How to Build a Ford 5.4L 3V Engine - Part 7: Timing Set and Camshafts

Рет қаралды 53,754

Күн бұрын

Пікірлер: 85

@2carpros Жыл бұрын

So I was mistaken when I said the Cam Tower bolts are TTY. They are reusable just torque to 89 inch pounds in sequence. But I do recommend the ARP ones because they are so good! Thanks for watching!

@joseaguilar3978 10 ай бұрын

Where I can find the engine block cam caps?

@jaholl97 6 ай бұрын

@@joseaguilar3978those are lined bored when engine is new. You cannot just buy new ones. They would to be machined.

@wh0_am_152 3 ай бұрын

You scared me! I was panicking thinking about how I could quickly get a set!

@DY-wp5tx Жыл бұрын

Another great episode! Can’t wait to see this dropped back in your truck and running. Keep ‘‘em coming!

@2carpros Жыл бұрын

Thank you for watching! Coming soon!

@mikeybhoutex Жыл бұрын

Ryan, your remark about the cam cap bolts being TTY and therefore junk was something I had not heard. Having recently done the timing on my 4.6L 3V, which has the same heads as this one, and having done so with replacement TTY phaser bolt and an ARP crank pulley bolt (because stock is also TTY), but having kept and reused the cam cap bolts, I was a slight bit afeared I'd messed up with this new information. So I went a-huntin', and I read the 'LH Camshaft Replacement' section in the Ford repair manual for the Mustang. And nowhere does it say to discard the bolts, as it does for the TTY phaser bolt. Others in other sites have said simliar: cap bolts are reusable. I'm fairly certain the 5.4 3V would be the same if I had a hold of that book? That's not to say that on a brand new build like this I wouldn't recommend ARP for all the things, so I whole heartedly approve for sure, but I just thought I'd run that by ya and see what you had for thoughts. Thanks for what you're doing, very much enjoying the series on this rebuild!

@2carpros Жыл бұрын

I have read that they are TTY on some sites and on others it's just 89 inch pounds so not TTY. I just looked up the Ford service resource and it just says 89 inch pounds so that is the resource I would trust. I believe you are right and the stock bolts are most likely fine to use again. I will leave a pinned comment to correct myself. Thanks for watching!

@natebug8614 Жыл бұрын

Best engine rebuild video ive seen to date. Keep up the good work. Awesome instructions. One question tho. Roughly how much would a job like this cost. (Parts and machine shop etc...) i think in part 4 you mentioned listing the prices. But i think i missed it that part.

@outsidethelines2162 Жыл бұрын

Such a great series! Keep them coming!

@goneballistic 10 ай бұрын

Great job on this video really well explained well shot and very very clear thank you

@2carpros 10 ай бұрын

Thanks so much for watching!

@jeremyhedge2151 Жыл бұрын

1st off, love your video series on the motor builds. Would love to see you guys do a 5.7 hemi build. Keep the videos coming

@2carpros Жыл бұрын

Thanks so much! I would love to do one too!

@jeremyhedge2151 Жыл бұрын

@@2carpros I have a 2019 charger pursuit awd with the 5.7. It doesn't have the dreaded tick yet. Would love to see a take on a rebuild where maybe it would take care of the lifter problem and some performance options

@DustyWallpaper-gb4ii 9 ай бұрын

I've seen in there that you rotated the engine counter. Clockwise, aren't you supposed to rotate it clockwise always just an observation. , but very good information

@2carpros 9 ай бұрын

Only if you are worried about the crank bolt coming out, which I wasn't. I just needed it to turn back a tiny amount anyhow. But if you are concerned about that feel free to rotate it all the way around clockwise. Thanks for watching!

@benjaminsilva8786 3 ай бұрын

Just an observation, the tool you used as a crankshaft rotator it’s not just a rotator, it’s actually the tool to put the crankshaft to his perfect timing. Great video tho, I’m rebuilding my engine as well and this is pure gold. Thanks a lot!!

@2carpros 3 ай бұрын

It would be if the hole on the tool lined up with anything. I think mine was made slightly wrong. But oh well, it worked! Awesome! Thanks for watching!

@leodeboca 4 ай бұрын

Excellent information, thanks man!

@PaulHenreid 8 ай бұрын

Where did you get that final timing diagram around minute 20:10? Perfect camera positioning and image quality. Did you reinstall the roller followers after installing the timing chains?

@JimmyMargenauJr 6 ай бұрын

Hello, Jimmy here. After doing the timing on a 2012 Ford Expedition 5.4 3 v, how do you place the roller followers back in? Haven't seen that part yet.

@ektorochoa1378 9 ай бұрын

Is there an specific reason you didn't installed the cam followers before the camshaft, did you installed them after?

@jixxer48 Жыл бұрын

When timing aren’t you supposed to turn crank clock wise instead of of turning it back to the left like you did and what position are the piston locations because you don’t want valve meating piston

@jr.3407 3 ай бұрын

no rocker arms.

@alejandroacosta5560 3 ай бұрын

Hello In your camshaft and timing.I must have missed when and how to install rocker arms. I am very interested in this process. Please help thank you.

@2carpros 3 ай бұрын

It's in the next video part 8 Thanks for watching!

@StayingBack71 2 ай бұрын

@@2carproscan't you install the roller followers first Before you put in the cam and caps?

@jrcll7856 3 ай бұрын

A Melling high volume oil pump is the best upgrade for that engine , 150.00 and you don`t have to remove the oil pan to change it, gives the engine 20 % or more oil flow

@calvincrewjr2158 5 ай бұрын

When your doing the right side how you get all the slack out of the chain on top before you put the tensioner on

@jettjensen4902 6 ай бұрын

Ok I’m confused because you say have the line up at 12 o’clock but fordtechmakeuloco says have it at 6 o’clock so can you explain why you two have a different answer? And also just because it’s at 6 or 12 shouldn’t it be at tdc on cylinder 1 and how do you know it’s at tdc on cylinder one just because the key way is positioned right? Because the crankshaft doesn’t rotate at the same rate as the camshaft so you can have multiple revolutions to 6 or 12 before a specific cylinder is at tdc

@2carpros 6 ай бұрын

I haven't watched his video so I can't comment. All I know is I followed what Ford says to do and my truck runs without issue so I did it right. Thanks for watching!

@jettjensen4902 6 ай бұрын

@@2carpros I watched it incorrectly he was just saying put it at 12 o’clock to remove the first 6 roller followers then put it at 6 o’clock to remove the rest of them. And on reinstall do the same I love your build series and it’s great to watch! Also what is you opinion on aftermarket timing kits such as melling?

@derrekallen2089 5 ай бұрын

Il@@jettjensen4902I just watched his videos and he says it needs to be at 11 but I'm going w 12 myself

@russbrockway1726 11 ай бұрын

the cam with the longer snout goes on the side that requires a shorter one?

@jixxer48 Жыл бұрын

Just wanted to get it right because I’m doing my 4.6 L three valve. I’m doing the timing I’m doing the heads so I want to get it right

@DonaldRosane-rd2lt 9 ай бұрын

Show the whole process to finish, running in the truck,very informative

@2carpros 9 ай бұрын

I do. Thanks for watching!

@robertosola7576 2 ай бұрын

So we don’t use any Blue Loctite on any of the bolts?

@2carpros 2 ай бұрын

No they are TTY. The Loctite might mess up the torque value. Thanks for watching!

@leodeboca 2 ай бұрын

I did exactly as you told us, but when I rotated the engine the marks on the timing chain a full rotation was not on the timing chain marks on the phasers, and 11 o'clock and six o'clock, I used the tool on the crankshaft for the timing so, I don't know if this is Ok. Please help.

@2carpros 2 ай бұрын

It's not going to be, the teeth add up un evenly so it takes many rotations to line back up. As long as you had it lined up like I did when you put it together it will be timed correctly. I did the same thing and worried about it till I thought about it for while. Thanks for watching!

@leodeboca 2 ай бұрын

@@2carpros Thank you very much, I was so worried, but you have cleared my doubts, once again thank you for your support.

@leodeboca 4 ай бұрын

Isn't that the engine should be turning clockwise only, or it doesn't matter? Thanks.

@2carpros 4 ай бұрын

It doesn't really matter. Especially since we are turning it so slow. Thanks for watching!

@leodeboca 3 ай бұрын

@@2carpros Thank you!

@AntonioGonzalez-pk8uf 10 ай бұрын

Hi a have question I did all the timing change and before I put the timing cover i turn my crank shaft to see my marks still line up but they r not I guess my question is I shouldn’t turn the crank it all after doing the timing change

@fercampos838 7 ай бұрын

Keyway goes at 12 or 11 o’clock?

@joecostu1571 6 ай бұрын

Get timing tool auto parts loan them

@PaulHenreid 3 ай бұрын

both depending on which phase in the timing process; there is actually a third keyway location at 6 o'clock in between if following by the book (factory manual)

@germanquiroz5780 5 ай бұрын

Is it the same process for 4.6?

@nic6049 8 ай бұрын

Ryan, is this procedure the same with the Ford 4.6 3V year 2006?

@2carpros 8 ай бұрын

Yeah it is basically the same engine but a bit smaller. There is some parts that are specific to the 4.6 so I wouldn't use every link blindly, just verify that they fit the 4.6 before you order. But the process is the same as I understand it, probably different torque specs though so I'd look those up too. Thanks for watching!

@justinspivey4151 5 ай бұрын

Hey Ryan, does #1 piston need to be TDC

@LupeTrevino-gk1lb 4 ай бұрын

You're the best man is 3'Vs series the same as a 5.4a, as

@LupeTrevino-gk1lb 4 ай бұрын

Triton 5.4 liter

@judahisrael9456 6 ай бұрын

@carpros can you do a tear down and rebuild for a coyote motor?? Please 🙏🏾 😊

@2carpros 6 ай бұрын

If I had the money I would! Thanks for watching!

@judahisrael9456 6 ай бұрын

@@2carpros thanks for responding I just want to tell you thank you, I watched your 302/347 stroker engine break down and rebuild and I didn’t realize building a short block isn’t that bad ..your video really boosted my confidence in doing the assembly myself for my 92 foxbody..also I have a 2008 4.6 mustang and was wondering is the assembly process the same as in the 5.4 video you did? Thanks again

@pedronazario223 7 ай бұрын

Even a 5-year-old child can install those timing chains because they have very clear markings and no one is going to make a mistake, but what is worth worrying about is if you don't mount the tensioner guides where they go, you will have to check the engine litgh. I won't explain. something that not everyone knows, and that is that the tensioner guides are not the same, one is thicker than the other, one is right and the other is left and they are not marked

@2carpros 7 ай бұрын

Right which is why I pointed out which one goes where. Thanks for watching!

@OscarPerez-ns2ob 8 ай бұрын

I could've wrong but left side phaser is not the passanger side?

@2carpros 8 ай бұрын

It is from the perspective of the driver's seat, so from behind the engine the driver's side would be the left bank. I know confusing. Thanks for watching!

@Grey0324 9 ай бұрын

I just did mine on my f250 and now I got the p0345 p0349 and from what I know I'm off by 1 tooth so how do I go back an reset the timing on bank 2 1 tooth again. It runs amazing but the check engine light keeps coming on after I changed the cam sensor an the pigtail. What do I do?

@StayingBack71 4 ай бұрын

It isn't that you put the chains on wrong, But you can't follow what he's doing here because The cam is free rolling. I'm sure you did your timing with the engine in the truck, And you didn't secure the cams When you took the phasers off. This video is very good but he should have explained the difference. Now if you did secure the cams, It could be off by less than a link to set off the codes. There is very little leeway on these stupid overhead cams that can move when you're doing these installations. I hate to say it but I think you're gonna have to get back in that front cover

@JASPACB750RR 10 ай бұрын

Why did you put the entire timing set together without the roller followers in? You’re gonna have to take all that back apart to put them under the cams. That’s why you have so much free play and the cams just spin about all freely.

@2carpros 10 ай бұрын

Nope. You have to put the cams in first then the roller followers. There is a special tool that pushes down on the valve so you can get the roller follower in. Thanks for watching!

@DustyWallpaper-gb4ii 9 ай бұрын

I am wondering the same thing ??

@cedricjohnson459 9 ай бұрын

So the timing can't be properly done with followers already installed under the cam?

@jonchicas-hw9op 4 ай бұрын

Where are the Lifter and rollers??? Hello Uninstall the cam but not everything else?? Why

@2carpros 4 ай бұрын

The lifters and rollers go in after the cam. Look at the next video in the series. It's not possible to install the rollers with out the cam to hold it in place. There is a special tool which I go over in the next video. Thanks for watching!

@JamesJackson-hw6kg 5 ай бұрын

That good

@rmkilc 9 ай бұрын

I mean, you could have your crankshaft 360° out of phase.

@2carpros 9 ай бұрын

360 out of phase? Then it would be correct. Do you mean 180 out of phase? And that isn't possible with the timing marks where I left them. The truck started up and works great so it is correct. Thanks for watching!

@rmkilc 9 ай бұрын

@@2carpros lol yeah. 360° out of phase is only possible when the timing system is already assembled.

@rickyhart9574 7 ай бұрын

One you are time and you never did say nothing about top completion stroke.

@2carpros 7 ай бұрын

As long as all the marks line up it is timed. It would be at TDC on compression. Thanks for watching!

@brunohoutwipper4225 11 ай бұрын

Why use the old shitty plastic tensioners that cause alot of problems. Should of used the cast iron ones

@2carpros 11 ай бұрын

Those are for the 2v not the 3v and can also cause problems check this video from Brian kzbin.info/www/bejne/o4e7qWumi76WZ8U

@randyjennings9853 7 ай бұрын

I am concerned confused if you put the crank straight up. I have a tool that holds crank in place while you do the top end timing it is at 11:00 O'clock.