4 TON PORTA POWER FRAME MACHINE USING IT FOR FIRST TIME

[@xephael3485]

Awesome job, very professionally done. You can barely see the damage after you pushed out the dent!

[@nikkitrackwell8215]

thank you so much my car was rear-ended driver side twilight it old bit mechanical sound with low miles❤❤❤❤❤😊

[@cbrrebates]

It's so satisfying to watch you doing the work ☺️

[@celticcountry2119]

Thanks for your video . showing how to use the parts . the only thing that came with it was the parts manual not much help showing how to use it .thanks to your video I can pretty much figure the rest out.

[@weedguy204]

Thanks for idea

[@ilovecubes8598]

Watched you other videos, great topics and they are helpful! Thank you. But got a question: Did you (or a body shop) pull out the damage BEFORE showing us where you started using this 4ton tool? IF you had this tool earlier, do you think you could you have pulled out all the damage with the 4 ton tool?

[@D.Frasure]

Pretty cool guys!

[@jamesrushforth1026]

Bro i been watching loads of your videos is there a way i could contact you i have problem closing my boot and i think this could help me but not aure could i send you a video amd ask a little advice id be so greateful

[@jeffroberts3814]

I feel like after watching this video I have the skills to open my own body shop. I didn't realize it only takes 10 minutes to make it look like new!

[@Zero_motivation517]

This guys accent is crazy I could watch these videos all day

[@ivanhernandez1652]

The terminator?

[@realestateinfonet9041]

Great video! Thanks!

[@Love500]

Thank you. About to buy one and had no idea how to use it.

[@julispiri]

Ех Българче, Българче ❤

[@Engineerboy100]

Good job guys, just what I needed to see. Thanks, I think I'll go out and get me one now :) lol

[@loktom4068]

Thank you very much for your very informative tutorial.

[@natefidalgo7625]

seems time consuming doing it manually curious if those fittings can be used on a hydraulic pump or air compressor to speed it up and have less manual pumping. Nice explanation starting to get how these 10 ton and 4 ton kits work but most times it just better for a whole piece replace or its going to take you along time.

[@patriotmarf]

Studying the car damage from experience i would say that needs to get pulled on frame machine tied down properly. The frame rail would need to be replaced. If it was just qtr and rear body panel fine you could just hammer out spare tire well maybe some small kinks in frame rail, but hat metal is kinked good and it looked like he already pulled some of the panel out before video was made.

[@splash5974]

This is a joke! And they definetly arent fixing this themselves! Unless you have a frame machine, and knowledge of how to pull, they arent getting anywhere with this one...you can see the kinks around the area where the frame rail is. Hopefully they bought this cheap enough to sell the drivetrain and maybe front sheetmetal to try and offset the cost of this thing... People without proper knowledge, shouldnt be buying stuff at auctions!! Plus there is such a small margin of profit on these vehicles. I had a friend with a body shop that bought a few per year, but he only worked on them when they were slow. Cause he admitted that there really wasnt much profit on them.

[@xephael3485]

The back end needs to be cut off an a new uni-body assembly welded in place.

[@wdnick]

Can anyone tell me if the cylinders used in these kits have a spring return? Do they retract on their own or do they need gravity/assistance of some sort?

[@M70ACARRY]

They retract on their own.

[@memorymukabetamemorymukabe9589]

where can I buy that in south africa how much can that be and also price for the ten ton

[@wenzenuf221]

Addendorf. R2200.

[@MrGibratan]

thanks for the video very helpful

[@Lecon60]

Just used the wedge to push a large dent out of my door.

[@ethanrbutler]

First and foremost you should never hold, lift, carry or move any part of that kit by the pump handle or hoses. Hold the heaviest parts in your hands, not the lightest

[@WorldMechanics]

Thank you for the tips. Really appreciate it. It is still new to me

[@WATtheWhat]

Ethan Butl

[@sitifazleniibrahim7051]

Cara pasang tinted kereta

[@esteemedenergy]

That’s how MAACO fixes cars.

[@viscioushattermaid4410]

These guys should sell uzi’s instead

[@nagarage1973]

Top🚘👍

[@AlvinShen]

There is no way you can use that to fix that damage. You need to cut that whole section and weld in a new panel

[@TwoCarGaragez]

Alvin Shen I hope that’s what they did. But you should always pull it out before you cut it. Cause it brings everything around it to its normal position.

[@Usefullinformationphilippines]

You have to pull the metal back into place to realign the car before replacing panels or your doors and trunk will no ever line up then you replace the outside skin of the panel

[@AP-bo1if]

@@TwoCarGaragez just curious why do you have to cut it out? for example if they bought it for themselves and don't plan to sell it. is it because it won't pass safety or some other reason? also does the dealer sell those kind of metal pieces or you have to find a parts car? thanks

[@thepicazos6675]

CR7 suuuu!!!!

[@mikeoneal4882]

Is 4 ton sufficient vs 10 ton?

[@63GTDriver]

Mike ONeal I think so , for this type of repair. The 8 or 10 ton is a much larger unit, length wise and diameter of shafts.

[@daddyhermanson9737]

no way to fix that damage with 4 ton porta power

[@johnnyfiveable]

12 ton probably not enough.

[@Usefullinformationphilippines]

You have to pull the panel not push it. But it is his car and not mine

[@stephenr1999]

Why every one so critical? I have seen auto body guys do magic with panels i thought would have to replaced. Guess it pays all labor no parts to buy. just paint and filler.

[@blackisback74]

It came out as you smashed the inner part out by 3"

[@peternycpeterw7484]

I feel sorry for that car and the person that bought the car . How can you do that to the car

[@wenzenuf221]

Waste of money. Ok for diy. Seals pop after using a few times. Then it's junk. Buy the 20T one. No rubber seals.

[@TheRaiderCritique]

how is pittsburg brand from arbor freight?

[@TheRaiderCritique]

@Aaron Anderson I found out about 2 days ago it works really good I've bent out the whole firewall on my driver side front and I was able to line up the bolt holes. And with the help of a winch and sledge hammer, it worked out perfect! so anybody wants to know, use Pittsburgh brand from Harbor Freight. It works wonders. I got mine for $139

[@Csidney]

@@TheRaiderCritique Finally, someone that actually knows what he's talking about.👍

[@eddietavaresjr.4773]

10 ton should be good for a dump truck

[@oshawnkim3595]

This video is horrible nothing is in frame how do you expect anybody to see and understand what you're saying or explaining. It is very difficult to keep up if we can't see what you're doing. Thank you still for the video because it is an effort, but you got to do better. At the least look at it before you post it.

[@csabi72]

is it really worth messing with so much damage, ?

[@dannyyo7948]

yes! specially when your profit is really good on the resale.

[@xephael3485]

Yes. Especially when you hide it and sell it to people who don't know how to inspect or see if a vehicle has had body work done...

[@lucada8538]

@@xephael3485 over 40% of cars on the road have been hit, and if you buy from a used car dealership 95% of cars there where like the one in the video, thats why collision shops are a thing.

[@xephael3485]

@@lucada8538 your statistics are likely bullshit, and calling this collision repair is laughable

[@mrgrey361]

What the hell country is that accent from? And why do you say "guys" after everything?

[@jeffbarker730]

what you all just watched, is what we call "Butchers!" do not attempt to repair your vehicle like this !! you could not only jeopardize your life but someone else's !!

[@JohnnyBravo02]

Seriously . It was at the junkyard for a reason.

[@theframeman8021]

Butcher

[@aarondalton2223]

Goons

[@1972dazbo]

What a fucking botch job......chassis,back panel,floor,inner & outer quarter damage.....4 ton chinese porta power to repair wtf ? CAR NEEDS JIG ALIGNMENT & NEW PANELS.......FFS !!!