53" Titan 2 Plotter/Cutter Set Up: Live

Plotters: flexfilmstore....
FlexCut Software: flexfilmstore....
If you're interested in any of the tools I used in the video, view our products below:
Tool Kit: flexfilmstore....
Beginner Tools: flexfilmstore....
Best Selling: flexfilmstore....
Flexfilm is a window film distributor dedicated to providing top-tier ceramic and carbon window film, superb tools, and unmatched customer service and support.
Shop window film, tools, plotters, and more:
Shop online 24/7: www.flexfilmsto...
Phone: [phone]
Stay connected with us:
Instagram: / flexfilmtint
Facebook: / flexfilmtint
Don't forget to subscribe to our KZbin channel!

[@danielpadilla635]

Hey Ralph thanks for this video Just got my titan 2 and this helped me out setting it all up … What blade did you use in this video??

[@d12windowtintingllc]

This plotter is really good for window tints ?

[@JeosvanySanchez-mf3pf]

Great explanation sir thank u so much 🙏

[@mellowtonen7316]

Thank you so much for this video!

[@joshhalsey8477]

I have the titan 3 and I love it

[@jackcausby1165]

How do you put the grit rollers where you want them

[@jamiebyrd5334]

Is there a way to make the cutting head come to the starting point at the end of each cut?

[@FlexFilmPlus]

Yes. Take the slack out of the roll so it doesn't pull the film and cause the shift under the pinch rollers when it jerks.

[@d12windowtintingllc]

Do you suggest

[@mannymercado514]

I’m on my way to pick up a used titan 3 I’m wondering if it’s compatible with window film?

[@FlexFilmPlus]

Yes but only with a few softwares. Most pattern software does not work.

[@MrChevyman12]

Hey Ralph, I think the software has an adjustment somewhere to push the film out further after the cut is complete. I have seen it but can't find it again, I am sure tech support would be able to state where you can find it.

[@MrChevyman12]

Also, I have started to add teflon tape on top of the teflon strip about 2 layers, I just remove the tape as necessary as it is cheaper than the strip.

[@MrChevyman12]

Another tip, I just use some scrap tint and cut the tint on the table using the blade holder to get it close prior to installing it in the plotter...again, the teflon strip is important and although not expensive, it's not cheap to if you have to replace it often.

[@ismaelayala4283]

question,why you dont want the blade to cut the liner too?

[@FlexFilmPlus]

If you cut all the way through, you will lose the structure of the film. Everything will crumble and fall apart and or rip the carriage off the machine.

[@ismaelayala4283]

@@FlexFilmPlus thanks for your answer

[@overflowvinyl]

Is there any particular reason why you're using the oval instead of the test button (square and triangle)? Wouldn't the test button waste less material? Very helpful video though. More helpful than any of US Cutter's instructions. We're going to use this method the next time we have to change the blade.

[@klopjui]

Omg thank you 🙏🏿

[@jesusvaldez2248]

Instead of removing and afjusting the blade, why didnt you just adjust the forced pf the blade

[@MrChevyman12]

The force is more of a fine tune adjustment. You start with your blade adjustment around the 90g force range and then start adjusting force up as you need.

[@d12windowtintingllc]

Do you advice to buy this potter for window tints installation?

[@AlejandroCruzCar]

90g is too deep for vinyl. Haven't found a recommended chart for materials.

[@surefiremushroomsmicrogreens]

I will never buy a titan 3 again. They are junk especially when the warranty runs out. I will be going with Graphtec or Roland best brands and products in the industry.

[@FlexFilmPlus]

I have all three brands

[@isaiahwillis5082]

You sell these plotters for 4k on your website but on uscutter you can get them for 1600$ lol

[@FlexFilmPlus]

You have to have a code to get them 60% off on our website.