын
👍
@cepedacarlos22 жыл бұрын
What brand of tools you use
@WMCS2 жыл бұрын
Watch for Today’s upload on tool inventory
@markmawson12 жыл бұрын
About 10yrs ago I got asked to have a look at a lads Citroen Dispatch ex-police van (still had cage in back) he had started to have problems getting any gears and I said to him have you recently had the clutch replaced and he said no but not long before he bought it from the police auction their maintenance department had replaced it verified by the logbook service history it had, anyway I went round and had a look at it and low and behold I kid you not out of all the bellhousing bolts it should of had in it there were only the 2 bolts across the top holding the box in and they were halfway out because everytime he depressed the clutch pedal the box was moving away from the engine it was shocking they must have shot the van back together and forgot to tighten them bolts up.
@WMCS2 жыл бұрын
Shocking .. a Mr clutch centre asked me to do a clutch for them as the customer went back on a trailer. Same thing. Only 3 bolts holding the bell housing and all done up by hands. Now I wouldn’t blame the mechanic. But the level of how some garages operate is to keep taking mechanic off the job do something else and come back then get taken off again and they want the job done before end of the day …
@garethjones80472 жыл бұрын
Around 10 years ago I spent a good few years as a contractor for greenflag, Britannia rescue etc. I got called out to a citroen picasso 2.0 8 valve hdi. Lady owner told me that it had been to a Gearbox specialist here in north wales for a reconditioned gearbox and it was noisy so she complained about the job and they reluctantly asked her to return it for rectification, but she said they were swearing at her when she took it. They had the vehicle another week and now the gearbox noise had gone, but within around 30 miles it started making horrible noises, that's why she called her breakdown club. I popped my head underneath to find about a 10mm gap between the engine and bell housing, most of the bolts were missing and it was hanging on by a few. She took photographs for evidence and she asked if our garage could sort it because she had just lost faith in them, which we duly did. Tightening a bolt is the most basic of things, and if you cant do that properly then you should not be working on vehicles.
@markmawson12 жыл бұрын
I had same sort of thing with a Pug dealer they were the only dealer willing to do the timing belt on a Peugeot 407 couple 3.0l 24v V6 because they were the only dealer to have the timing tools to do the job, so I booked it in and they said it would take 6hrs for parts and Labour anyway dropped it off on the morning never got phone call that day so rang them next day see how it was going only to be told "we can't keep the tech on just your car" so I said to him well don't think I am paying you for the time he is doing some other jobs when he is supposed to be doing my job I said you quoted me £300 + vat so £300 + vat is all your getting and no more anyway went to pick it up and there were bolts loose that were in plain sight so I dreaded to think what was loose under the timing covers
@garethjones80472 жыл бұрын
@@markmawson1 sadly all this happens in the motor trade. I've got out of it. Too many monkeys spoil it for the good ones. It's the kind of trade young lads are offered, I know, I've been a young lad myself, but my father used to own a garage, so I was brought up on good standards from the age of around 12, I then left school and went into HGV mechanics. I'm glad I have the k knowledge I have, but as for doing it for a living anymore, the wage does not match the skill required.
@markmawson12 жыл бұрын
@@garethjones8047 totally agree, this is all I have ever know to do since I was a kid
@ricardo73602 жыл бұрын
very tough work
@oscar-jx3fj2 жыл бұрын
🤯🤯🥵🥵
@Vision20247 Жыл бұрын
Maan, I worry for you when you do the vehicles with these big-ass gearboxes
@WMCS Жыл бұрын
Worry is a silent killer … 🍻
@phigio13192 жыл бұрын
good job but too dangerous with jack stands👎
@WMCS2 жыл бұрын
Of course it is… ⚠️ it’s a bit like when a baby is trying to walk.. too much risk of falling over and getting hurt. Don’t get me started on learning how to ride a bike … the risk of injuries are so real … no one should ever attempt these things … you are a very wise man stay safe …
@phigio13192 жыл бұрын
@@WMCS je ne comprends pas je suis francais.je trouve juste que c'est dangereux 😄