4L60E SHIFT PROBLEM FIXED

Today we install a Corvette servo in my Cadillac Escalade. This is a very simple upgrade anyone with a 4L60E should do!

[@Americas450R]

I just did mine I got the corvette servo/long pin kit for my 2008 suburban and it's like a new transmission. I had a terrible double shift when going to 2nd and now nice and firm quick shift😊

[@seanmc8340]

What a gem of a video can't wait to try it!

[@RonDeezie]

Thank you so much praise God for people like you. You save me so much money and so much time. I rebuild a transmission for a 2001 F150 One Time by watching KZbin. God bless you guys and I really appreciate the hard work that you put forth in the time that it takes through these videos

[@bradroth2249]

Thanks! 05 Escalade with 145K shifts so much better. My part cost $40 and I had to disassemble piston/pin assembly in the car due to tighter clearance. Cutting the old blue o-ring and pulling it out was necessary to remove cap also. Great video.

[@slow_restoration]

It's worth the effort! Thanks for watching!

[@wendellgray7009]

What's the name of that part

[@lm7bird680]

i put a 6.0 from an escalade into my brother's '92 silverado and while the engine is great and performs like a beast the transmission has been a letdown. it always seems to be caught between gears and slips when shifting. hopefully a corvette servo allows it to unlock its full potential

[@ryandolinar2623]

My escalade with 195,000 miles had a 2 to 3 shift that was slipping everytime and could not grab the gear. I was worried I would need an expensive transmission rebuild. I put in the corvette servo and it completely solved the problem. It was a bit of a headache to get the snap ring back on. A tip if you have that issue, tap the cap in lightly with a hammer. Im at about 500 miles on the new servo. Im crossing my fingers the slipping issue is solved for a good amount of time to come.

[@marleyjoyner2097]

Still holding up?

[@kylel4689]

Still working good !??

[@ryandolinar2623]

@@kylel4689 The fix turned out to be a "band aid" in my case. It lasted for maybe 2,000 miles then the transmission could not shift into 3rd or 4th gear at all. I hoped I would get a little more out of it than that. I wound up getting the transmission completely rebuilt. I have about 6 ,000 - 7,0000 miles on that rebuild and it is still running perfectly fine, no issues, but it of course came with the cost of a rebuild.

[@ryandolinar2623]

@@marleyjoyner2097 Sorry I didn't see you question until now Marley. See my reply below if you're still considering doing this. In my case it just was a band aid fix.

[@micahyarbrough5513]

This really helped with the very loose shifting in my Suburban. It was cheap and only took a couple of hours to replace. I had to break the blue O-ring to get the cap out as others mention. I just a long cross-state drive through the mountains and shifting was nice and crisp.

[@mu9627]

I am finishing a fresh rebuild on 02 tahoe 4x4 4l60E. Frictions and seals were good and it worked fine beforehand, yet had to do rear main seal after 240k miles finally and figured it was out, so freshen it up. Using Sonnax pinless accumulators, sunshell, boost valve, reman valve body etc. Replaced planetary, old rear had some play in pinions. Used Sonnax hardened backing and apply plates with 65E 7 friction set up. Instaling Sonnax 4th super hold servo and was contiplating on whether to use the corvette servo as not looking for harsh 1-2 shift in normal driving. Under acceleration or when towing, that's okay. Had a shift kit in my old A body, turbo 350, best second gear 'skirt' even at part throttle and loved it, yet this is family hauler too. Thoughts appreciated and thankful for internet as had to drive around to different shops and get to know them for info in old days.

[@Hizenbird]

I just received an 03 tahoe from sister. Learning tips and tricks. In the process now of changing transmission fluid/filter. It has 228K miles. After reading your post I wonder: Should I be looking at what you have been doing? Should I be making these same repairs? Odds are this Tahoe was not being kept up.

[@mu9627]

@@Hizenbird Depends on how much down time to can afford. If it's 4wd there's more involvement too. I took mine down for a year as not able so much these days. Plus what it takes for each day to keep up. Some of the things I did that were either maintenance or failed that also helped make it easier, where taking the intake off, resealing the lifter valley cover seeping, replaced knock sensors, both had corrosion front was worse, and new boot/harness as connectors fell apart. I replaced the cam sensor, oil pressure sensor while it was off along with new fuel injector orings, cleaned throttle body, new sensor for it as they can take out a trans like the old TV cables would do on the earlier 700s. Also, had several broken exhaust studs on manifolds. With the cat pipe out of the way anyhow, I removed the exhaust manifolds to repair/remove broken bolts, upgraded back with newer style 03 up bolts from GM. With intake and exhaust out of the way ( along with inner fender liners), it made my life easier to get to and ultimately reinstall the upper brackets/bolt/studs upon reassembly. Yeah, most will figure overkill, yet I've done a fair amount of restoration to it over the past few years and cleaned/waxed/derusted and painted back bolts, brackets, hidden areas. Also replaced split loom plastic tubing around main harnesses on drivers side due to exhaust heat and rewrapped with 3M black tape. Looks like factory. R & I'd valve covers, replace valve guide seals using rope method as has plenty of access and could see a bit of oil residue build up on the exhaust valves, etc. etc. Aside from that, I did a lot of reading and watching videos, combined with my years in automotive, although never built many transmissions, yet been around it, and took on the challenge. I'm glad I did as it drives like new again. Considering I saved up on parts over the last few years, rebuilt the front steering and suspension and complete brake system, all new GM mounts, new universal joints, etc. Rebuilding the 4L60E does take some patience and there are many area's that can make or break the build. I had to save up to gather parts, then when the job began I ended making many changes as I'd had more time in between to study and learn more. I went from a, "Put it back stock", mentality to a true purpose built unit that should withstand any towing and miles I could put on it, plus to pass along to my son. The newer vehicles today, all well and good for most folks, have too many controlled/connected functions and are getting overcomplicated IMO, neat as they may be, I chose to continue to invest in this one. Keeping all receipts in case some dummy totals it, Lord forbid please on that. Okay, so on the build I acquired the tools slowly as I progressed online from various venders. I also rebuilt my transfer case while out too, same thing. Transmission bench has a great video series, then there are so many others too. Sonnax has a great deal of technical information, there are a variety of mods that can be done, yet make sure they are done in conjunction with the build purpose. Mine's not a drag car nor will it be street raced, etc. Just for it to shift properly and be reliable especially if towing. I did build up a 2 - 4 servo setup with all new GM components, new pin, cover, 2 & 4 pistons, GM scarf rings, springs, etc. as concerned about having too harsh shift in second, especially like in slow/stop n go traffic. However, I also built up a spare 2 - 4 setup, all new parts including another new GM center pin, yet with a Corvette servo and super hold 4th servo and got it all together while transmission was still out and set up the apply clearance to within spec by properly grinding the pin to length with the correct radius by chucking it in a drill and using a disc grinder, carefully!. Now that I know that it works and how it shifts, I may put that set up in it when we go to tow a camper. If it makes 2nd shift like third does now, I'll be very happy as it's quick and firm under mild to heavy acceleration. Don't leave out the small things, TCC valve, boost valve, 3rd check ball capsule - mine looked okay and didn't leak, yet when I removed and compared it to new GM unit, the ball seat was wallered out and wouldn't have lasted too much longer without giving problems. Again, so much to put down and so many others who've actually done this for a living will have their say too. All I can say is for the cost of a reasonable custom build elsewhere, this thing is now up to 4l65/70 standards. Yes, that includes new old stock GM 5 pinion planetaries, not aftermarket or rebuilt stuff. All the Sonnax I could put into it, lol. Including one of their reman valve bodies. I used Rock Auto and many other venders by shopping for best prices to keep costs down and again saved up over the years in anticipation, glad to still get N.O.S components for this vehicle. I was very fortunate as prices have gone up a bit since I started collecting. All said and done, It's my personal vehicle, it's now back on the road and I have the personal pride of knowing that I did it and if anything ever comes up, I know how to check it out and how it operates. Hopefully that won't be anytime soon. Hope this helps others and any additions to this will only solidify the DIY of these transmission's and GMT 800's.

[@Hizenbird]

@@mu9627 Wow! That sounds like quite an experience. Over the last few days I just changed a bunch of fluids in my car that desperately needed attention. My rx300 (daily driver) has 285K miles. I changed Trans fluid and filter, engine oil and filter, Front Diff. fluid, Rear Diff. fluid, power steering fluid. It was quite a bit of work. My brothers sees this and comes out and says, "I hope there is some benefit to you doing all this work." I explain to him that I'm not just changing fluids. I extending the life of my car, I'm saving money, I'm building patience, perseverance, critical thinking skills, and creativity skills, not to mention more knowledge about the thing that I heavily rely on. Good on you for going through that process. I hope I'm able to do the same.

[@frankmonte437]

great video, greatly appreciate you sharing your knowledge and perfect video ...thanks, when thanks alone really isn't even enough !!!!

[@billshirk8207]

Great video alot of useful info in 25 minutes. thanks for describing the tools you use. keep up the great work.

[@slow_restoration]

Thanks for the support!

[@123_tweet]

sir i have a jerk in 1 gear and same jerk in gear frm 2 to 1 will this fix help my car?

[@finniewilliams6095]

Thank you, Sir for this very easy, articulate, step by step instructional video.

[@slow_restoration]

Glad it was helpful! Thanks for watching.

[@finniewilliams6095]

@@slow_restoration I have an 04 Suburban 1500. I was able to follow along and change out the servo. Although it shifts a little better, it’s still not trustworthy. I intend to use a bottle of Lucus stop slip and if that doesn’t solve the issue, I’ll weigh the cost difference between a repair and a replacement. Unless you can provide any other probable solutions. I’m an amateur….

[@finniewilliams6095]

@@slow_restoration How important is it to replace the throttle body sensor if I am experiencing shift problems? How likely (without you having diagnosed my transmission) will the throttle body sensor solve the issue?

[@kenspear5077]

I like the how to videos. Thanks Danny.

[@jennyloughry896]

Awesome video as always. Wish you would have done like a before and after under decent acceleration though.

[@slow_restoration]

Yeah, I tried! It didn't come out very good in video for some reason! Thanks

[@AliasAnde]

Thanks for the demonstration. Doing this in a Trailblazer and there's not enough room so I did have to lower the transmission...Would love to know how you (or some tip) replaced the final snap ring to finish this.

[@armands774]

Definitely gonna give it a go on my 99 jimmy

[@franklyczewski9372]

Great help for slushy shifting 😎😎

[@chrissexton6697]

Doesn’t seem too hard to do. The lift definitely makes it lil easier

[@kenweerts3869]

Ordered the parts, plan to do the fix this week, thanks for the informative video.

[@user-bf7ex5mt7v]

Did it work

[@TheManofYah]

What's the part number

[@kenweerts3869]

yes@@user-bf7ex5mt7v

[@kenweerts3869]

nonidea, picked it up a a parts store@@TheManofYah

[@thomasmorgan3491]

Great video THANKS!

[@shanewright6958]

Great job and great video 👍👍

[@frankoneyjr.4515]

Great video !

[@user-zu4gd5uf5h]

What does it mean when your 4L60E won't shift from 2nd to 3rd but only sometimes? Never slips and no codes.

[@BoNewberry]

Liked before watching it. Thank you!

[@SteveKeddy2009]

If you had overheated your transmission would that inner spring likely would have a different spring constant now and should possibly be replaced?

[@roderrickgaston5939]

Awesome video! I have a question. I have a 2004 Cadillac Escalade and it has 155xxx. It runs and drives fine but per my research I do hear that the transmissions in them tend to heat up and fry pretty quick. I don't do any hard shifts or anything but do you suggest changing (not flushing) the transmission fluid for safe keeping? I hear some mechanics say that they're ticking time bombs and others say changing the fluid and filter is better for it in the long run.

[@bradroth2249]

I would change the fluid and filter of fluid doesn't smell burnt. Could also add auxiliary transmission cooler if worried.

[@michaelbimbo5549]

Should I Pair this with also doing my 1-2 accumulator

[@stacysmith9080]

Very nice video...Bravo

[@slow_restoration]

Thanks for visiting

[@robpaul7900]

Which part did you use which company normal size pin and normal spring?

[@juanmartinez-ed6bd]

Nice video ,It would,ve been nicer if you had an over view camera....👍👍👍

[@jesusvalladares2803]

I have a 2004 GMC Sierra and I have a little sleep between 2to 3rd gear, I'm pretty sure This is the solution for my truck and your video helps me a lot to do my truck, It is a really good video, my question Is how I can found this in Amazon do you have any part number or something

[@slow_restoration]

Thanks, just search Corvette servo in Amazon. There's several sellers that sell this. amzn.to/3PhB9Wx

[@jamesjohnson-tf6px]

My 04 Tahoe - on my 4trans- still not have 2,3 & 4tj- occasionally it’ll go to high gear - dunno really what to do now

[@shanebryan8151]

Absolutely terrific video my friend thank you very much. I'm having rather I believe a similar issue I have a 99 Chevy Silverado 1500 2 wheel drive and the transmission is rather skipping 2nd and 4th gear do you code come up that the shift solenoid was bad so I put two new solenoid and it today and it's still doing the same thing the question is do you think that this Corvette Servo would be my issue I would very much like your opinion and again thank you very very much for this video

[@mikedukes8448]

Check the ground wire connection from transmission to frame and ECM to firewall.. bad poor ground causes it to go in to limp mode common problem 4l60 e and silverado

[@iintegragsr00]

Great video very easy to understand. .,….I got 2006 Chevy suburban 4x4 same shifting problems. Shifting just like say. What you think should I buy the parts l that you replace?

[@slow_restoration]

Thanks 👍

[@daeshonkaine3172]

Amazon 💪🏿

[@alienistic]

I ordered the corvette shift servo from Amazon (Fully assembled unit incl cover $63) and this did not fix the problem, I suspect ours may be a total pump failure. We had the same issue described in the video, long double shift 1st to 2nd, and very slow 4-5 second shift 2nd to 3rd, we bought our Escalade exactly 1 year ago with this problem and have driven it this long so most likely not a clutch friction plate issue. A few days before replacing the shift servo the vehicle completely lost ability to shift to any gear but still worked in 1st gear. After replacing the servo it restored shift 1st to 2nd back to doing its strange double shift again, but unable to shift 2nd to 3rd or beyond.

[@berlnberln5289]

3-4 clutch is pretty weak on the 4l60e unfortunately, if you drive around with a leaking internal seal or any clutch slip you will fry the 3-4 clutches eventually and will need to replace them.

[@cliftondrew5979]

Someone try to still my 2004 chev 1500 and now my transmission won’t change and I just put a brand new one in my truck what could it be

[@Valdemar-Perez-III]

I love that slow restoration hoodie.

[@robr4596]

if going to this point, why didn't you drop the pan and change the filter? not capping on ya, but I would have done a service as the vehicle is already on the lift.

[@slow_restoration]

It was just done! Did that first before this arrived.

[@adrianlott622]

Will this stop a slipping transmission ?

[@chrishansen7004]

So kind of a problem here I'm trying to do this on my 03 Sierra I get too the last part of the servo but the end of the pin hits on part of the truck and I can't get it out

[@robpaul7900]

Did u ever solve your problem what was the issue?

[@maddmavic]

What is the part number to find this ?

[@WhatisLifeAbout]

Having hard shifts when slowing to enter a roundabout and accelerating coming out of the roundabout. Also sometimes after slowing to go over a speed bump and then accelerating once I get off the speed bump. 2008 suburban k1500 Ltz

[@blayzer2889]

!

[@panagiotisf7228]

Can we get a link to the exact kit?

[@mattc2094]

Hey thanks for your video. One question, does this fix help the shift from gear 1 to 2? I’m experiencing a real sluggish shift from 1 to 2... Seems to hang around the 1500 rpm mark for a few seconds, before finally shifting into 2.

[@slow_restoration]

It's definitely worth a try! It's not a guaranteed fix, but it usually drastically improves the shifts. For the price I would go for it!

[@danielcarrillo9122]

I have the same problem with my yukon 2005 can you tell me what is the name of the part

[@slow_restoration]

700R4 4L60E Corvette Servo www.amazon.com/dp/B0081H7E58?ref=ppx_pop_mob_ap_share

[@DOORBELLBOY11]

My Tahoe raises up rpm to about 3000 then shifts but doesn’t do it if I’m cruising

[@brandenbarror6726]

Matt c did you try fixing it and did it work haveing the same problem from 1st to 2nd

[@user-cd2bh7lm1c]

I have 2003 hummer h2 that had slipping shift from 3-4 with 175k miles on it. I tried the vette servo and now it won’t drive at all. So I put the old one back in and still no movement. Any ideas as what happened?

[@slow_restoration]

Maybe time for a rebuild. I would double check the fluid level as always first.

[@duckvit5488]

thanks

[@vasquez81]

Would this cause my Tahoe to major delay shift ir feel like it drops into neural?

[@slow_restoration]

This helps that a lot.

[@brandongovlogs4336]

Hey Danny hopefully u can help me, I have a Cadillac Escalade ext 07 and literally today a few hrs ago I tried to put it on drive and it stayed on Neutral; the gear stick would go all the way up and down but the truck would stay on N, Idk what could be, could be a shift cable broken or a shift interlock? Help!

[@slow_restoration]

If the shifter moves without any detents and there's very little resistance it's a good possibility its in the cable or it came unhooked. This would be easy to check if you can get under it and look at the trans linkage. Just make sure the wheels are chocked.

[@leemartinez4323]

Quick question. My 07 Avalanche just went to limp mode and would only drive in gear 1 and 2. Not 3 or D. Checked the fluid and was completely dry. Added trans fluid and no difference except I now have a slow leak and I can shift to 3 and D when my speed gets up. So I have to manually shit to D and has very little power. And I recently just been pulling a trailer over the weekend moving.

[@workingmansrestorations7071]

I just bought an 03 escalade i have shift problem. Have to let up to shift to second.

[@slow_restoration]

Try this servo, should make a difference.

[@AlexanderRodriguez-pk4cg]

Thanks for the video, My truck stop pulling while driving and only move at first start after it get warm it will not shift. Is this a servo problem.

[@slow_restoration]

Sounds a little more serious.

[@GhostGats]

Did you ever figure out the issues I’m currently having that same isssue when the trans warms up it doesn’t shift

[@AlexanderRodriguez-pk4cg]

@@GhostGats yeah the gears are worn out

[@idoc152273]

02 Chevy Suburban and I'm starting to believe AAMCO failed to repair my transmission. A custom rebuilt transmission($2909.09) and the transmission is still seem to slip as I give it gas attempting to increase my speed from 45 to 50. Now with this rebuilt transmission I can come to a complete stop, give it some gas to go and the transmission slips before going into gear. Going back in the morning to complain about the repair not being fixed.

[@slow_restoration]

Definitely take it back!

[@mu9627]

What did you find out? Believe would help many if you let us know. Thank you.

[@marcosmarcos5758]

Ammo it's just a brand.

[@Fdeubcfhbbjhfd]

The problem is you went to AAMCO lol

[@Hizenbird]

If my tranny fluid smells really burnt is it too late to think that this will fix anything? The car still shifts from 1 to 2 but 2 to 3 or 3 to 4 revs up before switching gears. I drove it about 10 miles not knowing that the fluid was really low.

[@slow_restoration]

Probably too late at this point.

[@1977TA]

I have a 2001 Trans Am. Do you know if these cars came from the factory already equipped with the Corvette servo?

[@slow_restoration]

I don't think so.

[@jjcastillo1436]

Is this on Ford escape awesome

[@javierochoa432]

My Cadillac Escalade reverse is slipping…any ideas to fix it or just replace transmission?

[@slow_restoration]

If it's slipping, probably needs a rebuild.

[@maddmavic]

Did they make these for a 6 L Yukon Dinali all wheel drive

[@slow_restoration]

Yes, same part!

[@planetdisclosure-filesdocs7018]

would this cause my automatic shifting to fail ? i have to shift manually on my 05 avalanche 4l60e, no codes or check engine light appears.any advice?

[@nathanlangellier9402]

Same problem advice?

[@planetdisclosure-filesdocs7018]

Input forward Sprag -

[@planetdisclosure-filesdocs7018]

What kind of truck.

[@richardcournoyer1473]

mine has hard bang shift 2nd and 3rd is that the solenoids inside the pans?

[@slow_restoration]

Hard to say, have you installed the servo?

[@seantire]

Can I please have the amazon link for this?

[@slow_restoration]

www.amazon.com/dp/B0081H7E58/ref=cm_sw_r_cp_apa_i_qK.9EbMMQWR7Y

[@handsomeransom2235]

Plz quik question...how many catalytic converters are on there?

[@slow_restoration]

No problem, this one has 2.

[@handsomeransom2235]

@@slow_restoration goodlookin out mane

[@edwardjames1369]

3 and 4 th gears are not shifting 1st and second still going.

[@greyhairedmountainbiker116]

Awesome! can you do this on a 4.3L S Blazer?

[@slow_restoration]

Yes you can!

[@majanydeschamps8920]

is there enough space on a 06 tahoe ? has anyone done it on that

[@slow_restoration]

Yes there is.

[@tylerj2710]

lets get started with that it has 226k miles and hes working on the transmission for a 20 dollar part.

[@kimberlyanne8549]

Eh. Mine has 339k on the original motor and transmission and I'm just now replacing shift solenoids. I didn't have any transmission problems other than the occasional wierd shift until I let it sit a year through quarantine. The shift issue wasn't bad enough to be worth fooling with before, but since I have to get under there to fix the other issue now I may as well check this out. There's no time for a rebuild or money for a replacement, so we'll see if this can get me to work and back for awhile longer... Wish me luck, send good vibes, and don't bad mouth my high-mileage truck. 😆 Until I get this one right, I'm having to drive a Ford that was bought as a project. It gets me where I need to go, but not with any degree of comfort or dignity. The damned driver's door stuck yesterday and I had to choose the window or passenger side exit. FYI, I tried both - neither can be done gracefully when coworkers are watching. 🤣

[@mecharenacorrupt1055]

Mine had 315,000 when the I did the shift solenoids, kept on driving like a champ for 1 year til it got stolen

[@technoeridict6558]

My 94 Cadillac fleetwood won’t go into 4th just rev bombs third

[@xaysaysombath6453]

Hello Sir, i got 2005 cadillac Escalade esv i has the transmission Rebuild in the pasted 5 years last month the Engine is Bad and I let the Mechanic do the Engine Swap and then I drove home about 15 miles I'm about 2 miles away from my house then the Transmission is start to Acting up just like in this video and I kept drove it about 1/4 mile Now the transmission is free even I put in any Gears it won't move at all. Do you Think the Corvett Servo is Bad? Help me Please Sir. i had been spented a lots of Money into this car in the last 5 years. It's over $6000 Already so far in the pass 5 years.

[@slow_restoration]

I would check the fluid level first! The servo won't stop it from moving.

[@xaysaysombath6453]

@@slow_restoration Sir, i'm puting everything back together now but i having a trouble putting on the snap Ring. snap ring is a last thing right? push in a Servo and force in the snap ring until it lock Right? Please help me Sir, Thanks!

[@slow_restoration]

@@xaysaysombath6453 Push the servo cover in and the snap ring should pop right on. Be gentle but you may have to push it in with a pry bar.

[@agentoidomann7968]

@@xaysaysombath6453 how did it go?

[@danakothrade4091]

Does this only apply between first and second or would it also help soft shifts between two and three as well as three and four no slipping once engaged, but when transitioning from 2 to 3 and 3 to 4 sit slips

[@JoeyDaBull]

my 07 tahoe is slipping between 2-3 and sometimes bangs hard into gear moving the vehicle forward.. started happening after a bad ground was causing stalls and misfires.. makes me hate all this computer crap, but i want to try and tune it out using software.. make it shift sooner or later to solve it..

[@hiramnegrete6397]

Got a 2007 escalade 1 and 2nd gear is slipping sometimes can it be this

[@slow_restoration]

This would fix a 1-2 shift issue, not after it shifts. 2007 also uses a different transmission.

[@robpaul7900]

Will I have enough room to take it out and put new one in? It looks tight I have a 4wd Silverado 2001 ext cab.

[@slow_restoration]

You should, it's tight but I haven't found one, yet you can't do.

[@drejohnson2157]

Having the same problem in my 2003 EXT I’m doing mine this weekend let you know how it goes.. also how do we fix that airbag light? 🤣

[@duplexflame1646]

I thought the Escalades had the 4l65e? Is that a base model?

[@slow_restoration]

Same basic trans, almost everything is interchangeable.

[@nathangregory9002]

He clearly said it had a 65 in the video. They are the same trans with minor differences

[@joeycoe6125]

is there a part #, wanting to buy it

[@slow_restoration]

Just search Corvette servo.

[@haijihambrick9319]

I have a 96 caprice lt1 just bought it drove it all the way from Montana to Ohio without any problems it drove sweet few day later I seen a drip then few more days later a puddle and it wouldn't shift out of second gear then I had to keep cutting car of start back up go a lil bit and same thing but bad leack should I do lines filter flush an corvette servo please help car road perfect until it start leaking started as a drip then puddle and put computer on it and it said pcm??????? Please help

[@costafortia]

Any updates on the transmission performance?

[@slow_restoration]

Still going strong, unfortunately the Escalade got rearended and totaled. Trans was good though.

[@stevenhammerle]

@@slow_restoration 😥

[@mrmann4557]

Will a transmission shift rough if your tensioner pulley is bad?

[@slow_restoration]

Not usually, but if it's keeping it from charging proper it could. Voltage is important.

[@maxthemadtuner]

Thanks for sharing.

[@rickrudolph8964]

ok...ive been involved in this project for 6 weeks now....thankfully its not my daily driver. road grime had yhis thing allmost like welded into place. Then last week.it actually moved for me and i got it out. now i cant seem to get this thing in deep enuff to put the covers snap ring back on....it will go but be patient. im thinking my crowbars the tool to use instead of the pry bar....i came down with lyme the same day i got the servo out so the fevers wreaking havoc with me. The fluids just horrible though. not cooked, yet but pretty bad.....so how can i drain the converter safely? ive done this with th350s back in the day by cutting the top feed trans line on the radiator ....couple 3ft pieces of fuel line. the end i left in the radiator i put the line into my new fluid....the other end off the tranny was just to empty it all out. my rebuilds a vette servo now and i used to use trick shift alot too back on the 80s....is this ok with the 4l60e? and lucas too. my trannys were better than new and trickshifts allmost like putting in a shift kit too. I got my scripts for lyme today and im feeling my oats allready after just the 1st pill....im not working till sunday so theres time. Its thurs now. pretty excited sbout this whole thing...its my 01 silverado and i miss it

[@gabrielsliwa4708]

My trans is shifting in gear on tell i idle 1.5 rm then it shift normal drive fine only cold start

[@haijihambrick9319]

Would that keep it from shift

[@raphaelgluzman4933]

Great video. I like to tie my e-clips with dental flaws string so they don't go flying across the shop

[@blackericdenice]

I tried the corvette servo bs. That’s not the correct way to fix a 4L60e. I had to remove the valve body and replace the separate plate.

[@nyc1655]

I just did that too same bs hard 1-2 shift

[@kristopherhasenbuhler5393]

I'm probably gonna try that and the accumulator valve.

[@blackericdenice]

@@nyc1655 What kind of truck?

[@themoyers1605]

what issues might you have if this piece goes out or is going out?

[@slow_restoration]

Sluggish, delayed first to second shifts.

[@hectorchavez514]

Amanda your so beautiful.

[@chrisb9028]

Does this work on a 6L80E 6-Speed

[@slow_restoration]

It does not.

[@user-gl3hz5ty3h]

How do i take it off it wont even move in a bit its stuck!

[@slow_restoration]

Spray it down with some penetrating fluid. It might already be pushed in, try moving it around.

[@rockabichebel]

nice video and explain I give you like .. I have hummer h3 2006 l5 I change the engine to 6.0 I one guy tern my 4l60 from l5 to v8 he change the bell housing and torque convert and pump and shaft.. now I have it on my hummer I have a 1 problem take a litle time between D n R need a little more Rpm 2 slow shifting between 1n 2 and 2n 3 3 when I press on the pedal and I have down shifting from 3 to 2 my RPM go a little high plz you can help me what to do ? thank you for your help

[@slow_restoration]

Not sure, could need some tuning or may need a rebuild.

[@simplybeautiful4098]

It would be nice if u had focus on the speed or accelerate at least up to 100 to show the difference between when you did the test drive & after great video but not convinced that it works with driving same speed limit but u sound true cause the part was worn out just saying

[@slow_restoration]

It's hard to film, it's more of a feel as it shifts. Thanks

[@simplybeautiful4098]

Am just going to purchase 1 for my wife today with 337000km previous owner said. Needs transmission 😆

[@paulgallegos3305]

Will this work 2007 escalade

[@slow_restoration]

No, they have a 6 speed trans that is different.

[@illustr8phee100]

does your caddy.. shift lil hard from 1st to 2nd?

[@calvinlayport3127]

Only problem is your video would of been much of could of shot the video from the top looking down at your work other then that great video

[@slow_restoration]

Still working on improving, it's tough when you're working and filming. Thanks for the suggestion.

[@sontoshaynes4639]

Great information but mostly was looking at your gloves better angle plz so we can actually see as you work

[@slow_restoration]

Thanks, I did do a updated version with better camera angles. It's a tough spot to film in.

[@haijihambrick9319]

From shifting

[@Orefamilylawncare]

Sad part is EVERYTHING else in a 4l60 wears out and causes other problems.

[@slow_restoration]

Very true!

[@samuelmarchese121]

It's a problematic transmission but if you can troubleshoot it very reliable.

[@DillonTurner395]

Servicing helps. Lettings that old worn out fluid try to lube things for 200k+ just aint the game. That said even one without regular servicing ive seen some hit nearly 300k before failure. These arent as horrible transmissions as people make them out to be. Infact ive seen more fail are higher mileage due to low fluid levels. Transfer case input seal goes bad then you end up with a good portion of your trans fluid, in your transfer case.

[@nobullshit9721]

@@DillonTurner395true there pretty reliable if you don’t beat them and change the fluids

[@MeaHeaR]

will it work on mie vs commodore

[@tommavrakos]

Can't wait to see a video.too fix my 92 chevy van 4l80e doesn't shift into 3rd or 4th.in lim mode.showed code 81,82. 2 master mechanics cannot figure it out.of and on problem for years

[@treslongwell1332]

so your only symptom was "sluggish shift?" Not sure what that means. I was going to replace all of my solenoids, but this looks much easier . I want to believe.

[@bradroth2249]

Just did my servo today on a creeper. Fixed mushy shifts on my 05 Escalade with 145k.

[@glendonhines9022]

@@bradroth2249did it work

[@DavidRamirez-ds6fl]

What is the part called?

[@richcoccaro2177]

Great content. However, this dude would do himself a favor by getting a bench to work off of. Doing this servo breakdown and rebuild on a piece of cardboard stretched across the engine bay of a truck hulk is a bit prehistoric. Good stuff though.

[@slow_restoration]

LOL, just showing anyone can do it!

[@jimmieroan9881]

its the quality of work done, not how shiny and pretty your tools are. i see a desk that looks like it was just bought it tells me the guy does no work. i would love to have had a work bench and lifts and all the other goodies but most of us use what we have.

[@tomasmartinez7349]

Add a corvette servo

[@slow_restoration]

Hmmmmm.... That is literally what the video is about!

[@jimbradley727]

Huh...

[@oldmansilas559]

From the clean look of the undercarriage. He’s definitely not in the northeast.

[@slow_restoration]

Pennsylvania, I guess a little bit south of northeast.

[@oldmansilas559]

@@slow_restoration No, that counts as northeast. That’s incredible that the undercarriage is that clean.

[@blackericdenice]

An Escalade is too large to have a Corvette servo installed. If you really want to help people fix their transmission. You tell them to drop the pan and change the filter first.

[@slow_restoration]

The filter was done before this as stated, it works good now with the servo!

[@blackericdenice]

@@slow_restoration After a while, you will get tired of the hard shift to 2nd gear at full throttle. Drop the valve body, take it apart, clean it and replace the separator plate. Buy new "stock" servo seals and it want lose pressure anymore.

[@dakotasmith9604]

@@blackericdenice I just bout a remanufactured trans and it does not even have 300 miles on it do u think doing the servo would fix my problems

[@blackericdenice]

@@dakotasmith9604 No you need to return the unit.

[@oldmanmtb1443]

A Escalade is too large to have a Corvette servo that dont even make sense....do you even know what that servo is for...

[@nyc1655]

Didn’t fix my hard 1-2 shift

[@slow_restoration]

It's not supposed to. It helps with soft, sliding shifts!

[@banno6938]

The CV Servo affects the into 2 & 4th gear shifts making them "claimed" firmer & quicker . Very likely , you have an issue inside your valve body or 2nd gear accumulator .

[@mydaddy7690]

Try replacing your 1-2 accumulator

[@Orefamilylawncare]

That's because it's actually a worn accumulator /pin

[@testmcgee9230]

Is your harsh 1-2 shift intermittent? If so, it could be a wiring harness problem. Actually even if it’s not intermittent that can be true. Try disconnecting and reconnecting the wiring harness connection to the transmission to remove any oxidation and improve the contact. Free to do and not so difficult.