Lot of money that for a small gain, but it bet it’s very quick, I’ll leave mine at stage 1 😂😂
@piovo5222 Жыл бұрын
Yeah tbh it should be around the 500bhp mark as people have been running this type of setup now for years.
@Robdutton91 Жыл бұрын
@@piovo5222depends if you believe the dyno numbers
@DarksideDevelopments Жыл бұрын
@@piovo5222there are so many BS Dyno numbers in the BMW game.
@CYMRU619 Жыл бұрын
Wouldn't say 130bhp and 200 ft/lb increase is in any way a 'small gain'. The upgrades have a lot do with reliability as well as producing bigger numbers.
@piovo5222 Жыл бұрын
@@DarksideDevelopments like I’ve been telling you in the other comments the dragy runs prove the bhp levels
@paulsmith5696 Жыл бұрын
As I understand it the torque figure is more important than bhp, at over 1000nm I think that's impressive
@dkhan3233 Жыл бұрын
Correct this is my daily vehicle as i have a m2c thats stage 3 soo i asked more for torque then bhp and it flys from 50mph to 150mph
@bartselter5332 Жыл бұрын
100%! It’s all about torque with these diesels. Also, bhp is pretty much just the equation Torque x RPM / 5,252. (To get a rough figure). Props to DSD. Great content, and the video’s have an awesome vibe to them. Wish i would be situated closer to them…
@piovo5222 Жыл бұрын
@@dkhan3233you mind me asking what you paid for this service?
@stevenkerry3101 Жыл бұрын
someone must have extremely deep pockets because all that work with labor won't be cheap nice video 👍👍
@insidebyte8561 Жыл бұрын
Really needs the head porting to get any more out of them tbh, if you can get 400bhp out of a 1.9 tdi pd you should be able to get 500bhp easy enough out off them motors if the turbos is big enough.
@kilner79 Жыл бұрын
makes me wonder how much power can be achived from the 2.0 version of this engine the 6 cylinder is basically just the 4 cylinder with 2 extra cylinders
@piovo5222 Жыл бұрын
@@kilner79 you can get 300bhp reliably out of the N47, you can do a bit more but tbh your gonna be sinking in to much money at that point.
@trivax5852 Жыл бұрын
If you are interested, Austrian tuner DiTuPa runs and German tuner As performance are the gods of n57 and run far over 600hp in these engines
@MyRealName Жыл бұрын
@@piovo5222 Reliable and N47 can't fit into the same sentence. They're junk even when stock..
@LaunchDiadem41 Жыл бұрын
seems i'm pretty happy with my A6 BiTdi (CVUA) with my 420hp and 870Nm with only a Stage2+ tune on it 😅 still running EGTs with Darkside parts installed 👌🏼
@Spannerface Жыл бұрын
never seen a BiTdi even close to those figures with only mapping.
@LaunchDiadem41 Жыл бұрын
@@Spannerface Engine itself is Stock 😉 thats why it's called a Stage2+ and not Stage1 mapping only... on stage1 you get probably around 380Hp without having DPF related Problems... just for a example on Stage3 (like in this video) there are possible figures around of like 550hp and 1080Nm 😉 but then you'll also need a 90mm Dp because the Darkside one simply is to small for that... even on my tune i get a little bit of Boostcreep because of the flansh/pipe design from darkside 😅 so i'll exchange mine for a "better" one from polska
@radoslawrojek7032 Жыл бұрын
@@LaunchDiadem41which garage from PL ??
@LaunchDiadem41 Жыл бұрын
@@radoslawrojek7032 Software comes from TMR Germany (cb Tuning)
@gibba-349528 күн бұрын
Mine was stage 1 tuned to 425hp 800nm, don't ask me how but they did it and I've been driving around with those figures for over a year now, +-50k km
@DarksideDevelopments28 күн бұрын
Be interesting to see the dyno graph for that
@gibba-349528 күн бұрын
@@DarksideDevelopments I can send it if you want
@danielmarshall4587 Жыл бұрын
Bloody hell that "Paul" works like the clappers I hope my gaffer doesn't see this vid...... anyway enough of the silliness. Thank you for this, always good to see the workshop footage and a lovely car.
@nathangilmour4493 Жыл бұрын
Tune the gearbox on the bench, I do it all the time with my flex tool on jaguars , land rovers and other manufacturers that aren't bmw for xhp. Just remove the electrical plug and pin it, only 5 wires
@danielwarren2355 Жыл бұрын
Bets its a really quick car in yhe real world, but as a 435d owner, i personally couldn't justify anything more tjan than a map like i have
@nomad6638 Жыл бұрын
I'm disappointed, not one "Mental" in this post 😔 😁 Once again fellas, nice work 👍🏻
@abuhamzaa Жыл бұрын
A cooperation between you (Darkside Performance) and DITUPA would be very nice
@marcakko2010 Жыл бұрын
Impressive figures, Keep up the good work lads.
@sneekeruk Жыл бұрын
Would of expected more with it having fueling upgrades and other mods, theres 330d's in the high 400's and similar torque that are 10+ years older technology wise. Still wouldnt say no though, would be an amazing upgrade from my 320cd.
@DarksideDevelopments Жыл бұрын
Keep your eyes peeled, we've got something coming for the 20d's soon ;)
@echahly Жыл бұрын
Loving the content with danny, he's a natural good stuff hopefully someday i can bring a car down to Darkside for the proper treatment!
@kilner79 Жыл бұрын
the contents better than top gear love to see a series like the cheapest drag car and 3 or 4 of you each get one and do your own mods on a budget then go to a 1/4 mile track and give them death
@RealGX Жыл бұрын
Don't think you'll achieve 500bhp with hybrids to be honest. I think you need a large frame turbo to replace the bigger one.
@ryanp6138 Жыл бұрын
Tell all the other donkeys in the comments!
@piovo5222 Жыл бұрын
@@ryanp6138 Don't call us donkeys just because its your first time tuning a 35d to this level, many 35ds with over 500bhp with the same mods just different hybrids. Dragy proven as I know you could rig the dyno to make it pull over 500bhp.
@ryanp6138 Жыл бұрын
@@piovo5222 free Dyno if it does 500hp
@piovo5222 Жыл бұрын
@@ryanp6138 get some dragy numbers as we both know dyno figures really mean nothing when comparing cars. That car ran these numbers at the same mods but dynoed 553bhp in 335d x drive. 0-100 kmh 3.02s 100-200 km/h 6.9s 1/4 mile 10.68s@206.7km/h
@ryanp6138 Жыл бұрын
@@piovo5222 but you are slating our figures?
@mattiagaribaldi883010 ай бұрын
At that kind of torque arent the trasmission, shafts and axles at high risk of breaking?
@gsxr600rafii8 ай бұрын
We don't get awesome cars like that in the USA
@fluffpuckot Жыл бұрын
Good results! I would have thought cams would make more of a difference, but seems oem is quite good then. I guess the question is; a5 3.0tdi or 435d?
@DarksideDevelopments Жыл бұрын
We often see 10-20hp increase with cams, oem cams can handle it though. Depends what you're wanting out of a car really. Both can get big power numbers, but it's easier to do in a 30d/35d. 3.0 tdi is a mega platform though and sound better ;)
@RTC057 Жыл бұрын
It might be a daft question but when you removed the valve springs why didn’t the valves full into the cylinders? Thanks
@lukastyn Жыл бұрын
Engine turned over till the piston is at the top
@richardhunt1384 Жыл бұрын
Was thinking exactly the same question!! 😂😂
@honda.spares.man1 Жыл бұрын
Compressed air keeping them up
@dcggames Жыл бұрын
What was the limiting factor? Besides the TCU tune. Boost? Fuel? Temperature?
@DarksideDevelopments Жыл бұрын
Mainly boost, if adding more fuel it would then get hot.
@User.346803 ай бұрын
@@DarksideDevelopmentsHow much boost you have here?
@bartselter5332 Жыл бұрын
Torque graph looks very nice! Question tho, what is the backpressure at higher RPM?Also, it seems to fall off at the top end quite rapidly. Should have plenty fuel with; pump/injectors/cams. So i'm guessing the big hybrid turbo is the limiting factor at high RPM?
@DarksideDevelopments Жыл бұрын
It falls off rapidly because we're controlling exhaust heat, the backpressure at the exhaust manifold is 1.5 times higher than boost
@bartselter5332 Жыл бұрын
@@DarksideDevelopments thanks for the response! 1.5x the boost is fine.👍 what EGT does it max out during a strong pull? Also, i’m running m57 i know its not comparable. But what rail pressure is the n57 able to maintain with this power and these upgrades? Just curious about the platform! Last question, do you offer remote mapping? My car is running “fine” with the current stage 3 map, but i’m seriously considering DSD for a remap. Engine has done 5k KM’s now, has all the upgrades required to push almost 500hp and 1000nm. I’m able to do proper logging using Testo, and i’m able to read and write the ecu. If yes, i will contact you private. 👍 Thanks for your time, i’m located in The Netherlands.
@DarksideDevelopments Жыл бұрын
It was around 660 degrees in the downpipe. We do offer remote tuning, if you drop us an email to sales@darksidedevelopments.co.uk with your vin number and we can help you out through there 👍
@mitchellbathurst2688 Жыл бұрын
best part 10k for 40bhp over stage 2?
@piovo5222 Жыл бұрын
isn't stage 2 like 380bhp one these people just quote 400bhp cause of dodgy dynos.
@callumcurtis15 Жыл бұрын
@@piovo5222I thought stage 1 was around 380bhp ?
@modermonkula Жыл бұрын
Jesus Christ
@rajaahsankhan5926 Жыл бұрын
@@callumcurtis15 my 640d which was stage 1 dyno’d at 384.6 BHP Dpf and egr everything was still in place it’s exactly the same engine as this only thing changed was the gearbox and engine map
@DarksideDevelopments Жыл бұрын
@@rytiskurcinskas7179there are wild figures quoted all over the place for BMWs. We thought the VAG market was full of BS until we started on BMW
@fasteddy664 Жыл бұрын
I wonder what the cost per HP is for this.
@OfficialYeat Жыл бұрын
factor in most of these upgrades are to hold the power plus keep the reliability !
@fasteddy664 Жыл бұрын
@OfficialYeat I think a Stage 1 remap and maybe an upgraded intercooler to keep the temps a bit lower is the best value £ per hp. If you need more than that, an alternative platform is probably better value.
@fathead1968 Жыл бұрын
With all due respect, thats put me off hybrid upgrade to be honest. I was under the impression that 500bhp was acheivable with hybrids, intercooler and the deletes. Mine runs 385 with just the stage 1.
@fathead1968 Жыл бұрын
Thats also a low stock figure at 302, mine (335d) put out 325 on standard map. Stock is booked at 308?
@piovo5222 Жыл бұрын
@@fathead1968you dynod stock 325 because that persons dyno is over reading by 20bhp as a stage one is usually around 360-370 which makes your 385 to about 365 which is about right? All dynos are different all read different.
@fathead1968 Жыл бұрын
@@piovo5222 Thats oviously a possibility, it would be interesting to put it on another dyno, although dynos should be calibrated. The map I had was from Celtic tuning and they actually claim 400hp from stage 1. They said mine didn't acheive 400 as boost was 0.2 bar down.
@CJizzleJ11 ай бұрын
@@fathead1968They often claim figures that are bollocks mate to be honest
@rosskidd7243 Жыл бұрын
When doing valve springs is it possible for the valve to fall into the cylinder?
@trivax5852 Жыл бұрын
Theoretically yes
@migueljesus715811 ай бұрын
Interesting how most mappers with this type of setup can surpass the 500+hp but the "diesel specialists" can only get 446hp.
@DarksideDevelopments11 ай бұрын
Dodgy dyno numbers, if they've been on the dyno at all, especially in the BMW world. We'll happily put a "500+hp" BMW on our dyno to see if it really does those figures
@karolismarcinkus388110 ай бұрын
@@DarksideDevelopmentslet’s put mine on your dyno,when can i come?🤔 tuned by GKR performance
@karolismarcinkus388110 ай бұрын
@@DarksideDevelopmentsi can bring my bmw and i will let you do the dragy numbers and dyno numbers 😀if you say all 500hp bmws are fake dragy numbers😀
@User.346803 ай бұрын
What mods and car you have?@@karolismarcinkus3881
@user-zn4fd4vk1c10 ай бұрын
Darkside im in the market for a 435d xdrive but until i saw your 430d xdrive making even more power will i be saving more money getting a 430d to achieve your kind of power or should i just go with the 435d xdrive roughly what is the cost to get the 430d to this kind of power mate as i dont own one of these yet but need a pointer because i do want to get one and map it
@DarksideDevelopments10 ай бұрын
Yeah, we've got more out of a 430 so far. Depends how far you are wanting to go with it. We have a blog on tuning the 30d's here - www.darksidedevelopments.co.uk/Blog/tuning-the-bmw-x30d-n57n-n57d30a-30-diesel-engine/ Drop us an email to sales@darksidedevelopments.co.uk for costs including labour :)
@realmusicreallife Жыл бұрын
I have a x5 40d. Would i expect the same results if you guys did it
@DarksideDevelopments Жыл бұрын
Should be similar results yeah, drop us an email to sales@darksidedevelopments.co.uk with your reg/vin and we can quote power figures and costs for you
@G3LDY Жыл бұрын
seems easy to get the 400bhp out of these but to get that extra 50 its alot of work unless somthing is holding this back?
@DarksideDevelopments Жыл бұрын
We are looking at a larger downpipe, bigger intake and possibly a bigger FMIC next. After that we might need to look at a larger turbo
@G3LDY Жыл бұрын
nice love how much work you guys put into develpment, @@DarksideDevelopments
@danialmahmud4260 Жыл бұрын
Uncle deans famous 🫶
@user-mx3be1jy8u3 ай бұрын
Is it really worth stressing these N57 engines?. I see M57 cars holding their money for what they are, E6x, E9x 535d, 635d and 535d all fetch a pretty penny due to the reputation the M57 has for durability once you take the swirl flaps out of the equation. However I hear the bottom end is a bit weak on the N57 engines, coupled with the timing chain failures, hence the reason fancy 6 series 640d's are selling for stupidly cheap money vs their E63 635d counterparts. If I had one of these N57 jobbies I would be leaving it standard and dropping the oil every 6k miles to try and prevent the disaster of spun main bearings and chain failures.
@DarksideDevelopments3 ай бұрын
We've done a few high powered N57's now and not really had any issues with them. A couple of them have been driven for a good few years with over 1000Nm torque and are still holding strong so
@TomRopez Жыл бұрын
Did you mean nm not flbs?
@DarksideDevelopments Жыл бұрын
No, Dyno measures in lbsft. In NM it's just over 1000Nm
@TomRopez Жыл бұрын
Crazy!!! Be careful not to turn back time.
@lewisconnell1234 Жыл бұрын
What's the limitation for more power on this
@DarksideDevelopments Жыл бұрын
We are looking at a larger downpipe, bigger intake and possibly a bigger FMIC next. After that we might need to look at a larger turbo.
@alaindunkerque59 Жыл бұрын
Belle vidéo 👌 😉
@hyper8545 Жыл бұрын
Sick
@stanxx7693 Жыл бұрын
what kind of setup i have to be to achieve 350hp on diesel? i have now 2014 430d with tune and upgraded intercooler? and i want reliability too.
@DarksideDevelopments Жыл бұрын
Drop us an email with your VIN and we can quote on what is required 👍 sales@darksidedevelopments.co.uk
@user-gy2vc2st2v2 ай бұрын
What kind of coin does a job like this cost?
@DarksideDevelopments2 ай бұрын
Drop us an email to sales@darksidedevelopments.co.uk with reg/vin for costs
@alanmcgivern797 Жыл бұрын
Is it worth all that money for an extra 80bhp or so?
@DarksideDevelopments Жыл бұрын
The next one did better.
@hali2375 Жыл бұрын
Do you tunes Mercs ?
@DarksideDevelopments Жыл бұрын
We don't unfortunately, just vag/bmw/mini/porsche
@chrisp4899 Жыл бұрын
Should rebadge it "445d"
@Sj1bby Жыл бұрын
I'm wondering how many people will be beaching about you keeping the log manifold and how inefficient that's supposed to be.. What I'm really wondering about is how long wmi will last? I know this depends on the driving style and volume of the tank.
@kilner79 Жыл бұрын
water meth is a waste imo its ok if you do 1/4 mile now and again or just a bhp booster on a dyno day other than that its really not worth it minimal power and you have to maintain it once had a check valve fail on mine due to corosion and it flooded the engine and another time an earth wire rubbed onto the chassis causing the pump to start working this was a devils own kit tho and i did email teh company about the major flaw that all it needed was an earth and the pump would start that emptied a full 5l into the boost pipe and again when i started the car instant hydro lock its really not somthing i would ever put on a car again
@otacon4065 Жыл бұрын
Torque converter? Is the a G series then? I get confused with the non M3/4 models not having the horrific new grilles... As the E/F had 8 speed dct zf didn't they... So annoying the chinese moaned about 'violent' fast shifts of a dual clutch and now they have laggy torque converters... This'd be so much faster with a dct sigh.
@DarksideDevelopments Жыл бұрын
It's an F series with a zf8 and torque converter. Gearbox tune helps with the shifting making it quick and smooth
@otacon4065 Жыл бұрын
@@DarksideDevelopments crazy I thought F would have been dct? did they only do that on the petrols/certain models then? or purely true M cars? sneaky swines!
@DarksideDevelopments Жыл бұрын
Yeah, believe it was just the M3/M4's etc that had dct
@piovo5222 Жыл бұрын
@@otacon4065ZF 8 torque converter is superior to the DCT in a diesel, much more cheaper to buy, more reliable and they hold more power stock. Few other things also.
@G3LDY Жыл бұрын
the new m cars all have the zf box they dont have dct anymore @@otacon4065
@user-dv7vk4xr3w Жыл бұрын
why did you upgraded the turbos if the stock 35d turbos will flow 450bhp? you on baby boost
@DarksideDevelopments Жыл бұрын
who says stock make 450? not us
@User.346807 ай бұрын
Stock turbos make 380-390hp max
@User.346804 ай бұрын
My f10 535d got 410hp with turbosystems stage 1 turbos and 3 bar of boost and car already smokes a bit so what are you talking about😅
@hansturpyn5455 Жыл бұрын
.....on private roads..... LFMAO 🤣🤣🤣🤣🤣😆😆
@zvonimirleko2131 Жыл бұрын
😊
@H6NTY435D Жыл бұрын
I don't mean no disrespect to the owner at all, but im quite disappointed and flabbergasted with the figures, doesn't make sense!
@DarksideDevelopments Жыл бұрын
We too were hoping for more, but this is development. You cannot know the limitations until you try to surpass them. The customer was happy to trial these parts and in the end was ultimately happy with the performance of the car.
@H6NTY435D Жыл бұрын
@@DarksideDevelopments absolutely agree, don’t know until you try 😃
@marcakko2010 Жыл бұрын
1000nm of talk though that is still a very good increase from 750ish with stage one even though the horse power didn't go up from 370bhp ish with stage 1 . Still a decent improvement and I bet you can rely feel the shove from that now . Omg 1000nm would love to test drive that .
@davidlawickiii882 Жыл бұрын
Every build is their own but I could never bring myself to run meth injection on anything - straight boost/tune for me please.
@Chrisvrscrx Жыл бұрын
Bring back Ryan or Scott
@DarksideDevelopments Жыл бұрын
They're both the same person really
@DarksideDevelopments Жыл бұрын
When the time comes, Ryan will appear on your screen. But Danny will still be there too