80cc Schwinn Stingray Retro 20 inch Cruiser Motorized Bike

www.southerncustomcc.com
Please Like and Subscribe
Here is the 60’s classic remake of the Schwinn Stingray 20 inch. Was lucky enough to get a few... hopefully you were too! Happy building.

[@hakanyildiz9602]

There is a sense and a manner in which this bike is more attractive than a Harley.

[@rickc2222]

the motor looks like it belongs there...wow nice.

[@ms-fl7jj]

I always wanted this bike when I was a kid!

[@Jenkyclip]

Please please please do more videos on this bike

[@arlenes.4590]

Much easier to add a 500watt 20" front hub, add a thumb throttle and brakes on front wheel like you did. Then under seat flying rack 36 volt 12ah battery and controller wiring and you got an E-ray. This can be done in an hour.

[@SouthernCustomCC]

You just gave me a great idea! Stay tuned in the near future for almost exactly what you described! I’ll shoot creds your way, too! 😎👍

[@arlenes.4590]

@@SouthernCustomCC checked many 1,ooo watt motor kits, much faster building an e ray, beware the torque on the dropuns. I would go with a 350 watt. Just searched and somebody just made a stingray with a 1000 watt front hub kit. Exactly as i mentioned. It looks very kewl

[@mpschunks]

@@arlenes.4590 found it here kzbin.info/www/bejne/ennRmqRjpJajjbc

[@maxhenry9724]

Not going to sound as cool.

[@Jenkyclip]

Do you think it would be possible to put a electric front wheel hub with the battery with this same build so it could be a hybrid stingray!?

[@lewisamberg4640]

I love it ! Memories with an update 🥰💯👍🔥🔥🔥

[@traviswartooth]

im trying to do this exact thing with my lowrider. its a tight fit on that frame but looks awesome.

[@jimmyv1233]

I built one like that but I cut the exhaust pipe and ran flex exhaust pipe to a minibike expansion chamber. With the smaller drive sprocket it did 35 mph all day!

[@jeromecabral192]

Nice build

[@garyquail2347]

I like the way that's all put together it looks like there was hardly any modifications whatsoever I bet that must be fun to ride something that I've always wanted to do to a Schwinn Stingray.

[@SouthernCustomCC]

Thank you, and thank you for watching!

[@alexkeena5665]

I did this to a 72 stingray junior frame a few years ago as a pit bike

[@JorgeRodriguez-ei2gi]

Great built on #20 stingray, could you make a step by step, motorized, on your built, thanks joe,

[@dekem7137]

Awesome as usual Mark! That retro style is so sweet.

[@SouthernCustomCC]

Thanks! Love the support and thanks for watching 👍

[@bobstaples7147]

I love it, How fun. Got a cool 1969 for sale, maybe I should do an up grade.

[@firedemon2166]

1969 schwinn stingrays are better stock

[@TheJoeMad]

That’s a beautiful bike.....Excellent job ... Do you folks provide a parts list for this build? .. Thank you.

[@SouthernCustomCC]

There is not much else you will need besides the bike and engine kit. You'll need an offset intake, 6” 17-18mm gas rated tube, and a shim (could be rubber or a pipe with he same diameter) for Tue rear mounting bracket. Then if you want a front brake, just pick one up on eBay for like $10. Everything else comes with the kit. I hope that helps! The is for watching, and hit me up if you have more questions. 😎👍

[@briansinclair5890]

Go into the grass trimmer section and get a 4 mm brigs and statton filter, they are shorter profile and will work. I had this issue on my fatmoto frame with built in gas tank.

[@SouthernCustomCC]

Awesome! I'll check that out today. I'd rather have one then not have one, but he stock filter wouldn't allow flow no matter how I set it up. Thanks for the input and being a part of the community!

[@gta5grindzxb145]

Love to have that bike!

[@myrandomstuffchannel3390]

You can get them for 125 on walmart.com

[@JorgeRodriguez-ei2gi]

Great build, could you share with us a tutorial built of this schiwn #20, or a step by step, process, thanks, southern, customs, say hello joe, from panama.

[@doylecase2922]

I've been building my own using bratz lowrider bikes with 20 inch huffy cranbrook rims and tins, and 80cc engine... not sure how to add pics to comments tho...

[@xjeepmanx]

Nice build.....subbed and smashed 👌

[@pheenix42]

FLAWLESS VICTORY. 😎

[@thomaswade9689]

Extreamly cool ! Beautiful job!

[@JayDee-eu7hr]

Looks like a wheelie machine!

[@JayDee-eu7hr]

running no filter lol just finished my cruiser bike they are so fun.

[@SouthernCustomCC]

With a 44t sprcket...wheelies are absolutely possible...with the 36t you can get some front tire lift action for sure--especially if you bigger like me and there is a lot of weight on the back.

[@GOOFYxNEWFIE]

Looks so cool awesome build

[@thomastrout9997]

I'll take 2, please.

[@slothzombi307]

Very cool. I'm wondering how the orange twist grips work. Wouldn't they be too tight to spin?

[@randomthoughts1001]

Absolutely awesome. 🙂

[@scotthansford3657]

subbed, can you do a how to for one of these style bikes

[@Saddletramp1200]

Your exhaust pipe is loose. Great looking bike.

[@octaviob5950]

This is magic, love it!

[@LouWeZee.]

I got a green one. I didn't know they were limited.

[@gregs.7963]

These bikes are "in line" items. They will continuously be restocked. ... Not limited editions.

[@Konstantinosmo]

I like the colour. Nice final result. Do you know if a 100cc 2stroke motor will fit at this frame?

[@SouthernCustomCC]

Thanks for watching! The 100 WILL NOT fit on this bike. The Monkey Fist engine sits best in this bike with a frame shim. Best of luck and happy building 😁

[@Konstantinosmo]

Thank you my friend, keep motorizing....

[@thomasmoje5926]

Very cool. Love the frame color. Very nice job on the motor installation. I snagged a 2020 reissue Sting Ray (blue/silver with the late 1970's style chain guard and white sparkle/blue 'S' logo and racing stripe seat) and would like to dress it up a bit. Where did you get the retro-style chrome bullet headlight?

[@Robert-hf5xr]

Wheelie machine huh

[@jermainesimmoms2379]

I like that is nice buddy

[@danewilson7812]

Badass

[@diatonicdoug6525]

Can the original carb mounting be used?

[@dansmith3378]

Where can I buy one already build like that

[@miguelpatino4041]

I did this like a year ago to same bike but a pink one it was dangerous honestly especially if you lean back to far very deadly

[@GratefulEd907]

Does the carb out on the side get in the way peddling

[@goodhustlemotorwerks9024]

Nothing wrong with an elongated intake more volume equals more horsepower

[@civilsocietyprivateinteres1711]

Sweet 👍 I got an original startfire 66cc from 2009 on a 26" cruiser im restoring, do you think a generic banana seat kit and sissy bar would fit that ? Or I would need to find one made for 26" bikes ? Thanks

[@SouthernCustomCC]

Awesome deal! Would love to see pics when done. I'd recommend staying with he 26” banana seat. They sell them on gasbike.net and bikeberry.com. Might look a little off if it's not the right ratio. Happy building!

[@1eyedwilli3]

I have thin blue, the 1980 schwinn stingray remake.

[@user-yz8oy1bb3n]

Пишите и говорите по русски

[@1eyedwilli3]

@@user-yz8oy1bb3n мне нравятся черепахи

[@fnafandstuff2x_x917]

The main difference from the real ogs is the pettels

[@joshbarrigada]

oh man i want to do this build so bad, suscribed,! when are you guys gonna have more engines for sale?!

[@SouthernCustomCC]

Thanks for watching! We have the Zeda 80 triple 40’s in stock now, but the yd100 will be back in next week. Take care.

[@b-ill2195]

Badass I would like to do something similar but with a 26 inch nice tho 80cc?

[@b-ill2195]

Looks Great

[@race-all]

Just wondering why you didn't paint the gas tank. Also does it have the two speed kick back rear hub? I wondered how that hub would work with an engine. I've been wanting to do a bike with one of those hubs.

[@SouthernCustomCC]

: I had to d the same, Nick, when I used a nexus 3 speed as well. I purchased--i believe--a 1-1/2” steel circle bit and drill pressed it to fit around the hub. This particular bike does not have gears...it is just a single speed cruiser. Thanks for commenting! Happy riding

[@bikerjon8934]

Paint the damn gas tank

[@jermainesimmoms2379]

I got a purple bike like that im about to put a 50cc on it

[@butchgarner3911]

Would you explain the safety reasons for no front fender? Please. Thanks! Great video and awesome bike!

[@SouthernCustomCC]

Vibrations and thin metal. If the fenders are not closely watched and tightness is not maintained, the mounting bracket of the fender can fail....which means the part that is attached to your fender that holds it secure to the bike is broken. Which then means the fender is not supported up. It then falls onto a rubber tire going 35mph+. The fender gets sucked in toward the fork at that speed. The Fender can then get stuck in the fork bring you and the bike to an immediate stop. If you are not prepared... Over the bars you go! The rear fenders are sometimes more reliable because of side mounting brackets, too. But not always! Safer to run without them IMO. Happy riding.

[@butchgarner3911]

@@SouthernCustomCC ah, ok. That makes total sense. Tomorrow I will be removing my rear fender as it shakes and rattles like crazy but, I had not thought it all the way thru. Thank you!

[@b-shishiner8189]

I have a Mogomie? 20inch. How much for this motor?

[@JorgeRodriguez-ei2gi]

Great video on schiwn rims #20 if you due to make a video on boys 24 inch rims motorize bike would be great tbhanks great job, show how you instal the schin motor, step by step, thanks, loe

[@SouthernCustomCC]

If I ever get my hands on one, I'll be sure to do just that! Thanks for watching!

[@brandoncortes5996]

This is sooo cool; great work! I’m so excited. I’m going to be doing the same build on the exact same bike when my kit comes in the mail next week and I was so glad to find this video that I can refer back to as I put it all together. I was hoping you could maybe give me a way to contact you in case of any questions? One of which being why you opted for no front fender? (Sorry if that’s a dumb question but I’m new to modifying bicycles so I’m a bit clueless right now other than the few things my stepfather has told me since he tinkers/buys&sells old bikes.) Thanks and merry Christmas!

[@richardmacdaniel4479]

The bike comes from the factory with no front fender

[@brandoncortes5996]

@@richardmacdaniel4479 I didn’t realize that at first because my bike was still in the box when I had commented but I’ve now got it all together and running strong 🤝

[@brucelynch2203]

@@brandoncortes5996 what kit did you use?

[@glennjrbeck]

Do you no Where i cani get that 80cc single jug from thanks

[@SouthernCustomCC]

Right now, nobody has this engine for a decent price. Everyone is a price gouging butt-head at the moment and prices are 200% where they should be. Reach back out to me in another month or so and I can help you get your hands on one! Thanks for watching.

[@glennjrbeck]

@@SouthernCustomCC alright thanks for the reply I'll check back later on

[@markrichardsonrichardson1793]

Any luck with those single jugs?

[@glennjrbeck]

I'm still waiting

[@waynehardy6186]

Southern Customs CC how can I get one of these have been looking for years for one

[@SouthernCustomCC]

If your local I have them. Otherwise, keep checking Walmart website for the bike and buy an engine kit from me. Then give yourself an afternoon to build it! Thanks for watching.

[@jetknight7562]

What would it cost to build one like yours..

[@becky7637]

Awesome

[@alfa7108]

Nice. I subbed

[@ernieaguilera7365]

How is it when you ride without the motor on? Does it make noise when just peddling?

[@hotrod40hec1]

Im having problems with the exhaust do I have to cut it if so how much

[@niteramscreations8653]

Looks like the Orange Krate edition

[@firedemon2166]

Except it’s not a krate model and this one is only 125 from Walmart for some less quality parts, which is cheaper than the amazon ones and the krate one by more than $400

[@850are2]

Cant believe that manifold works. I cant get any offsett intake to work

[@SouthernCustomCC]

Do you use the cut-off allan wrench to secure the right bolt in tight enough? Because if that bolt by the ’bent’ side isn't secure enough, you could have an air leak. You can purchase an extra 5mm (I believe off the top of my head) allan wrench and cut of enough of the tip with a hacksaw or grinder. Then you can fit it in and tighten the bolt properly. Just a suggestion, but maybe you already have done that.

[@850are2]

Southern Custom CC i gave up and changed it back. Runs great

[@larryshaver3568]

is the light battery powered?

[@JoseRodriguez-kh7ju]

Do u think an 100c will fit ?

[@TheLouisamite]

It would've gotten a like by me if you would've used a66cc engine instead of that 49cc,an you had to have seen that muffler shaking like that, and black hose instead of blue,,,on that color frame that blue just jumps out

[@lucasdaily475]

Tutorial?

[@RJDCR]

kool

[@lindsay8794]

Where did you buy the front head light and how is it powered? Thanks Max.

[@SouthernCustomCC]

You can grab these on eBay. Retro bike light. Powdered by 3 AAA batteries 👍. Thanks for watching.

[@johnmccauley4533]

Mine doesnt like to idle like that. Idk why. It just likes to run while in motion. And when I use the clutch the engine starts running really fast, Made me pop a wheelie and scared the hell out of me.

[@robinrobinrs300]

you have to adjust the idle screw

[@chevytruckk3479]

Your slide in your carb isn’t in the right position causing the needle to be up. I did same thing on mine.

[@syhanson9723]

I had the same issue and it wasn't my carburettor, no matter what I did to adjust that tick over screw it ran away on choke and sometimes ran away on revs when I pressed the clutch in other times it would just stall out. I checked everywhere for an air leak and this also sounds like you issue . I changed gaskets to find the base gasket had broken in half allowing an air leak .. so I rebuilt it with all fresh gaskets . I'm running a hp carburettor, if you are then that won't work with a standard length throttle cable , will need to do some modifications to the top of your carb, it's easy if you need to do it let me know

[@syhanson9723]

@RUCKUSSAY AUDEO RODEO there's not a screw cap on top of my carb I'm running a HP carburettor.. it was an air leak at the base gasket.. I brought a complete new gasket set.. stripped it down and replaced them all .. it now runs fine.. :)

[@johnmccauley4533]

Well shit... I'm not looking forward to taking the engine off and checking all this. I have a lowrider bicycle and there very little room for the engine and carb. I think I need a new carb intake manifold. Mines all ghetto looking with copper pipes and jb welded together. I knew it was a dumb idea.

[@Jenkyclip]

is it possible to sell this as a conversion kit, willing to pay! 💰

[@bigdingus6196]

where can I buy this engine

[@toosunakabooma1213]

Is that crank clearing the cases in stock configuration?

[@SouthernCustomCC]

Yes, it clears by a little more than 3/4”.

[@poorcomboz3577]

How did you put a different grip on the throttle?

[@SouthernCustomCC]

Thanks for watching! I cut the crappy black one off with a razor blaze, the used a lot of wd40 inside the new grip and on the throttle. Then shoved it on. Hope this helps!

[@roryboru3802]

So that's really a zeda 80cc in there?

[@kenneth2512]

I think it's a Motoos engine with a single piece cylinder.

[@wabisabiali5566]

how did you mount the motor to the frame? I'm trying to do the same thing to my stingray

[@SouthernCustomCC]

Thanks for watching. Because the frame diameter is smaller, I used the front engine mount adaptor and a shim in the rear. You can use a rubber wrap or a metal pipe spliced in half that is the same diameter as the frame on the backside of the motor. Hope that helps! Happy building

[@wabisabiali5566]

@@SouthernCustomCC thank you! I was also wondering if you think its possible to mount a rear bike rack onto the stingray?

[@jcx5659]

The exhaust looks loose. Wobbling all over.

[@SouthernCustomCC]

Good eye... Not loose...jist the camera catches the vibrations. It's typical, but not loose 😎

[@Rbvchip]

Can you put a CNC sprocket on this bike

[@SouthernCustomCC]

Yes, you can put a CNC sprocket on it. Just make sure you order the right size for your hub. You'd want maybe a 32-34 sprocket because with a 44 you may be popping wheelies! Have fun 😎👍

[@Rbvchip]

Southern Custom CC thank you I got a 36

[@coreylopina23]

Your exhaust is loose af

[@123hoodnig]

Mufflers loose

[@victorsconfidential767]

That’s not a 80cc that’s like a 49

[@robspear03]

Its a shame it has to be one of those Happy Timme 66cc junk engines. Otherwise, neat project.

[@rcDoom]

I got a better idea... Just buy a Scooter

[@adamsicotte1151]

What a gay looking bike,,,,,,

[@SouthernCustomCC]

🤦‍♂️ SMH

[@syhanson9723]

Not everyone's cup of tea mate but no need to be like that. What bike do you have Adam Sicotte?