Definitely add water cooling. I’ve have been working on mine for a while now and I added water cooling which works great and I added foam in the front end to keep it from nose diving in the front but haven’t tried it yet. Water cooling jacket for the engine and the Esc was easy to install which I drilled a hole in the jet right after the prop and installed a copper tube with a slight angle cut in the tube so it pushes the water through the tube into the boat. I ordered some fittings but you can 3d print something for the tubing to connect to in the back of the hull and one for the exit which I like having it pointing up so pushes the water in the air so you can tell how well it’s working.
@rcprinter2 жыл бұрын
Thanks, water cooling is definitely next on the list for this boat but figuring out the best way to do that on a jetboat is tough and I've seen a lot of pics of people putting the intake in a lot of different locations so thanks for giving me the feedback on what works best for you. I'm not 100% sure I'm properly picturing how your copper tube is installed so if you have a pic or something of it that would be helpful.
@dragonconley442 жыл бұрын
@@rcprinter I just drilled a small hole down into the first peace of 3d printed jet drive and stuffed a copper tube with a 45 degree angle. Pushed it down until the 45 is just sticking down a little bit so the water flow hits it. If you don’t have copper tube I would use a peace hollow antenna works great. Plus if you use a antenna there’s a bunch of different sizes you can try plus have plenty left over for another project. Anyway water cooled is the way to go even if you rap the motor with copper tubing is better than nothing. Also you can use the antenna to connect peace’s of tubing together or since it’s tapered you can stuff it through the back hull and super glue it in place to connect the intake and exit water cooling lines to. I hope that helps you out. Good luck and I hope to see a new video soon.
@Agloriousburrito Жыл бұрын
I was looking for this comment. Was just about to write a whole essay on how important water cooling is on a jet boat since it does not get any other types of cooling.
@brunssenboy2 жыл бұрын
Just ordered my first 3d printer mainly build rc. Just found your channel yesterday and I can’t wait to start printing!
@rcprinter2 жыл бұрын
Have fun, its a blast!
@brunssenboy2 жыл бұрын
@@rcprinter oh I will!
@BasBoyRC2 жыл бұрын
Interesting with the motor, heat is an issue. It you look at most brushless set-up in boats they are water cooled.
@rcprinter2 жыл бұрын
Yea water cooling is a must for the future
@Poulpc2 жыл бұрын
wow looks like it is fun to use
@rcprinter2 жыл бұрын
Sure is!
@Qwarzz2 жыл бұрын
Works way better than mine. I have water cooling for ESC and motor but it would still kill itself if I drive with more than half throttle for too long. Need to find more sufficient motor at some point.
@treerecords15512 жыл бұрын
what kind of esc and motor you using?
@1sqeeze12 жыл бұрын
it probably is not the motor, i had similar problems with my boat until i noticed that i messed up while filing the driveshaft so it could move in rear bushing. you shuld check all drive components if they are running freely and if your coupler is perfectly center since that might intoduce a high imbalance at greater rpm
@vazza69 Жыл бұрын
Inrunner with watercooling around
@tristanhodkinosn542210 ай бұрын
Where did you find the shaft for the prop and what dimensions is the shaft.
@yashnivalkar11315 ай бұрын
I am using throttle curve to limit the thrust for heating issue .... it does not go full throttle but it saves the motor
@yashnivalkar11315 ай бұрын
Not on same boat n specs but just for your idea ... will try building this model soon
@rcprinter4 ай бұрын
Thanks for the tip. I've been building the MJET Sprint and Supersprint lately which are quite an upgrade over this one. Should have a SuperSprint build video out soon and kits available at www.rcprinter.com.
@Thunder-xo1cx7 ай бұрын
Dude that's great we gotta meet sometime I am in Vernon BC
@carloshnunez2 жыл бұрын
Nice it runs very good now, a water cooling will be better 🔵🔵🔵👍👍👍😀😀😀🔵🔵🔵
@rcprinter2 жыл бұрын
Definitely
@jxfk31968 ай бұрын
Should i use a low kv or a high kv motor?
@AJWyman1 Жыл бұрын
Check out the M-jet 35 3D printed jet pump he dose a boat as well
@rcprinter Жыл бұрын
omg that thing is nuts.... going on the build list!
@googliola Жыл бұрын
@RCPrinter Thanks for testing and sharing. I am about to build the boat for this summer and I was wondering, what KV 3550 or 3560 motor you would recommend for 2S and 3S. I will try to fit water-cooling too.
@rcprinter Жыл бұрын
Hey water cooling is pretty important, I need to add that soon. I'd probably try 3000-ish next but I don't really know for sure. I think the 3650 I tested here was ~4300 which I think was too high.
@MrDINODINO74 Жыл бұрын
For the boats, you have to use water cooling on a speed controller and motor because the investment is capsulete, and brushless motors do not have ventilation
@MrDINODINO74 Жыл бұрын
... and to avoid cavity, you have to install one the half from the grid and another intake perpendicular. kzbin.info/www/bejne/gobNmIGGaMaSpLc
@rcprinter Жыл бұрын
yeah I'm definitely learned that this summer. now to figure out the best way of installing water cooling in this one for next summer!
@jeelansoni2866 Жыл бұрын
What is Max speed 1400kv
@yashnivalkar11315 ай бұрын
Which servo used ? Can you list electronics in description?
@rcprinter5 ай бұрын
This is the servo: rcprinter.com/products/20kg-digital-servo-ds3218-with-metal-gears-and-metal-servo-arm I've tried many different electronics. I'd go with a 540 motor and water jacket like I installed here: kzbin.info/www/bejne/r5ekoXyPj9-nbsk&ab_channel=RCPrinter No matter what you do you'll require water cooling.
@yashnivalkar11315 ай бұрын
Modified motor mount little will try 1000KV drone motor with 70-80% throttle curve to avoid over heating
@jackdaniels2657 Жыл бұрын
He needs water cooling and a bigger motor nd better jet pump impeller
@chrissantos3797 Жыл бұрын
Hi are you able to provide STL files for both the steering link TPU boot and the TPU seal for the main hatch. Many thanks.
looks like if it turns too hard the hole is exposed to the air,,,i would like to show u my build in fact.. its on thingy its the blue one with the white top I'm working out water cooling and water pump..its another version of the boat i think is made a lot better check it out...the guy is in the bashtech comments..i'll post all the new stuff i did to it soon like trim tabs ect.
@rcprinter2 жыл бұрын
Build looks great, love the rear wing. The water cooling installation looks really cool. You should do a video on it when you're done and show us everything you did.
@treerecords15512 жыл бұрын
@@rcprinter i was gonna try but...im having alot of issues...one being the same water invasion your having lol..i thought the pump would help but...idk maybe its my receiver...the amp draw is too much and everything reboots basically..