I was suppose to buy this. Thank you for your review. Really help me avoid a possible disaster.
@Electronic_For_You Жыл бұрын
Yes it is a disaster, There are more batter converters you can buy 😊
@harharmahadev567211 ай бұрын
Any other conductor similar to this configuration ??
@Electronic_For_You8 ай бұрын
There is a 150W Boost converter buy that one
@anascottwelding17615 ай бұрын
@holeangelvillareal3277 me too, it was in my cart. Not really even half as good as it should be.
@pault931411 ай бұрын
Thanks for video. If you replace nce8290 with the 75N75 MOSFET would that fix/improve it? Also why do you get shocked between heatsinks? can that be fixed easily?
@Electronic_For_You11 ай бұрын
I think i fixed it in video by adding a small load on the output you can see i used a diode and resistor combination, it shouldn't shock anymore! And nce8290 is 80V 90A MOSFET 75n75 is 75V 70A MOSFET
@tech.5137 Жыл бұрын
0:41 + output terminal and heat sink on one side are connected. The heat sink on the opposite side is connected to the ground side. When the maximum voltage is generated, high voltage is applied to both heat sinks. Risk of electric shock and fire. 0:41 +出力端子と片側の放熱板が接続されている。 反対側の放熱板はアース側に接続されている。 最高電圧が発生してる時は両方の放熱板に高電圧が掛かっている。 感電と火災の危険がある。
@Electronic_For_You Жыл бұрын
Yeas I got shocked from Heatsink 😅 thanks for mentioning
@casper92567 ай бұрын
What ga wire are you using to feed the device? It looks like you're using super tiny 28ga steel wire. Im no expert but what if you used a larger gauge copper wire? Would it still cause these problems? I have one of these I gor for .99cents so I can't really complain unless it doesn't work at all but I am curious
@Electronic_For_You7 ай бұрын
I used thinner wires , because they work as a fuse , and I think it's a good converter, if you don't use it for sensitive devices!
@anascottwelding17615 ай бұрын
Yes very good point, I was stressing watching him move it all about watching the 12v 10A clips rubbing. I was waiting fit the sparks, but I guess all that rust kept then a bit insulated.😅
@anascottwelding17615 ай бұрын
Why were you letting the 12v, 10A input alligator clips rub n touch so much, it was stressing me out. 😮 ?@Electronic_For_You
@Electronic_For_You5 ай бұрын
I didn't have lab Power supply back then 🤦
@ruelbustillos362317 күн бұрын
Is this can be used in 24v 140watts mini ricecooker?
@Electronic_For_You17 күн бұрын
If your coocker is 140W can be used this Module
@RobertDickens200215 күн бұрын
Not if you cant get amps above 2 it won't @@Electronic_For_You
@FernandoSouzadroid Жыл бұрын
Hello, I use a step down for lamps, in total they consume a maximum of 8a, but the charge controller varies the input voltage between 14.4 and 12.5, so it reaches 11v and the lamps become weak, I wanted to add this step up the video before step down, and raise the voltage to 16v, does this work?
@Electronic_For_You Жыл бұрын
You should use a Buck-boost Converter if you need stable Voltage
@FernandoSouzadroid Жыл бұрын
Thank you very much for the answer, I couldn't find a 20a buck-boost at a good price, and as I already have the step down, I thought about putting the step up before it, do you think it could be a problem? If the input voltage varies, does the output voltage remain stable?@@Electronic_For_You
@Electronic_For_You11 ай бұрын
I modified this boost converter to Buck-boost, you can try
@rishad1002 жыл бұрын
#1 😀 . Nice boost module ❤️❤️❤️
@Electronic_For_You2 жыл бұрын
But it doesn't work properly Not recommend to buy 😊
@rishad1002 жыл бұрын
@@Electronic_For_You thanks 🙂👍
@vaibhavbansal87412 жыл бұрын
Yeah it was 400w but can't deliver 40w , i think it runs hot , u can try put a fan
@Electronic_For_You2 жыл бұрын
@@vaibhavbansal8741 😂 Even current registration didn't work properly
@getbettersoonbroo Жыл бұрын
Is it good to charge 48v scooter battery with MPPT from solar input?
@Electronic_For_You Жыл бұрын
I think Lithium Ion batteries are very sensitive. So i can't recommend you to do that !
@Valentinshh18 күн бұрын
If it has a respective BMS, yes, but if it doesn't have one, I wouldn't recommend it. Remember that since you have more consumption at the output depending on the voltage at the input, you will have double, you should limit it.
@AkiiLesy3Ай бұрын
Thanks for the video, what if i don't need the Constant current, current may depend on the load, thanks
@Electronic_For_YouАй бұрын
Then you should increase the current to maximum
@Eksands Жыл бұрын
current adjust never works for me. I ordered 3 different already and I get no output difference when I rotate the current limit screw
@Electronic_For_You Жыл бұрын
The current regulator actually doesn't regulate current , it will drop voltage, this function is useless in boost mode
@De-tw7by2 жыл бұрын
Can you recommend any other unit which I can buy with similar spec and short circuit protection. Thanks
@Electronic_For_You2 жыл бұрын
I think XL4015 converter is better
@De-tw7by2 жыл бұрын
@@Electronic_For_You you mean XL 4016
@Electronic_For_You2 жыл бұрын
Sorry not that I recommend ( 250W 10A Led driver boost converter ) CC/CV
@pault931411 ай бұрын
@@Electronic_For_You I've tried that one, it gets ridiuclously hot. I had 3 of them all the same and very noisey
@emmanuelpeter065 Жыл бұрын
Is only a boost converter or also a buck converter
@Electronic_For_You Жыл бұрын
Only boost
@hamasmalik2 ай бұрын
I want to ask how many maximum amperes I can get from this at 12v input and 24v output = ? 19v input and 24v output = ?
@Electronic_For_You2 ай бұрын
12V Input 24V output 5A 19V input 24V output 8A
@hamasmalik2 ай бұрын
@@Electronic_For_You bundle of thanks
@Electronic_For_You2 ай бұрын
You are welcome ✨
@farhanmeo4992 ай бұрын
9v input output 13v maximum amps?
@Electronic_For_You2 ай бұрын
You should use 12v minimum input, 9V doesn't work well
@murraymadness46747 ай бұрын
I have some bad ones. I have another one that was working fine, but after turning the current adjust all the way it now does not work right. I checked with the other one I have that works, and the pot on the bad one shows 3.2k ohms between end terminals, whereas my good one shows 300ohms. So I think pot is broken.
@Electronic_For_You7 ай бұрын
Maybe mine is also bad
@murraymadness46747 ай бұрын
I took it apart today, and the pot is ok, there is something else wrong with it.
@moturcu4226 Жыл бұрын
Isn't this just for battery charging we can't use it in a motor for example?
@Electronic_For_You Жыл бұрын
You can use this to run a motor . But I don't recommend running sensitive electronic devices
@moturcu4226 Жыл бұрын
@@Electronic_For_You Thanks.
@Electronic_For_You Жыл бұрын
You are welcome 😊
@mhdgs99447 ай бұрын
I want to buy it to charge a 50 volt capacitor bank for a coil gun I'm making, I've made a zvs driver to charge the capacitors and I ended up blowing the mosfets. I'm thinking of buying this converter because it gives me a bit more room to charge them to 60 volts rather than 50, the capacitors can handle 50+15 volt over charge. The converter will. Be ran at 55volts most likely at a current of 2 amps, is it a good idea to buy it,
@Electronic_For_You7 ай бұрын
Use a resistor at output of boost converter, because the peak current can reach Upto 50Amps while charging the capacitors, it may blow up MOSFETs!
@mhdgs99447 ай бұрын
@@Electronic_For_You yeah I know I had placed a 20ohm resistor because it kept tripping my power supplies short circuit protection lol, thanks a lot
@Electronic_For_You7 ай бұрын
🤔 Try using a car headlight,
@ahmedkaram402 жыл бұрын
Can it be made?
@Electronic_For_You2 жыл бұрын
Yeas I make different one using NE555
@ahmedkaram402 жыл бұрын
@@Electronic_For_You Can you send a link to the manufacture of this device to me?
@Electronic_For_You2 жыл бұрын
Which one?
@ahmedkaram402 жыл бұрын
@@Electronic_For_You Circuit that controls 50 volts and 20 amps
@ahmedkaram402 жыл бұрын
@@Electronic_For_You Or the same circuit diagram
@tahirawan6285 Жыл бұрын
Sir we built own boost converter uc3842 and use 80nf70 mosfet and drive 32 volt led 50 watt but good sized heat sink is too hot only for 2 minuts whyyyy explain sir
@Electronic_For_You Жыл бұрын
You need to check the output signal with the oscilloscope , its outputting correct signal or not
@jannredreal78572 ай бұрын
Can i used this to power my 12v fan? With the input of 7v? does it fine to work? I hope somebody can answer this
@Electronic_For_You2 ай бұрын
It shows minimum 9V input, I think it will not work!
@mamatadas24698 ай бұрын
Can i use it to voltage up...like dc 1.5 volt to dc 3.7 volt??
@Electronic_For_You8 ай бұрын
Minimum input 9V
@naingtheawperc3817 Жыл бұрын
Which cheap boost converter would you recmand? In my country people are using this module to build and sell diy laptop power bank.Nothing has blown up so far
@Electronic_For_You Жыл бұрын
In my case it creates huge voltage spikes at output so i can't recommend this one , there are more converters online
@a2ztrader Жыл бұрын
I have 12v 5a as input, the output voltage is only 1.16v. How is that possible. The potentiometer is not working at all. I guess I got a bad one. Damn it
@Electronic_For_You Жыл бұрын
Hello, Check the fuse maybe its blown
@a2ztrader Жыл бұрын
@@Electronic_For_You fuse is ok i think. It has continuity
@Electronic_For_You Жыл бұрын
Maybe the controller ic TL494 has problem
@a2ztrader Жыл бұрын
@@Electronic_For_You but it still outputs 1+ V. And I can adjust it +0.08 V. Do you think that's the problem?
@Electronic_For_You Жыл бұрын
If the input is 12V then the output will be 12V minimum, 🤔 I think there is something broken maybe the diode , check the diode
@newvio19364 ай бұрын
I really wanted to buy this because of the constant current feature to charge lithium ion batteries with BMS, I watched your video regarding about modifying this module, would that be possible if i did what you did and charge the batteries with it? Actually i did ordered one of these
@Electronic_For_You4 ай бұрын
Yes it would be better if you modify this to buck Boost Converter
@newvio19364 ай бұрын
@@Electronic_For_You thanks!, Subbed!
@vamshikrishna7945Ай бұрын
@@Electronic_For_You can i use this module for diy lifepo4 charge purpose, i have 12v 3 amp charger buy using this module ok ?
@Electronic_For_YouАй бұрын
For battery charging you should use a buck boost Converter with current controlling capabilities
@Felix-tz1tk Жыл бұрын
Please help (1) I want use buckboost converter as a backup for my 19v Dell laptop (90W power max) using a 12v car battery. Could you tell me which is the best module for this task. (2) For my 12v 3A router, which would be the best buckboost converter, same battery. Thanks in advance.
@Electronic_For_You Жыл бұрын
LTC-3780 Buck-boost works great, you can try, but it cost a little more
@aanmenge1445 Жыл бұрын
can you power up the battery to the cdi motorbike or not, sir
@Electronic_For_You Жыл бұрын
Sorry I did not understand !
@LeopoldoFernandez-o9k2 ай бұрын
So pls teach us how to modify this..i bought one today new arrved from shoppee..😒
@Electronic_For_You2 ай бұрын
There is a video on my channel
@SamsMediaCenter Жыл бұрын
Hello, Thank you for the excellent video. I want an output of 30v, 15a to run the audio amplifier board. Please tell me how to achieve this? I have power adapter 19.5v 4.6a and 19.5v 6.7a. As you have explained, someone else that voltage increases and current decreases. So what is the best way or safe, stable way to get 30v 15a ? Using these step up modules voltage is increasing but how to increase current too? And get 15a? Or more? Please advise.
@Electronic_For_You Жыл бұрын
Your Adaptor is 19V 4.6A = 90Watt But you need 30V 15A = 450Watt So the voltage will increase to 30V but the output you will get only 90W so you get 30V 3A output only
@SamsMediaCenter Жыл бұрын
@@Electronic_For_You Thank you so much for the reply. Like you explained that is my dilemma. Please tell me how to achieve this? Is it possible using step up booster or do I have to buy 48v 20a and then step down to 30v 15a?
@Electronic_For_You Жыл бұрын
You don't need to step down or step up Buy A 36V 15A Powersupply then Adjust the potentiometer to 30V And You got 30V 15A Powersupply 👌🏻
@miorieser3210 Жыл бұрын
Kurzschluss am Input?
@Electronic_For_You Жыл бұрын
Can you comment in English please! 😊
@htunmyintaung18762 жыл бұрын
Is there any replacement mosfet for nce8290
@Electronic_For_You2 жыл бұрын
75N75 MOSFET (use Original)
@Scansoz Жыл бұрын
Can i run my laptop (19V 6A) with 12v 60A solar gel battery. Risk of damage to laptop?
@Electronic_For_You Жыл бұрын
Yeas , It can damage your laptop, don't use it , not recommend
@Scansoz Жыл бұрын
@@Electronic_For_You i'm cancelled my order, thank you. 🙏
@Electronic_For_You Жыл бұрын
Welcome You Saved your laptop 👌🏻
@Scansoz Жыл бұрын
@@Electronic_For_You i'm ordered *Aideepen 1200W 20A DC Converter Boost Car Step-up Power Supply Module Adjustable Voltage Converter 8-60V to 12-83V* what do you think?
@Electronic_For_You Жыл бұрын
I haven't checked that one so i can't tell its better or not
@albertogomeztobon2964 Жыл бұрын
Hola estoy en colombia cual es su precio y de donde es traído, gracias
@Electronic_For_You Жыл бұрын
I don't recommend buying this , it doesn't work well, but if you want to power Led lights , you can buy it from AliExpress, ebay
@golddetector012 жыл бұрын
Will this device increase the power directly from solar panels to the charge controller on cloudy days
@Electronic_For_You2 жыл бұрын
This device don't increase power it increase Voltage and decrease current I mean if you give input 12V 10A TheN The output will be 24V 4.5A and higher voltage lower current........!
@PIXscotland2 жыл бұрын
In some cases it may help. My eb70 power unit will only charge at 50w from a 12v supply. If I boost that 12v to 20v it can take 160w. This makes a huge difference when charging from the car power, but may still make a difference from a solar panel. If your solar panels are low voltage but high current then this could help a lot. There's no hard line where it will or won't help though.
@Electronic_For_You2 жыл бұрын
Right ✌️
@valtersouzaribeiro7612 жыл бұрын
Boa tarde parabens muito bom
@Electronic_For_You2 жыл бұрын
♥️
@kamranbatteryservice7923 Жыл бұрын
Same situations , I am facing too ! current boost adjustment is use less and dropping voltage on load . unfortunately I saw your video after buying this product
@Electronic_For_You Жыл бұрын
Oh .. it's too late ..!
@Imran-si8ln Жыл бұрын
Vai mera module ki input positive nagative shot ho gaya me keya karu😥 plz help me bro🙏
@Electronic_For_You Жыл бұрын
Check the MOSFET
@amarkumararak_b3651 Жыл бұрын
Bhai mere pass 12 volt ki battary he mujhe 24 volt Lena chahta hu boost chonvairtair modulai ko laga kar 12 volt input de kar 24 volt output le kar ise amplifiair chalaaya ja sakata hai ise battery par kisee cheej ka lod padhate hain ya nahin battery kharaab hotee hai ya nahin
@Electronic_For_You Жыл бұрын
Yeas But maximum 8-10A more not allowed
@amarkumararak_b3651 Жыл бұрын
@@Electronic_For_You @Technology Monotosh Bro bike ki 12 volt ki battary se input dekar 24 volt output lekar boost chonvairtair modulai use kar ke bike ki 12 volt battery kharab to nahin hogi battery main koi charging problem to nahin hogi
@Qwerty-x1n8s Жыл бұрын
Input 12v ar output 18v Nile koto amp out put pabo ar adjust Korte parbo
@Electronic_For_You Жыл бұрын
Yeas You can
@tcw8431 Жыл бұрын
HI, CAN U RECOMMEND SOME DC TO DC BOOST MODULE FOR ME? I BOUGHT TWO OF THIS BUT THEY ARE ALMOST BROKEN, ONE OUTPUT V WAS ONLY 0.2V, THE OTHER ONE WAS 17 TO 68V(I PREFER 10 TO 30V ,) I NEED UR RECOMMEN FOR BETTER MODULE Q.Q
@Electronic_For_You Жыл бұрын
12V Minimum input You can buy TL494 boost converter ( 400W 15A Boost Converter Module )
@tcw8431 Жыл бұрын
@@Electronic_For_You oh it was the module i bought,xD nboth of them was broken qq
@tcw8431 Жыл бұрын
I searching boosty module on taobao but less nice boost tmodule
@Electronic_For_You Жыл бұрын
Maybe you forget to regulate the current try set the current to maximum
@tcw8431 Жыл бұрын
@@Electronic_For_You ˊˋ i have set the curreny to the max and min but the same, maybe i would try to change the mosfet
@MresterSeedy5 ай бұрын
Hey can i convert 5v to 12v
@Electronic_For_You5 ай бұрын
I think 5V is too low,
@anascottwelding17615 ай бұрын
So it looks like it didn't perform 1/2 as good as it should.
@Electronic_For_You5 ай бұрын
Yeah , But ok for leds
@richardgumangan2129 ай бұрын
Make sure the sorce is not flactuating for stable supply and current and also make sure that the circuit is clean. Screw wire instead of clup and small solid tin wire.
@Electronic_For_You9 ай бұрын
It's good for powering Led lights only, i tried it many times the same problem always! I don't know if mine is faulty or all of them , use at your own risk!
@MACYNET323Ай бұрын
@@Electronic_For_Youso for power 24v led strips will work properly?
I think it's because of wire losses, if you use Thicker wire it would be more efficient
@mookednadee9304 Жыл бұрын
@@Electronic_For_You ok Thank you very much. I would try again with thicker wire than before time.
@Electronic_For_You Жыл бұрын
Good luck with your project 😀👍🏼
@mookednadee9304 Жыл бұрын
@@Electronic_For_You ok Very good. I can us over 2 hours thanks
@Electronic_For_You Жыл бұрын
That's good 👌🏼👍🏼
@deanp847 Жыл бұрын
Came here after it broke my voltage regulator. The aim was to step up my 48v supply to 53.3. Honestly it had a mind of its own, voltage was not stable at all. Ranging for 30 to 70+ spikes.
@Electronic_For_You Жыл бұрын
Ah so sad , if you watched it before buying!! It's very bad , can destroy Everything!!!
@KenanToker-cz2hb Жыл бұрын
Be sure to get output gnd from the output port, otherwise current adj. will not be possible.
@IcankDony-oe6gm Жыл бұрын
Bang punya saya kog gk bisa naik tgangannya tpi nyala..
@Electronic_For_You Жыл бұрын
Try increasing current first then voltage.... Maybe current is limited
@saranke9802 Жыл бұрын
I was ready to buy but thank you for the good video. It gives only 40W and get hot😅
@Electronic_For_You Жыл бұрын
Yeas It can also damage sensitive electronic
@Qwerty-x1n8s Жыл бұрын
Bro can I run 775 motor for a long time
@Electronic_For_You Жыл бұрын
Yeas
@Lucky84-11 Жыл бұрын
Lucky you got 1.5A, mine is .04A max
@geartech38608 ай бұрын
You only tested one module I think you just had a bad one I bought one and it worked fine
@Electronic_For_You8 ай бұрын
Really? 🤔
@jean47562 жыл бұрын
Not 400w... It is 120w realy Power ? Please
@Electronic_For_You2 жыл бұрын
Real power is 50-60W more is worst
@mehmetyuksel9465 Жыл бұрын
Helped not adjust current voltage step up work
@Electronic_For_You Жыл бұрын
Its not work like buck converter!!! It drops voltage as current registration
@mehmetyuksel9465 Жыл бұрын
@@Electronic_For_You which electronic component is faulty
@Electronic_For_You Жыл бұрын
It works like that ! No component is faulty! It doesn't limit the current actually. It will reduce the voltage instead!
@mehmetyuksel9465 Жыл бұрын
how can i solve this problem
@mehmetyuksel9465 Жыл бұрын
I can't decrease or increase the current as in the video, I turn the pot, the current does not change
@Electronic_For_You Жыл бұрын
*Maybe its faulty* Ask seller for replacement
@dantronics1682 Жыл бұрын
its a voltage boost converter, if you're increasing voltage then you will be decreasing the current
@KenanToker-cz2hb Жыл бұрын
Be sure to get output gnd from the output port, otherwise current adj. not possible.
@Electronic_For_You Жыл бұрын
Right
@16BITMEME2 жыл бұрын
Very good 💪
@Electronic_For_You2 жыл бұрын
😄
@oloyedeifeoluwa20726 ай бұрын
I don't think U should be adjusting the current or voltage with load on it
@Electronic_For_You6 ай бұрын
Without load how will you set the current?
@RobertDickens200215 күн бұрын
How else you gonna adjust it
@OldMarius-gn5kk Жыл бұрын
still a good boost converter below 40w
@Electronic_For_You Жыл бұрын
Its large in size and has many problem
@rnbeat2 жыл бұрын
i already Ordered this
@Electronic_For_You2 жыл бұрын
Don't use it For sensitive electronics
@rnbeat2 жыл бұрын
@@Electronic_For_You what about amplifier class D amplifier
@mehmetyuksel9465 Жыл бұрын
İt isnt worked current adjust
@Electronic_For_You Жыл бұрын
It doesn't limit the current. It limit the voltage
@fictionfiction5952 жыл бұрын
When i apply 12 v to 21watt load it give me 1,5A but i can't change current with cc pot can any one help me
@Electronic_For_You2 жыл бұрын
Maybe the current is limited by your Powersupply
@ankamanirudh883710 ай бұрын
Bad module, thanks I was about to buy
@Electronic_For_You10 ай бұрын
150W Version of boost converter Works well, I have a video you can watch!
@bashme334 Жыл бұрын
.
@Developer9817 ай бұрын
Bro in this video you have same problem your Device also don't go above 1.5amp how can i fix it
@Electronic_For_You7 ай бұрын
If your load doesn't draw more than 1.5A It will not output more than 1.5A