#58 DIY electric board - It's my new beast pt.1

This video is about #58 DIY electric board - It's my new beast pt.1
E-mail - [e-mail]
INSTA - / kamijuins
MUSIC BY Till - This right here
1.Deck - bustinboards.c...
2.Motor - diyelectricska...
3.Truck - diyelectricska...
4.Motor mount - diyelectricska...
5.Truck clamp - diyelectricska...
6.Motor pulley - diyelectricska...
7.wheel - www.amazon.com...
8.wheel pulley - www.diyeboard.c...
9.Belt - diyelectricska...
10.ESC - flipsky.net/co...
11.Remote - flipsky.net/co...
12.Switch - flipsky.net/co...
13.Battery - hobbyking.com/...
14.Connectors - flipsky.net/co...

[@KAMiJUINs]

영상속에서는 순조로워보이지만 변수가 많은 작업이었습니다.시간도 생각보다 많이 걸렸구요. 하지만 처음부터 끝까지 조립해봐서 뿌듯합니다. DIY전동보드를 계획하신다면 이 영상이 도움이 되었으면 합니다 :-) 6:55 에 나온 모터 전선 커넥트에 열 수축 튜뷰가 완전히 감싸지 않았는데 이부분은 완전히 감싸야 합니다. 6:55 This part is wrong. The connection have to be fully covered with a tube. The video looked good, but there were more variables than I thought. And I needed more time than I thought. But I had a sense of accomplishment because I assembled them with my own hands from beginning to end.I hope this will help if someone tries something similar.

[@bitmammothOG]

thank you! this is a great build and very inspiring :)

[@KAMiJUINs]

@@bitmammothOG Thank you for watching :)

[@Laureloke]

This is bad idea to put LiPo under board. Your board has low clirance, so your "off-road" wheels are only suitable for flat road without holes and stones. Looks nice, but not for all roads.

[@KAMiJUINs]

@@Laureloke There is no problem in my environment that I usually. But generally you are right. I'll try to change some of parts. It will be made to suit the more general use environment. (Actually, I didn't expect so many people to see this video. And the wheel was used for appearance rather than function.) Thank you for watching :)

[@user-ce2dr5vb9y]

How many money u spend on this project. If this a not secret ?)

[@adityaaurora9869]

ladies and gentlemen of the jury, you've got to get a hold of yourselves

[@lolosolodolo1]

Wow I scrolled past this comment right as it said it in the song. Super surreal feeling to read something that is also background music.

[@Livefreeman]

my verdict of this project, not guilty, good job

[@KAMiJUINs]

Thank you so much :)

[@dangerdave3135]

Ladies and gentlemen of the jury gotta get ahold of themselves geeez

[@KUfraskins]

This was extremely well done and helpful to all builders

[@KAMiJUINs]

Thank you for watching :)

[@tinmant4127]

This is probably one of the coolest and most informative diy e skate builds I have seen. Good Job on just showing us how to do it without all the unessasary repetitive word vomit most DIYers videos have. Good edits as well. You didn't waste time on the video, but I know it took a long time to edit and make everything look clean like you did. I checked out your part 2 on this build as well, and the directness in your cost on all parts with total was great as well. Test ride was great with speed and acceleration as well. Over a big thumbs up!

[@KAMiJUINs]

Thank you soooooo much :)

[@thomascoble3741]

That music drove me crazy

[@Sailor2752]

Same! It got a little annoying

[@stevegek]

But what's the verdict?

[@knownuser09]

@@stevegek Verdict fuck that shit music off next time.

[@kimbow7216]

AGREED. TURN THAT SHIT OFF.

[@augustlee4400]

you better get ahold of yourself

[@andrewstang-green3107]

I Love it! I would suggest larger wheels for more clearance to the battery.

[@KAMiJUINs]

Thank you for watching ;) and visit.

[@chrisrathjan1501]

Sweet build. I like the boxes they suit it really nicely. You have some good ideas. Thanks for the credit hahaha not at all necessary. I found vibration still gets through but it helps a little bit. That will be so much power! I suggest you get some Lipo alarms. If one cell goes bad you need to know about it. This is going to be epic.

[@KAMiJUINs]

Thank you so much for using your idea, :-) and thank you for your suggestion (ºㅁº)=b

[@leboiffic01]

Hi Kami, I would really thank you for this video, which is probably the most acurated that we can found on the net. With your help, I ordered all parts for my moutain board, based on your configuration and it’s work very well !! There is now more than 1 month that I ride everyday with it, in my little corner of France and it’s really so fun !!! I’m now looking for a method to use 4 x Lipo to extend my maximum distance avoided. 😀 One more time, many thanks for your videos an for the quality of them. Take care of you ... we are now awaiting about the next

[@KAMiJUINs]

Merci beaucoup d'avoir aimé ma vidéo. De nos jours, je suis tellement occupé par mon travail personnel. Donc je ne peux pas faire des vidéos pour un moment. J'espère que vous serez toujours en sécurité.

[@vinnypal783]

You know what? You make the art of board building look simple enough and you probably got a lot of people off their butts to pursue this one little dream of theirs, I sincerely admire you for the effect you have had on people...your boards are fundamentally sound, and if they were sold retail, I would certainly want to purchase one. I think they would be great for those of us who have owned an evolve maybe, but have not the desire to pursue the DIY route for the eventual upgrade. This board are for those who are committed to the idea of travelling in an Electric vehicle, as if that was the normal thing to do, in the near future.

[@KAMiJUINs]

Thank you so much for saying that :) Bro~

[@vinnypal783]

@@KAMiJUINs Thank you for sharing your board building with us, I am also a DIY Eboard Enthusiast and am currently in the middle of getting parts for my own beast. I get a lot of inspiration from the boards you build. You are so clean and precise with your approach and your boards speak for themselves!

[@ulmuhide]

님 정체가.. 전기, 기기, 부붐을 고르는 것부터 다루는 디테일까지 못하는게 없네요. 이렇게 다방면으로 다 할 수 있는건 정말 대단한건데. 정체가 뭐예요

[@KAMiJUINs]

저도 여기에 관심갖게 되면서 공부했어요, 유튭영상이나 자료도 많이 찾아 봤구요~ :-) 좋게봐주시고 또 시청해주셔서 감사합니다.

[@donmimo2011]

Nice music. Cute dog. Great job. You are a genius.

[@KAMiJUINs]

Thank you for watching :)

[@MonkeyMagick]

You have some good skills there. Well done. Look forward to seeing the next part!

[@KAMiJUINs]

Thank you for watching :)

[@Snap123S]

Nice build! It kind of looks like my board but you have waaaaay better parts 😅😄 keep up the good work!

[@KAMiJUINs]

I saw your DIY board~ Right :-) look quite similar and cool~. too, Thanks mate (ºㅁº)=b

[@kingesk8]

The build is so clean it’s it’s insane

[@KAMiJUINs]

Thank you for watching :)

[@UltramaticOrange]

Very clean build. I'm looking forward to the test ride video! You should check out the remote from Hoyt St. Electric Skate. It's a weird design, but very nice to use.

[@KAMiJUINs]

Thank you for visit :-) And i saw that a round thing.Thank you for your suggestion.~

[@NamezzemaN]

Nice! I admire your craftsmanship.

[@KAMiJUINs]

Thank you for watching :)

[@cityslick7]

Legit DYI 👍🏼. What kind of flex though with those boxes. Feel like your gonna hit stuff.

[@KAMiJUINs]

Thank you for watching :) Now, I've raised the boxes height slightly. video #65

[@ethanfeng8686]

Great built by using flipsky motor, and flipsky control kit, and my favorite deck. 😀😀

[@KAMiJUINs]

thank you for watching :-) and this motors are from Torque board ~ I like this deck too~

[@karlstern7877]

As a fellow esk-8 builder and diy-er I can say this thing will out-perform every boosted board and evolve and even my own builds. an fsesc 6.6 and 6380 motors at 12s is more than plenty for racing.

[@KAMiJUINs]

Thank you for watching :)

[@Pandadancypant]

Neatest and cleanest diy board I've seen to date. Nice job

[@KAMiJUINs]

Thank you for watching and visit :-)

[@smglsnk]

absolutely right! the best one so far... and the most beautiful. The whole bulid is inspiering. If and when I make one of my own... I'll do it like this. great job. Sorry for my English.

[@KAMiJUINs]

@@smglsnk Thank you for thinking that way :-)

[@mafu46]

Great build! I think it's sit to low from the ground

[@KAMiJUINs]

Thank you for watching :) It's okay where I usually ride, but in other places, I agree with you.~

[@ratheonhudson3311]

Beautiful step by step build! Looks great too

[@LordHaehnchen]

Nice! Sounds like a jetplane when firing up its engines ;) But your soldering technic makes me worrying a bit... Try to heat up the joints first and then adding the solder, like so the solder really flows inside the connection parts and is much more reliable...

[@KAMiJUINs]

Thank you for watching :) with your advice.

[@erickelly8704]

That's a banging board looks awe-SOME can't wait to see the maiden ride & hear those motors!

[@KAMiJUINs]

Thank you for watching ;)

[@dallaschase1462]

I appreciate all of your videos. I hope to build my first board soon. You've provided so much information in watching all of your tests. It will help me so much! Thank you!

[@KAMiJUINs]

No problem and I'm glad I can help you :-) Thank you for Watching my videos~

[@Pootski302]

Hey Kami! About the vesc tool, for your computer, did you have to download any drivers or any COM ports to your computer to recognize the vesc? It seems I’m having issues with my computer connecting to the vesc. I don’t know whether it is the cable (even though it came with the flipsky vesc) or the computer..

[@KAMiJUINs]

Well, I used a Windows version computer. And there was no problem. Shouldn't you make a video about the situation and contact Flipsky?

[@Pootski302]

KAMi JUINs I seem to have made a noob mistake. I tired using different cables and it ended up working on a windows 10 computer. Thanks for the reply though! Keep up the awesome videos, love your work!

[@user-js4yn9zz1i]

또 전동보드 만드셨군요!! 정말 부러워요ㅜㅠㅜ 날씨도 많이풀려서 한강에서 타면 크으,,최고져 얼른 파트2도 보고싶어요 기대되요!!!

[@KAMiJUINs]

시청 감사합니다~ :-) 요번은 좀 힘들었어요 ㅋㅋㅋ

[@BigKidsOfficial]

Solid build brotha! Was it me or did the wires on the flipsky seem hard to solder; they are so think! Seeing your dog makes me miss mine 🐶. My dog Fozzie unexpectedly passed last year 😪. Anyhow, love the build my friend and can't wait to see you hit the road with it! Keep up the great video! - Neil

[@KAMiJUINs]

Thank you for visit :-) I think, Fozie's gonna miss you a lot, too. And I saw your cute Fozie as Instagram. LOVELY Fozzie

[@ShaneCarrigan]

VERY COOL. great job and cool to watch. I look forward to seeing the cost breakdown and specs. Inspires me to do this. I ride an Evolve Bamboo GTX and I am curious about building my own knowing the parts can be sourced and you can craft it your own way :) The only things I wish my GTX had were replaceable batteries and the ability to reverse.

[@KAMiJUINs]

HAHA So do I :) Thank you for watching~

[@FalconPunch1978]

I just bought a bamboo gtr and it’s awesome but I would be perfectly happy with what you built. Nice work, well done.

[@KAMiJUINs]

Thank you for watching :)

[@warlockboyburns]

4wd 120mm hub motors has got to be the best board. I'm still waiting.

[@gregorypatzelt6964]

What a beautiful build and what an amazing and simple video. Keep up the great work. Love your deck of choice!!!

[@KAMiJUINs]

Thank you for watching~ :-)

[@udsmall7306]

Bustins are sweet! I just got a Rayne Rival and am toying with the idea of building it electric...but it's just so damn *pure* as a gravity freerider...

[@oliverbass2462]

Cool build! I would grab some metal zip ties for securing those wires in the back, plastic ones tend to wear quickly then snap

[@KAMiJUINs]

Thank you for watching with your advice :)

[@paul-erikhelliste4390]

Kami is so cute

[@KAMiJUINs]

Thank you :) KAMi will love you!

[@perryFBA]

Great build, you should definitely get batteries with a C rating higher, 12c is really low. You want minimum around 40c

[@KAMiJUINs]

Thank you for watching :-) and Thank you for letting me know.~

[@zzzul]

Best build EVER ‼️‼️

[@KAMiJUINs]

Thank you for watching~ :-)

[@paul-erikhelliste4390]

Kami juins i want to know whats the range for your new beast

[@KAMiJUINs]

It around 10miles.

[@godofcodgamer8296]

Omg I wish I can do this I would have one for each day but idk anything about electronics all those things!😪🥺 good job bro😁😎

[@paul-erikhelliste4390]

I love your videos their just amazing and i very like the boards you made

[@KAMiJUINs]

Thank you for saying that :)

[@anastach1]

this is art mate...good job, i love your style...the board is amazing...keep going

[@KAMiJUINs]

Thank you for watching :) and saying that~

[@kevinwhite825]

Very talented!! Nice work, super clean

[@JcXtreme72]

That did come out really clean. Good job.

[@KAMiJUINs]

Thank you for watching :)

[@GadgetInspektor]

Great work and cute dog. But I would definitely attach batteries and peripherals on top of the board. They are protected much better and the ground clearance isn’t compromised. I don’t see the need for using the entire surface for the feet on an electric board though.

[@KAMiJUINs]

Thank you for watching :) And I agree with those aspects. But I couldn't give up the appearance of the board in my standards. ㅜ..ㅜ

[@domobrah2671]

Beautiful build my friend! Very high quality!

[@KAMiJUINs]

Thank you for watching it :)

[@superbinchoi77]

요즘 까미주인님 영상 너무 재밌게 보고 있어요 그리고 전동보드 너무이뻐요 😍😍

[@KAMiJUINs]

아 ~ 좋게 봐 주셔서 감사합니다 :-)

[@superbinchoi77]

@@KAMiJUINs 😁😁

[@Nandox7]

Nice DIY buld! :) Now show us that thing rolling. Any reason why you did not use this time a DIYE motor mount and instead went for the torqueboards motor mount? (Just for convenience as you were getting remaining parts from there?)

[@KAMiJUINs]

Thank you for watching :-) At first, I just wanted to assemble it into torque parts. However it was found that double bolt for torque was more accurate than DIYE's one bolt.(The mount angle was constant and more compact.)

[@Nandox7]

Thanks for the explanation. The clamp you're using looks good but I can't see it in their site, the one you link seems to be different.

[@KAMiJUINs]

​@@Nandox7 Yes! looks like a different pic but same one. and you can buy combo it's bit cheaper. diyelectricskateboard.com/collections/electric-skateboard-motor-mounts/products/63mm-reverse-motor-mount-set

[@sillydopeyguy]

Very nice build. I'm sure someone has asked you but I was just wondering how much flex does the board have

[@KAMiJUINs]

Thank you for watching :) it's not flex so much for me. (i'm 64kg wight)

[@yanzodadon]

Your videos make it look easy to enjoy the simple things in life. I like watching your videos. Why did you choose the flipsky ESC over the focbox unity?

[@KAMiJUINs]

Thank you for watching and visit every time :-) Because I ordered Raptor 2.1 last December.

[@MaVeRiCk77]

@@KAMiJUINs 🤣

[@skraggle]

You did a great job with your build and also with your videos. Very impressive!

[@KAMiJUINs]

Thank you for watching and visit :-)

[@alltheboost5363]

Really cool build... I hope you don't run into any issues but those nutserts that you put in from underneath the board need to come in from the top of the board. so that way the lip has to pull through the wood. All it's going to take is a little bit of moisture and those nutserts are going to come out especially with those monster batteries. This video makes me want to build a board so bad. If you do run into issues with the nutserts falling out pull the grip tape off put them in through the top and then re grip tape it and you won't have any more issues. you can also put it in with a little bit of a binding agent far as an epoxy or something.

[@KAMiJUINs]

Thank you for watching with your suggestion :)

[@ujung5683]

오❗️ 그뤠잇 프로젝트였네요👍🏻👍🏻👍🏻👍🏻👍🏻오늘도 잘 봤습니다

[@KAMiJUINs]

네네 ㅎㅎ 힘들었습니다 ㅋ

[@alphazen3108]

How much😳such an awesome build love the attention to detail and you have a cool dog. 👍

[@KAMiJUINs]

Thank you for watching :)

[@Snap123S]

Cant wait to see some action on that monster!

[@KAMiJUINs]

Thank you for Watching :-)

[@mta3562]

Awesome build. I keep coming back to the video. I have couple questions if you don’t mind. 1. Where do you get the inserts that you put in the deck? Why did you chose to the reverse motor mount over the smaller one? Thanks in advance

[@KAMiJUINs]

The short one is caused by interference with the deck when a motor with a diameter of 63mm is used. and I bought the inserts from Amazon USA. Thank you :)

[@handdancin]

the threaded metal insert into the deck for mounting the boxes is genius! you could use a forstner bit and the hole would be easier i think

[@KAMiJUINs]

I agree with you. I'll buy one, if I have another to use it. Thank you for your suggestion. (I've already made a hole. When making this board) :-)

[@paul-erikhelliste4390]

But the build is so awesome. This build cost only 1300 dollars its so awesome

[@KAMiJUINs]

Thank you for watching :) Yeah it has superpower lol~

[@Bertoslav]

I don’t want to copy... but I might have to switch out to your deck... cause damn, it’s sharp. Gives me the chills it looks so good. I might go with a beercans aluminum board... I’m not sure.

[@KAMiJUINs]

Thank you for watching :) I recommend the deck.

[@jacobboone568]

did you just go to a nearby hardware store for the plastic sleeves and protection for the motors and esc wires?

[@grasiciel]

Kami this is a great board.

[@KAMiJUINs]

Thank you so much for saying that :)

[@dyb6916]

전 이제야 전동보드 입문했는데 정말 벌써부터 DIY 보드를 도전해보고 싶게 만드는 영상이네요 !! 저도 나중에 까미님 영상 참고해서 꼭 도전해보겠습니다 !!! 다음 영상이 너무 너무 기대 돼요 ㅠㅠㅠ 빨리 보고 싶습니다!!! 한국은 전동보드 영상이 많이 없는데 항상 좋은 영상 너무 감사드려요 ...!

[@KAMiJUINs]

아~ 그렇게 봐주셔서 감사합니다 :-)

[@dyb6916]

까미 주인님! 저도 드디어 미포보드가 왔는데 전원을 키면 미세한 바람소리가 나는데 약간 팬 돌아가는 소리처럼 나길래 궁금해서 열어보니까 딱히 팬이 보이진 않던데 원래 전원키면 전원부에서 바람소리가 나긴하나요...? 괜찮은건지 걱정되네요...

[@KAMiJUINs]

@@dyb6916 글세요? 제가 가진 보드들은 전원이 들어왔을때 소리가 나지 않았습니다. 하지만 제가 모든 보드의 ESC 특징을 아는 것이 아니라서 그 증상에 관해 제가 판단할 수는 없을것 같아요. 보통은 주행을 하면 모터와 ESC부분에 열이 발생하기는 합니다. 하지만 소리가 나는지까지는 저도 확인해 본적이 없네요 ㅡ..ㅡ' meepo 커스텀 서비스에 동영상 찍어서 메일로 물어보는것이 가장 빠를것 같아요.

[@dyb6916]

ㅎㅎㅎ답변 감사드립니다 다시 들어보니 전원부가 아니라 모터에서 나는 소리였어요.. 전원을 키면 모터에서 삐- 하는 소리가 나긴하는데 혹시 왜 그런지 아시나요..? 문제가 있나 걱정돼서 일단 영상찍어서 미포본사에 보내긴 했는데 구동중에 사고가 생길까봐 걱정이네요 ㅠㅠ

[@user-vh6eo3lh3u]

드뎌 기대하던 영상이 올라 왔네요 오랫동안 기다렸습니다

[@KAMiJUINs]

아 그러셨군요. 감사합니다~ :-) 즐겁게 봐주세요~

[@logicaldistraction]

awsome. good work! want to see you ride this thing :)

[@KAMiJUINs]

Thank you for watching :) and I will ~

[@ifrashable]

it looks cool, but please test it on a speed-bumpthe clearance looks very low, and does the board flex?

[@KAMiJUINs]

Thank you for visit :-) It's not flexible at all so i used 1/8" pad. And you are right. I have to test it safely.(it's a DIY hahaha)

[@user-vn8ft9kt5o]

편집도깔끔하고 보드도완벽합니다 ㅠㅠ감동 저도 만들어볼까 생각했는데 이런영상이있어 참 감사하게생각합니다

[@KAMiJUINs]

저도 시청해주셔서 감사합니다 :)

[@user-pv8ke6tp1r]

보드 무늬 특이하네요~ 근데 부품들은 비싸서... sd : 까미 귀여움 오늘도 한몫

[@dinokim3955]

보드 diy에 큰 도움이 될듯합니다. 좋은영상 고마워요

[@KAMiJUINs]

네, 시청감사합니다~

[@user-pv8ke6tp1r]

아내가 보드타는거에대해서 어떻게 생각하는지 궁금하네요 Q&A 영상 시작 전 잠깐 하는것도 재밌을듯...

[@user-pv8ke6tp1r]

보드가 집에 쌓일수록 아내 분노도 같이 쌓일텐데...

[@chrisnavarette6541]

Very impressive. this should have more views.

[@KAMiJUINs]

Thank you for watching :)

[@renars1480]

Do A test run, and it seems like ther is litle space from batarei to graund, othervise loks sick! Good job man!

[@KAMiJUINs]

Thank you for watching :)

[@__proto__.toString]

기다리던 영상이었습니다... 우선 추천부터 하고 시청할게요:)

[@KAMiJUINs]

아 그러셨군요~ :-) 즐겁게 시청하세요~

[@winning_tiger]

저도 전동보드를 직접 만들어보고싶어도 문과출신이라 그런지 뭐가 뭔지도 모르겠던데 대단하시네요 ㄷ ㄷ

[@KAMiJUINs]

시청해주셔서 감사합니다 :)

[@byoung-supark5896]

카미님, 영상 감사히 잘 보고 있습니다. 저도 보드DIY중인데요, 영상에 나오는 번데기너트? 규격 좀 알 수 있을까요? 숫놈 볼트는 길이 몇으로 사면 맞나요? M5번데가너트라고 검색해서 사면 될까요? 그리고 플라스틱통 고정하실 때 쓰신 ㄱ자 연결고리는 이름이 어찌되는지요. 거기에 사용하는 볼투 너트 규격 좀 알 수 있을까요? 질문 많이 드려서 죄송해요.

[@KAMiJUINs]

M4,M5가 나사와 너트의 지름규격을 표시하는 단위입니다. 인써트 너트와 볼트를 구매하실때 같은 단위로 통일하시면 됩니다. 인써트너트라고 검색하시면 되고 너트의 길이는 사용하실 데크의 두께를 고려하셔서 구매하시면 됩니다. (인서트너트 고정시 에폭시 본딩 필요합니다) ㄱ자연결고리의 경우 ㄱ자꺽쇠라고 검색하시면 될것 같습니다.

[@santosandchristy]

Its actually pretty cool ,but won't you have problems with objects hitting the items on the bottom of the board

[@KAMiJUINs]

Thank you for watching with your opinion :) I'm going to try to improve it one by one.

[@DaveChips]

It's beautiful... But I'm honestly way too afraid to ride those high performance boards 😅 Thumbs up! :D

[@KAMiJUINs]

Thank you for watching it :)

[@AVEJOTV]

Hi kami ... loved this build and Im taking a lot of inspiration from this for my next build... could I ask where did u buy the black wrap u used on the bottom of the deck??¿?? -Thank you and keep up the good work :)

[@KAMiJUINs]

Thank you for watching :) and should search for PU sheets on Amazon.

[@nathanaelmuller5306]

Where did you buy theses plastic box ? I love so much your build so satisfying to watch :p Thanks for the answer !

[@KAMiJUINs]

I got it from a household goods shop on the street.

[@nathanaelmuller5306]

@@KAMiJUINs alrigth thanks :)

[@doglabdogtraining-gus.8873]

Love the dog

[@KAMiJUINs]

Thank you for watching :)

[@naz95k71]

you should have bolted the case trough the deck, the mothod you used for the enclosures is too weak and it will fall off, allso using an steel/carbon fiber case would have been better, less chance of something damaging your bateries

[@KAMiJUINs]

Thank you for watching :) with your opinion~

[@Justagunguy]

I will literally pay you to build and ship something like this to me, that’s an awesome build. Just wow. 👍🏼

[@KAMiJUINs]

Thank you for watching :)

[@spkt0r]

Awesome Video thank you. you made me look forward to building my own.

[@KAMiJUINs]

Thank you for watching :) you can make a better one ~

[@termaddict]

Hi kami, can you please provide a link for the type of terminals you soldered to the ESC (6:42)? Thank you very much. Great videos!👍🏽

[@termaddict]

Also, if you could recommend a charger and BMS for this setup.

[@KAMiJUINs]

Thank you for watching :) All the parts links are under the description box. And I used a balance charger instead of a BMS. I tried to install a BMS, but it was difficult to find a good BMS that supports the 12s battery.

[@amanuelamanuel]

Love watching you build, You should start selling custom builds, I think you'd make alot of people happy!

[@KAMiJUINs]

Thank you for saying like that :)

[@dadjake]

Jesus Christ, two 6380 motors... That's a ton of torque right there.

[@KAMiJUINs]

Yes it's too much :) Thank you for watching ~

[@stefanofanfani8080]

Really good job!!!!!

[@KAMiJUINs]

Thank you for watching :)

[@adrianastro1]

Kind of concerning because there's not much ground clearance. Maybe but the board on top of the trucks instead?

[@KAMiJUINs]

Thank you for watching it. I've already tried that way :)

[@sunstart]

Hey quick question would a 6384 motor fit 🤔. BTW nice diy electric skateboard love the videos 👍

[@KAMiJUINs]

No. This 12in torque trucks can fit max 6380.

[@marsbase3729]

awesome build! 👍 😎 👍

[@KAMiJUINs]

Thank you for watching :)

[@danielgreen3884]

Those plastic dishes you used for the enclosure are going to break after a while if you ride on rough roads. Looks really good though

[@KAMiJUINs]

Thank you for your opinion :-) I think it is a weakness of DIY. (If i find better materials later, i want to change them.)

[@McClanahanAman]

I have a build similar with the same wheels but single drive. Those wheel are great for less than perfect surfaces especially if it has rocks which they kick to the side when you roll over them. Unfortunately, particularly with single drive, the traction sufferes due to the limited contact of the convex profile of the wheel on the ground. I can't imagine you ever reaping the benefits of 75 amps per motor with those wheels due to traction issues. I use 40 amps total which is more than enough for me and still have traction issues.

[@KAMiJUINs]

OK Thank you for your experience of opinion :-) In my case, this wheel, which has a small ground area, met with powerful torque on smooth roads, making speed wobble easy. I think, this setting is too much for ST e-board.

[@udsmall7306]

hmm I have the unpowered MBS dirtboard and I carve that thing deep and hard at 25mph on downhills and barely break loose on asphalt...maybe you just need to break them in a little? Builder Kaly/NYC builds Trampas and lathes the MBS dirt wheels flat for more contact...but that's what ABEC style wheels are for... 😕

[@KAMiJUINs]

@@udsmall7306 I saw the wheel shape.(sanded the surface) I'll give it a try. Thanks :)

[@Cretan-un6ul]

Do you have any build for 6384?

[@mikesmith7136]

will the 6380 fit on the atb hangars on your trampa?, I have found a third party that makes mounts to fit the atb hangar. I would like to go with 6380s.

[@KAMiJUINs]

Would be nice :)

[@DeliberateConfusion]

amazing build dude!

[@KAMiJUINs]

Thank you for watching :)

[@doglabdogtraining-gus.8873]

Great job

[@miguelmacedo935]

Hi where did you get those black spacers for the trucks so the front wheel doesn't move in the axle?

[@KAMiJUINs]

spacer included in the truck set and the thin ring shape of the spacers was added.

[@lassebak6909]

great vid.. doesn't the shock pads work better when between the board and truck instead of bolt and truck? just curious

[@KAMiJUINs]

Thank you for watching :) I've tried both, but it's similar.

[@TheMrFelin]

If I was doing it, I'd put the boxes somewhere on top where it wouldn't be in my feet. So I wouldn't hit them under the board in some stones or branches.

[@KAMiJUINs]

Thank you for watching :) That's a good way too.

[@tuckyew1]

love your videos, choice of music and your dog! may i ask, if you bought the bustin deck from their site?

[@KAMiJUINs]

Thank you so much :) I bought the deck from an offline skateboard shop

[@tuckyew1]

@@KAMiJUINs that's great that they sells it offline in your area! Love your videos. They are so detailed

[@noka7776]

Nice build bro, you should get a heat gun though.

[@KAMiJUINs]

Thank you for watching :)