Acura TL Rear Brake pads and rotor replacement

thank you for watching!!!!!
If this video was helpful to you and if you would like to place a donation, here is my Venmo and PayPal information. Or I would really appreciate it if you could share my KZbin channel on your social media. Links will be on the bottom.
#acuratl #brakepads #jabothemechanic
venmo.com/code?user_id=265066...
www.paypal.me/urbanautomotive

[@alanlehouillier8494]

Great video. Thanks

[@tiffanyh5929]

You did a job simple easy peasy

[@BillMcGirr]

Good video. Solid information here. 👍💪🥃

[@kirkbaker7239]

Thank you for your knowledge sir.

[@aangeloj79]

Brother u got a new subscriber here !!

[@RydellNez]

Ok thank you so much I'm gonna subscribe

[@JaboTheMechanic]

Thank you for your support 🙏

[@joemama-hc4gl]

I will be replacing the rear brake pads alone soon on my tl 01. The original rotor will stay, will that be ok? Also im using Hawk performance ceramic pads. Is it ok to use ceramic on OEM rear rotors? Or do i meed a different material?

[@shantor100]

Watch that brake line. saying if it falls is no big deal. Not good to stress the brake lines. I'm sure you know that though

[@flighboy83]

I stripped the screw before I could get the rotor off...any tips to remove

[@m.b.2499]

do you not replace the middle clip? my kit came with one

[@Ya_Boiye]

How important is it to get the boot back inside the pad mount if it comes out when greasing guide pins, I cannot for the life of me get them back inside

[@sammyv9167]

You probably got them mixed up, when lubing, do one at a time

[@ajaxgomlez]

I've seen a lot of brake pad replacement videos for both front and back and discovered the fronts are Brembo brakes for 6SP manual. Are the rear brakes the same for both transmissions or different for manual? Great video btw

[@litarea]

I believe rears are the same for both

[@kfm908]

why would they be different? @@litarea

[@litarea]

I don't know, I didn't ask the question.@@kfm908

[@kfm908]

if those 12 mil bolts are stuck or rounded off all you have to do is loosen the 17 mil nuts behind them by the rubber seal

[@gvebtb]

Can you not just remove the entire caliper bracket first and hang the set? Trying tomorrow, will follow up.

[@RydellNez]

Hey so I did the same process and for some reason it smells like the pads are constantly touching not by much but getting a little burnt smell... any suggestions?

[@JaboTheMechanic]

Your breaking in the brakes normal smell

[@RydellNez]

Ok thank you how long will it smell like that

[@JaboTheMechanic]

@RydellNez depends on how aggressively you stop. Speed up to 60mph go to a complete stop repeat two more times. Could take up to 50miles.

[@ethancox2418]

What happens if you dont compressed the calipers

[@theshadowspartan4047]

Did u find out

[@johnmoorhouse5764]

Then you won't be able to get the caliper over the new, thicker brake pads

[@djbromann88]

Tell me do you have to change the rotors every time you need brake pads

[@johnmoorhouse5764]

No

[@johnmoorhouse5764]

No

[@Takoeye2008]

What is that rubber plug on the rotor for?

[@Takoeye2008]

And thank you for this video. You make it look very easy.

[@JaboTheMechanic]

It's so you can adjust the brake shoes

[@Takoeye2008]

That's what I thought. Thank you!

[@nacocarnal]

Non of this dmsess change the caliper hardware, that causes noise

[@matyrobloxtoonsandanimatio6107]

Hi

[@JaboTheMechanic]

Hi