60V Razor Ground Force Drift Kart | 2000W MY1020 Kit Install

[@JonnyDuzzit]

Hell yeah kabagis, lookin good! See you got some new tools as well 😎

[@PatOutdoors]

Trying to level up!

[@JonnyDuzzit]

@@PatOutdoors only way is up! 💪🏾

[@dioovaheaven3265]

@@PatOutdoors you got a link to the pedal? and maybe to a disc brake upgrade kit

[@MooseRidez]

Volt meter wires are backwards. I have a ytshort on it. They sometimes wire the leads backwards.

[@PatOutdoors]

Right, simple fix for the voltage meter. But the throttle itself failed after working a few min

[@rizole31]

Thats awesome i did similar to a ground force it's really fun. Even bought rubber tires for the rear for smoother speed runs

[@PatOutdoors]

Nice! Where did you get wheels with rubber tires? I’m having a hard time finding front wheels for more turn-I’m grip

[@rizole31]

They dont work too bad just pop out bearings and they match they keyway

[@rizole31]

Also just in case I believe the razor dune buggy wheels fit as well but air filled

[@PatOutdoors]

@@rizole31 I actually ordered a pair of front ones last week but they’re 10mm bearings instead of 8mm. I may just try to find a set of bearings to make it work

[@rizole31]

If you pop the bearings out of those they may work for rears for a bit smoother speed fun.

[@dschifftyyy]

I really enjoyed the part where you wrapped the chain around the shaft

[@PatOutdoors]

I really enjoyed the part where I owe you a drill bit set now because I refuse to return this set because it’s good luck

[@dschifftyyy]

@@PatOutdoors consider it a gift - as long as I get more shaft play

[@PatOutdoors]

I will do some private shaft play videos just for you 😂

[@DescartesRenegade]

That motor is going to be put to work with the small axle sprocket and 15t motor sprocket. I did this on my ground force drifter and even with a 40lb kid on it the vevor smoked. Also, when you charge, you'll need a 54V charger, not 60V. Those DeWalt batteries are only 20v MAX but they're really just 18V packs. So 18x3 = 54. Don't use a 60v charger that pushes to 67V, you're going to have a bad day.

[@PatOutdoors]

I wasn’t planning on charging it with a 60v charger.. I have 4 separate chargers for these type of batteries. Appreciate your input

[@cozyvibes6178]

How long do these batteries last for you when riding at mid speed? I assume its 60v 15Ah in total right?

[@nxdboi]

So sick. I've been trying to scoop up a Ground Force roller on the cheap to build up. I have a 1500W kit that I have laying around from an old MX350 project that I would love to put to use.

[@Thatwheeliekidalex]

You should buy and review the tuttio soliel 01

[@PatOutdoors]

@@Thatwheeliekidalex maybe if they send me one.. I would review it. I have too many bikes at the moment to justify buying it

[@thugtiny2679]

Your awesome man. I have lots of questions about some bikes I got. Where could I contact you at.

[@alanwilliams3909]

Awesome!

[@GIFT-Auto]

That's an amazing video. Will the motor and controller not burn out even under overvoltage?

[@PatOutdoors]

It’s only about a 20% overvolt and the batteries don’t put out enough amps to cause damage this motor. I’ve ran 72 volts @50 amps on these motors on my Razor MX650 and it’s still going strong for almost 2 years now

[@GIFT-Auto]

@@PatOutdoors Thank you for the great information

[@brandonbenjamin95]

Did you buy the 15 tooth sprocket separately? The chain from your links doesn’t fit the sprockets they gave me with the motor.

[@PatOutdoors]

Yes, the link for the sprocket I used is in the description also. 25h chain fits all razor bikes and karts

[@brandonbenjamin95]

Cant seem to find the link for the sprocket.

[@PatOutdoors]

@@brandonbenjamin95 Here are a few: www.ebay.com/itm/235370726227?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=uprsllegqkk&sssrc=4429486&ssuid=q9rYqNd_RGq&var=&widget_ver=artemis&media=COPY www.ebay.com/itm/404763959436?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=ykb8ekrbsf6&sssrc=4429486&ssuid=q9rYqNd_RGq&var=&widget_ver=artemis&media=COPY

[@PatOutdoors]

@@brandonbenjamin95 you could also go on eBay and type in “15T 25H sprocket”

[@zacgray9813]

I burned two controllers running 60v have you had any issues?

[@PatOutdoors]

Well true 60v battery may show 68ish volts so maybe that could burn out. I used dewalt 60v set up, which shows just above 60v, no issues yet. What exact battery are you using and what voltage does it show on the volt meter?

[@brandonbenjamin95]

What the link or name of the yellow wire connector panel your using? Aswell as what Chain did you buy?

[@PatOutdoors]

Junction Block (yellow): amzn.to/3KgdYui PGN Heavy duty 25H Chain: amzn.to/4bTjtuH

[@tfkafka]

nice!

[@Dlasky_999]

Tommorow I am upgrading mine to 36v

[@brennankemper5690]

Can I use original wires to connect everything or do I need to get some new ones?

[@PatOutdoors]

For which part?

[@brennankemper5690]

@@PatOutdoorsfor new batteries and charger

[@brennankemper5690]

Or should I just get a new charger and wires. And if so which ones?

[@breddy9282]

did this same exact build with a 15 tooth sprocket on the motor and a 52v battery got 40mph

[@PatOutdoors]

I just went out and it’s way too dangerous 😂 Did you have real tires on yours? I need a wheel/tire upgrade suggestion

[@breddy9282]

@@PatOutdoors Nah i havent put real tires on it yet, seems complicated as hell to put the rubber ones as the keys dont match up, if you wrap the wheels with some tape itll drift pretty nicely or a pvc pipe

[@mycoolsmah9018]

Can you give us the link of the sprocket? I can’t find the exact dimensions…

[@PatOutdoors]

For 13-Tooth Sprockets: www.ebay.com/itm/326053236653?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=q9rYqNd_RGq&sssrc=2380676&ssuid=q9rYqNd_RGq&widget_ver=artemis&media=COPY For 15-Tooth Sprockets: www.ebay.com/itm/326053235463?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=q9rYqNd_RGq&sssrc=2380676&ssuid=q9rYqNd_RGq&widget_ver=artemis&media=COPY Keep in mind this is ONLY for the MY1020 motor, does not fit the factory motor.

[@73notch]

This is rad! I am trying to buy replacement wheels but need the barcode ID to buy from Razor. Anyone have a barcode ID I can use from a drifter or Fury?

[@MooseRidez]

Hey broski. Just a word of advice. Put a small nut and bokt through the phase wires with a heat shrink then put the negative and positive in the bus bar/terminal block. This takes the melting/shorting risk out of the equation since these newer vevor motors no longer come with internal fans.

[@PatOutdoors]

Unfortunately no space for a heat sink on this one due to how close the seat is

[@MooseRidez]

@@PatOutdoors no no. Heat shrink on the bolts of the phase wires so they dont melt the vevor bus bar with the battery terminals. Keep it separate.

[@PatOutdoors]

@@MooseRidez ohh I got you. Well this is just a testing phase, I haven’t even cleaned up or tucked any of the wiring yet till I replace my throttle. I’ll keep that in mind when I’m wrapping things up

[@MooseRidez]

@@PatOutdoors yeah no doubt brother. I knew due to the size heat management gunna be a pain so keep the phase wires seperate from the battery wires will help keep sketchy things from happening

[@raymondbruggeman2556]

@@MooseRidezcan you explain this to me or post a link that would. I’m green to the electrical motorsports

[@sonnivega6739]

footpedal