A transmission harness for Coyote Swap's PCP-1117

[@FoxcastMedia]

Love it! Keep cranking out those bad ass parts!

[@PowerByTheHourPerformance]

Thank you Caleb!

[@arturoholguin1723]

Hello, how are you? I have a fault in my truck, I have a 2013 lincoln mark lt and it just started to make a fault, I put it in drive and when starting it goes to second and then it is positioned in fifth gear, I want to think which is the electronic harness that has a fault, could you advise me what I can do about it? Greetings, excellent video !!

[@PowerByTheHourPerformance]

Arturo, sounds like a transmission issue. You would want to check for codes related to the fault and then diagnose it. If it is not a circuit code I think you will find that the transmission has a mechanical issue.

[@joelubner3879]

I am using your Gen1 and 6R80 harness for my Coyote swap in my coupe. I have Dakota Digital cluster with BIM-01-2 do I need to do anything with speedometer wires?

[@PowerByTheHourPerformance]

You should be getting speed signal from the bim module so no. You just leave those wires alone.

[@joelubner3879]

@@PowerByTheHourPerformance Great Thanks what about the tach and oil pressure wires?

[@PowerByTheHourPerformance]

Tach should also be in the can bus stream, for oil pressure, use the supplied sensor with your gauge pack and wire it direct to the control box. Coyote pcm does not meter oil pressure.

[@joelubner3879]

@@PowerByTheHourPerformance Thanks

[@davidmendez9851]

Ei I got a mustang 2014 and i want to do coyote swap is there any way i ken send the pcm to take anty teff out i got the padle and every thing answer please let my now what do i need to do

[@PowerByTheHourPerformance]

We can do this with any 11-14 mustang GT pcm. It is $250. we omit the pats system and leave the rest stock.

[@alh5273]

I have a 2006 GT which I’m swapping. I have the PCM and engine harness from a 14 along with your body harness. Can I use this harness with my 3650? And also do I need the 14 fuse box for the body harness etc to work? Thanks!

[@andresg203ag]

Does this work on a gen 1 coyote and FRPP control pack am doing a coyote swap on a fox body but am thinking of doing auto-trans...

[@PowerByTheHourPerformance]

It would not work with gen 1 frpp control pack since it is only available for manual trans from ford. You will need a different body harness like our pcp-1116 to be able to run a 6r80. And then this harness will work.

[@andresg203ag]

@@PowerByTheHourPerformance ok thanks am going to look into it

[@randomvideos8537]

Badass harness but not even 299 anymore now it’s 399 🤯🤯🤯

[@bioni007]

Would this Harness work for me if I’m doing an auto swap on my 2015 mustang 5.0

[@PowerByTheHourPerformance]

It would not. This is for gen 1 only and mainly for coyote swap projects.

[@bioni007]

Power By The Hour Performance thanks you Helps me a lot One more question do you guys have any info on an auto swap or do I just look up on Forums

[@PowerByTheHourPerformance]

We do not have a write up but plan to do one or a video soon.

[@MRHMOTORSPORTS]

Hi can you make a new videos in the future next week or later?? it's all about Features and Benefits etc you name it, POWER BY THE HOUR GEN3 BODY AND TRANSMISSION HARNESS FOR COYOTE SWAP PCP-1186 .Thank you

[@MRHMOTORSPORTS]

i'm gonna swap my 20 mustang ecoboost with RPG GEN 3 Coyote long block level 3 ( fully built internal i-beam conrod etc). and i'd use your harness i hope it works ! do you have any advice for me? this is my first project cars in 24 years old hehe

[@davidmendez9851]

Any body nows how to fix the pcm for coyote swap let my now please

[@PowerByTheHourPerformance]

what do you mean by fix?

[@Angry-Little-Fish]

Badass harness but it’s not 399 anymore now it’s 500 😭😭😭