A quick how-to on getting to the brakes on these British series International and CaseIH tractors.
Пікірлер: 106
@chriskelly67694 жыл бұрын
I am looking at a brake job to fix lost fluid and brake function on a 1466. This video nails it, very descriptive and video covers what I need to do. Thanks
@CanadianRedneck154 жыл бұрын
I am glad you found the video helpful, thanks for watching!
@tonycheyne90522 жыл бұрын
Excellent video. The only comment I would make is when refitting the brake piston, make up a couple of plates to use as a kind of press to make sure the piston goes in square and even. Real easy to cut the new 0-rings if this gets skewed on the way in.
@CanadianRedneck152 жыл бұрын
Excellent tip, thanks Tony and thanks for watching!
@deborahflint51645 жыл бұрын
Damm good video , now i know why my brake repair was expensive. Thanks alot.
@CanadianRedneck155 жыл бұрын
I am glad you enjoyed the video, thanks for watching!
@folinojohn37125 жыл бұрын
great video! Thanks for posting.
@CanadianRedneck155 жыл бұрын
I am glad you enjoyed the video, thanks for watching!
@TheMtnfox5 жыл бұрын
Great videos!👍
@CanadianRedneck155 жыл бұрын
I am glad you are enjoying the videos, thanks for watching!
@craigwilder64763 жыл бұрын
Follow the advice from your video, got the axle housings off all the O-rings replaced on both sides and everything put back together but we can't get the right brake to pump up. Any ideas or suggestions
@jimmymannion6874 Жыл бұрын
Fixed breaks 4230 thanks to your video 👍
@CanadianRedneck15 Жыл бұрын
I am glad you found the video helpful, thanks fpr watching!
@jamestwyman70205 жыл бұрын
great video thank you
@CanadianRedneck155 жыл бұрын
I am glad you enjoyed the video, thanks for watching!
@calumanderson56176 жыл бұрын
Thanks, we've got a 574 which hasn't been used since 2016 and I know those seals can fail, I don't know if you done a hand brake band video and (possibly the weakest design on theses 74series tractors but that's on our list to do, thanks alot 👍
@CanadianRedneck156 жыл бұрын
I ma glad you enjoyed the video. This series really were a great tractor, well built and comfortable to use, but like you say the hand brake was problematic. I don't have a video on replacing the hand brake band, I haven't had the misfortune of replacing one yet. :)
@berniestarzewski5482Ай бұрын
Makes me miss the days when the brakes were in their own pod and you didnt have to remove a bloody axel the service them!
@CanadianRedneck15Ай бұрын
Agreed! Thanks for watching!
@captndavie6 жыл бұрын
I have a 574 that needs parking brake rebuilt and my brakes go to the floor but will pump up and slide the tire. I'd like to see a video on parking brake rebuild and one on the brake master cylinders.
@CanadianRedneck156 жыл бұрын
If I have a parking brake repair come up I will certainly do a video, they are a pain to get to as it is in the differential case on the pinion shaft. If you can pump your brakes up it is likely the o-rings on the inside end of the axle housings that are leaking. I have a video on that here kzbin.info/www/bejne/r3y1h5aGfciUsKM . If you have any questions feel free to ask. Thanks for watching and good luck!
@lukeholmes27454 жыл бұрын
Wonder if you can help I have an ih885 prior to case merger an L cab model do the brakes have there own fluid resivour or do they draw hydraulic fluid off the back end?? And secondly when bleeding read somewhere to bleed brakes u need to clamp return lines ? Any help would be greatly appreciated 👍
@CanadianRedneck154 жыл бұрын
I'm not aware of any return lines and the brakes feed from the hydraulic system. You will need someone to pump the brakes while you open the bleed screws like any other brakes and I expect you will want the tractor running to be sure the system gets oil. Thanks for watching!
@Kt-ro2fm4 жыл бұрын
Great video Dave do you know if the case mx135 has a similar brake set up
@CanadianRedneck154 жыл бұрын
I am not sure but if you check in at partstore.caseih.com/us/index.html?csid=95b3fdc68521dc7bf5e844b7149d4b98&sl=EN¤cy= you will be able to see the parts break down. Thanks for watching!
@teamidris3 жыл бұрын
That looks like an international? Realises my David brown search has failed :o) But, I have done these and they are mad reliable. The O Ring can go between the rear casting and hydraulic housing where the bleed screw is, so change those very time to pop that housing. All the steel pipes chafe through, so rubber them up and clip em’ down. *Also, there is a flow divider valve for steering and it jams. Pull its bottom plug, put a bucket under there and blast it out on full revs. Then fine sand paper. It is genuinely a solid back end :D
@CanadianRedneck153 жыл бұрын
Excellent advice, thank you!
@sorinmoldovan51607 жыл бұрын
Nice! Can you make more videos with hidraulics ? I have problems with 3 point working with low speed .and is i stop the engine it get down by itself.
@CanadianRedneck157 жыл бұрын
What model tractor? When I have any hydraulic issues to address I will certainly make a video. Thanks for watching!
@kennethgavel67012 жыл бұрын
Many thanks for a great video. I've it watched several times, before attempting this repair on my 484. Everything went well, until I tried to install the large, inner "O" ring on the face of the bearing race component. There just isn't enough shoulder on the "O" ring recess to hold the "O" ring in place while installing the unit--it keeps slipping off the shoulder. Any advice on how to make it stay in place would be greatly appreciated.
@CanadianRedneck152 жыл бұрын
I expect there is a special tool to help start it, try cutting a large ice-cream tub or similar plastic to fit around the oring to get it started, then you could pull it out. Thanks for watching!
@kennethgavel67012 жыл бұрын
@@CanadianRedneck15 Thanks very much for replying. Good idea. Much appreciated.
@reececoro57754 жыл бұрын
Hi , i love your video's you make everything look so easy lol. I have a 585 international and the brakes are excellent ,but the hand brake doesn't work . the cable is good. where do i go from here please?
@CanadianRedneck154 жыл бұрын
The cable can be tightened in the lever to tighten the band around the drum. If adjusting the cable doesn't work you will have to replace the brake band. Thanks for watching!
@davidgoss34834 жыл бұрын
How do you change the low range ,reverse and slider gear on a international 484 thanks
@CanadianRedneck154 жыл бұрын
You have to split the tractor between the transmission and differential cases, everything will be visible then and you will see how to change them out. Thanks for watching!
@dannytheplumber73942 жыл бұрын
Good afternoon CR I have a International 624. The left side wheel locks up on slippery ground when I depress the brakes if you get a chance to make a suggestion of the problem , much appreciate your knowledge and experience.
@CanadianRedneck152 жыл бұрын
With the mechanical brakes it's hard to get them set even so that both wheels get equal braking, I expect that the left side is getting more braking pressure when you use both pedals. Thanks for watching!
@dannytheplumber73942 жыл бұрын
@@CanadianRedneck15 Thank you I will work from that.
@raymondosullivan19583 жыл бұрын
Was thinking of upgrading my diff on ih 454 to s type fast diff. Is it easy take out old diff? Thanks
@CanadianRedneck153 жыл бұрын
It's not difficult, you have to take the axle housings, brakes and retainer plates to get the dif out. Thanks for watching!
@p.jdonnellan99086 жыл бұрын
Hi I have a international 885xl that keeps hoping out of gear I have adjusted to linkage and no good what do you think is wrong any help would be appreciated
@CanadianRedneck156 жыл бұрын
If the linkage is adjusted so that the gear is fully engaging the most likely problem is that the gear is worn so the gear and syncronizer will need to be replaced. You can see the parts break-down at partstore.caseih.com . Good luck and thanks for watching!
@CanadianRedneck156 жыл бұрын
You are correct, split the tractor at the engine, then the transmission comes off of the rear case and, of course, the cab has to come off first just to add some fun to the job. It's not a terribly difficult job but it is a fairly large job. Let us know how you make out, good luck!
@johnromans7328 ай бұрын
I've inherited an 856. the brake pedal is hard. I can tell the left side has minor resistance. the parking lever won't go down at all. any suggestions
@CanadianRedneck158 ай бұрын
I haven't worked on a 856 so I'm not sure but if i'm not mistaken they are mechanical brakes. The actuators are likely rusted and seized up. I think they should be similar to the following video. kzbin.info/www/bejne/baenmKVjbrakrbs
@ellacarr68284 жыл бұрын
Hi Dave I enjoy your Videos, I have a IH884 with a ZF all wheel I need the part number for that small half moon snap ring that holds the master break cylinder to the metal plate because I lost it where can I get one in the US it is not listed in parts diagram. Thank you
@CanadianRedneck154 жыл бұрын
If you can carefully get the clip off the other cylinder you can take it to a machine shop for comparison, I expect that would be the best bet. Thanks for watching!
@chrisdelk69243 жыл бұрын
I have a 574. Is this job possible to do with the rear end on the tractor?
@CanadianRedneck153 жыл бұрын
Yes absolutely, you only have to remove the rear axle housing. Thanks for watching!
@huveralvarez48334 жыл бұрын
Porque solo encontré un separador en el planetario de corona
@danielturner84633 жыл бұрын
I have got a case 5140 maximum would that be the same or habit different thanks
@CanadianRedneck153 жыл бұрын
The maxxums are a different series but I think the brakes would be similar. Thanks, for watching!
@cristicimpian26272 жыл бұрын
To change the brake orings i have to drain all the oil transmission ir not?tnx
@CanadianRedneck152 жыл бұрын
Yes, drain the transmission/rear end. Thanks for watching!
@berniehammell4813 жыл бұрын
What causes brakes to lock up on 885 ih tractor?
@CanadianRedneck153 жыл бұрын
I've never heard of that happening before, there would have to be some kind of oil pressure leaking into the brake system, possibly where the oil feeds the master cylinders? Another possibility would be broken bits of a brake disk piling up. Thanks for watching!
@user-bd5bb6gt4xАй бұрын
Hi can you tell me. The stubshafts wich is left and right. Got them mixed up. One is shorter
@CanadianRedneck15Ай бұрын
I'm not sure, check on the differential and see if one side goes in further. Thanks for watching!
@Josh-je2niАй бұрын
This would be relevent for an 844 right? Where is the park brake assembly and how does one service it? Mines worn right out. Also has no brake pressure anymore, leaking all the fluid out
@CanadianRedneck15Ай бұрын
I am not sure about the 844, they're a different series of tractor but they likely are similar. Thanks for watching!
@nickorango3 жыл бұрын
I have a issue with my 844xl rear end. I have had a noice from the left side on the rear end. Which ended up with a total look up the other day. I did manage to unlock it by reversing hard.. Now it´s a really noice and i have not driving any more. Without even taking it apart. What would your guess be. Brakes or planetary drive?
@CanadianRedneck153 жыл бұрын
Brakes, bearings, planetary, hard to say until you open it up. Thanks for watching!
@nickorango3 жыл бұрын
#kzbin.info/door/0r8_4oyMNEtsXuHbWgKRXA
@nickorango3 жыл бұрын
@@CanadianRedneck15 Ok. That was a quick answer. I actually bought a 956 rear end the yesterday. They to look a just little bit different. Not much. Would you know if i can use it for parts. Or maybe replace the complete rear end? Thanks for answering.
@CanadianRedneck153 жыл бұрын
@@nickorango I don't expect so, the 956 is US made, the 844 is German, completely different series.
@humbertoencarnacionguzmanu87184 ай бұрын
Buenas tardes yo ise todo lo q dice en el video y no me fena nada q puede ser la falla
@altmuligmannen30862 жыл бұрын
Anyone ever made a video on replacing the band for the parking brake on these tracors?
@CanadianRedneck152 жыл бұрын
I haven't seen one but that doesn't mean there isn't one. I do know they're a PITA to do. Thanks for watching!
@fazeel12394 жыл бұрын
Hello can you please tell how to service Universal tractor brake.
@CanadianRedneck154 жыл бұрын
I am sorry I don't have any Universals to show. Thanks for watching!
@volkerreusswig43578 ай бұрын
Thank's fromm Germany 👍
@CanadianRedneck158 ай бұрын
I am glad you enjoyed the video, thanks for watching!
@matthewseipel4929 Жыл бұрын
I keep having to bleed brakes on my 574 more and more often. Brakes work great for a short amount of time. Is that a symptom of these o-rings failing?
@CanadianRedneck15 Жыл бұрын
Yes, that is a good indicator that the o-rings are bad. Thanks for watching!
@matthewseipel4929 Жыл бұрын
@@CanadianRedneck15 hey man, thanks so much for the videos. More people need to document stuff like this so we can keep them running!
@CanadianRedneck15 Жыл бұрын
@@matthewseipel4929 I am glad you enjoy the videos, thanks for watching!
@adriancarballo17503 жыл бұрын
Hola buen dia. Tengo un tractor internacional 784 . Y quiero aumentar la precion hidráulico. Me podría desir cual es la valbula de alivio y como ajustarla .gracias
@CanadianRedneck153 жыл бұрын
I don;t think there is any way to adjust the relief valve. If your pressure is low it's most likely the hydraulic pump that is causing the trouble> Thanks for watching!
@mikekehoe5065 Жыл бұрын
I need brake parts from this application. Piston and disc next to piston. Upstate ny
@CanadianRedneck15 Жыл бұрын
Send me an email, sales@chowntractorparts.com
@huveralvarez48334 жыл бұрын
Hola tengo tractor oh case 585 he encontrado partículas de bronce en transmisión específicamente debajo del diferencial he desarmado el diferencial y solo encontré un separador de planetario cuadrado mi pregunta solo lleva ese separador ? El separador no hay y la base donde hacienda el otro planetario está medio rayado ?cuántos separadores lleva 1 o 2
@huveralvarez48334 жыл бұрын
Y los satélites q son 4 llevan también separadores de bronce?
@CanadianRedneck154 жыл бұрын
There may be some brass washers in the differential carriers but the main source of brass would be the synchronisers in the speed transmission. Thanks for watching!
@huveralvarez48334 жыл бұрын
Hello quiero saber cuántos separadores lleva el sistema planetario y satélites de corona 585
@CanadianRedneck154 жыл бұрын
I don't know, you can look up the parts book at CaseIH.com
@JanYi20236 жыл бұрын
Thanks
@CanadianRedneck156 жыл бұрын
I am glad you enjoyed the video, thanks for watching!
@garethifan10344 жыл бұрын
Ohh..I thought this tutorial was for a Zetor..
@CarlosGarcia-gk6bf3 жыл бұрын
donde puedo conseguir un kit completo de freno para un internacional 80 en México
@CanadianRedneck153 жыл бұрын
I am not familiar with a model 80 but I would suggest a CaseIH dealer. Thanks for watching!
@CarlosGarcia-gk6bf3 жыл бұрын
@@CanadianRedneck15 donde puedo conseguir un distribuidor cacelH en mexico?
@CanadianRedneck153 жыл бұрын
@@CarlosGarcia-gk6bf I don't know, but I expect that Google would be able to help you there.
@sorinmoldovan51607 жыл бұрын
985 xl 4.4 l turbo ..it has more problems ,with clutch cilinders barake cilinders and hidraulic😖
@CanadianRedneck157 жыл бұрын
I am not very familiar with the David Brown hydraulic system, but it sounds like the cylinder leaking by or a valve not properly sealing.
@CanadianRedneck157 жыл бұрын
Sorry for the confusion, that sounds to me like it would be the "unloading valve".
@CanadianRedneck157 жыл бұрын
Yeah there's a bunch of valves on those tractors scattered around all over the back end and cabs make it more of a chore for sure!
@tientranxecay73534 жыл бұрын
Nói tiếng Việt được k vậy cho mình hiểu với
@CanadianRedneck154 жыл бұрын
Go ahead, I use google translate.
@TheMonopodi784 жыл бұрын
Piston has to be pushed equally in or it will cut the O-ring of the bearing retainer. I did it twice.