From milwaukee to Makita. Why I changed tool platforms

[@sueneilson896]

Can add this to the discussion. All my 10yo Makita tools were caught in an unexpected weather event recently and were completely submerged in their plastic tubs for about 48 hours until rescued. I was devastated, and prepared to replace everything, but to my utter amazement, all the tools, batteries and eventually chargers dried out and began working again. 9 months later and all are fine and working as well as ever. I did buy a couple of new batteries and a charger just as a offering to the Makita Gods for their beneficence. Changing brands would be sacrilege for me after all that!

[@realpatriot5896]

Interesting that you brought this up. I dropped my oldest Bosch cordless drill in a creek when I read building a bridge over it. It went completely under water and I had to go get wet to get it out. I jumped right in after it. To my amazement it just kept working. At that point it was already so old I can't even remember when I bought it. Probably was at least 7 years old at that point. It is still going strong and I have only noticed a slight decrease in battery life. I ran a drill pump with it not long ago and it did great. It came with two of the 1.5 ah batteries and a charger. I still like Makita the best though I am very fond of Bosch as well. Just wish they made more tools. Bosch is great quality for the price you can get them at! Especially for the CPO refurbished ones.

[@tracklizard4018]

Brushless tools are almost guaranteed to work after being wet. As long as you let them dry before use.

[@FishBaitBlue]

Keep a close eye on those batteries though. Probably not a bad idea to store them somewhere they won’t pose a fire hazard.

[@Galaxywolf712]

pretty much every electric tool can survive that the batteries are protected from water and shorts because of water its only the battery that gets killed the tool always survives since it gets provided the power by the battery but alot of the times the battery survives

[@sueneilson896]

@@FishBaitBlue … fair point. Though 18 mths later all still going strong.🤞🤞🤞

[@TruthSpeaker1001]

I have all Milwaukee Fuel and am totally satisfied with their performance and reliability.

[@PartTimeYooper]

I love you still have your original Makita drills. I still have mine from 13 years ago and both still work, even though the drill has been smoking more than a few times from mixing drywall mud. I also agree that Makita is more Carpenter focused than Milwaukee

[@patrickm1533]

My Makita batteries are over 10 years old and are still running like new.

[@unSTEVOED]

I don’t understand why people go for battery tools that are stationary when set up ie. drop saws, rip saws etc. Fair enough if the sites don’t have power, but the majority of the time most building sites are powered.

[@AddictedtoTools]

Hey mate, I definitely understand what you’re saying but maybe it’s the sites and work you’re doing. On all the sites I’m on almost no one uses leads. They are painful to run through site safely and battery is just a lot easier. If it’s just for home in a shed then I totally agree.

[@brandonhoffman4712]

The milwaukee 18v 12ah has more capacity than the makita 40v 4ah. Lets talk battery facts. Manufacturers claiming 20 & 40v are legally lying to you. They are 18 and 36v. Secondly, capacity for batteries is measured in Watt-hours. Which is voltage x amp-hours (ah) So to normalize the comparison we must drop the makita to its actual 36v, then multiply that times 4 amp-hours for 144watt-hours. Then take the 18v battery times its own 12 amp-hours for 216watt-hours. As far as max tool power, thats based off cell discharge capacity, marked as a C rating. (1c, 2c, 3c, etc) multiplied by the overall capacity of the battery pack. Since we just established that the milwuakee battery has more capacity, given similar C ratings (most likley), then the milwaukee battery can also supply more power to the tool. Higher volts mostly mean thinner wires on higher amp machines, thats about it.

[@High1QWealth]

Milwaukee is far superior quality!

[@nathanc3189]

It’s funny how people get super polarised by tools like they do with politics. They are tools… every tool brand makes good tools nowadays, Makita, Milwaukee, dewalt, Bosch even ryobi! I personally have Makita and Milwaukee tools, both living harmoniously together in my packout storage. Both brands are excellent

[@AddictedtoTools]

100%. Couldn’t agree more. Many were confused when I used other brands, thinking I’m only a Milwaukee guy. I’m a good tool guy. They all have their pros and cons. It’s just east to get stuck on one platform because of batteries and chargers. I’m actually really excited to get more ryobi gear. Might make some leave the channel😂

[@nathanc3189]

@@AddictedtoTools id put money on there being more ryobi tools in most households because of Bunnings or home depot than there are Makita or Milwaukee tools. You’d probably increase your followers to the much larger home handiman diy crowd. Ryobi are owned by same parent company as Milwaukee, have you seen the ryobi 12v tools? M12 cousin.

[@Rockbottomsurf]

Get polarised by the fact you get locked into one brand once you’ve got their batteries.

[@nathanc3189]

@@Rockbottomsurf you arent locked into one brand, youre free to buy as many tools and batteries from as many manufacturers as you want! yeah its easier having all the same batteries but even milwaukee has 2 battery systems you can buy into on their platform. i have makita and milwaukee batteries and i have never paid for a battery they always come with the tools or are added bonuses when buying during sales. its no biggie

[@Rockbottomsurf]

@@nathanc3189 of course “ locked into one brand” isn’t necessarily true but owning a number of dual port chargers for my Makita batteries makes charging and carrying chargers more streamlined. Even if I were to go to a higher voltage platform I would stick to the Makita range as not only does it save me from having a number of different batteries and chargers but I find Makita rarely has a tool that bad that I wish I didn’t get it.

[@kiwdwks]

Makita has been by my side helping me do the work for 40 years. Great tools!

[@brandonhoffman4712]

Makita is one of the top brands. I love plenty of makita tools. I sadly recently retired my makita drills after feeling the power of a new milwaukee impact with 4 modes. But that 40v 4ah has less capacity and output capability than that 18v 12ah milwaukee battery. Facts. More volts doesn't mean more power with battery tools. Bigger batteries do, or better batteries do (on a cell level). A great for instance is that makitas own 18v 5.0ah battery and thier 40v 2.5ah battery both contain the exact same number and type of batteries, just wired differently. Also 20v and 40v type branding is legal lying. They are all 18 and 36v in actuality. I suspect eventually all the branding will swap to the 20, 40, 60 standard as the EU allowed it.

[@naciofan11]

This saw kzbin.infoUgkx84IcU5pbZd1Qrz8u4-YRLmJax7kdRi7B comes in handy in many ways. When I had a small (dead) tree fall I started the process of disposal by using this saw and cutting off the small branches. Then slowly work on the small trunk with undercutting and letting it fall down. With many trees on acres of land paying for a tree service can be expensive. It also is nice in that it can be used in hard to get areas like along my creek. It's also safer and quieter than a chainsaw. It obviously can't cut down massive trees but it does work fine for small ones or brush. And of course since I already own a Black

[@mikek5016]

Agree with the batteries 100%. Makita batteries have been bulletproof for me. I have 10-year-old batteries that just won't die.

[@amateurvegan2636]

Makita are the very worst imo!

[@mikek5016]

@Amateur Vegan you must use them underwater lol. I am not brand loyal. I currently have Dewalt, Makita, Milwaukee and a few Ryobi tools. Only batteries giving me trouble are Milwaukee. Seems to vary a lot depending on the specific model.

[@amateurvegan2636]

@@mikek5016 I’m in the uk, the makita batteries might be different because they’re the ones I’ve always had the most issues with and the only ones other then Bosch 12v I’ve ever killed completely. Never had any problems with dewalt

[@jeromebland8287]

​@@amateurvegan2636I'm in the USA Makita batteries have lasted me years beyond their warranty ! I still have Makita batteries from 5 years ago working fine

[@lkm55]

I’ve been in Makita for years because of the batteries and the chargers.

[@DaveDoesCarpentry]

I’ve always believed Milwaukee have the best tools for electrician and plumbers, but in terms of saws for carpentry it’s been between dewalt and makita (makitas 40V is the best for saws currently)

[@JoeC92]

The thing I find though as a sparky working for a company that provides all our power tools, you are right they have the most tools for us. But if I bought any of these tools myself I'd be pissed. I think so many are biased because they pay for them themselves and no way would the have bought something bad right? But seriously Milwaukee may make the most powerful tools but their tools are not reliable. Hospital build currently with 45+ guys on site in less than two years 4 of the hydraulic punch kits dead all were brand new. Countless bandsaws down And at least the gen 3 impacts and drills are terrible. They can power through plenty of stuff yes but then just completely shit the bed. When I was non union I provided my own tools and bought Makita. No regrets. Even my impact that's 12 years old now first brushless they offered, still going no issues. Even speaking with other trades whether it be the concrete formers, welders and iron workers or plumbers/fitters. All Union trades so none of us actually provide our own power tools all saying the same Milwaukee has gone so far down with reliability. They aren't meant for the hard consistent use that comes on big commercial and industrial jobs. Go figure the greenlee punch kit I now have at work that we went back to using is still going strong when it's 8 years old and the Milwaukee ones are dying every few months. Milwaukee may warranty them but it doesn't matter it's 2-3 weeks waiting for them to warranty and get them back to us that's 2-3 weeks of lost production because their $900 Punch kit that they advertise as professional grade can't stand up to doing 10 3" punches in a row without the pump giving up.

[@kevinr3263]

I agree dave

[@gorkyd7912]

@@JoeC92 Milwaukee used to make REALLY reliable tools and you can still find 15+ year-old impacts and power drills in use on job sites, but I think more recently they might be slipping. They grew into a lot of other areas. Like, I don't remember ever seeing Milwaukee gloves or pliers, when did they start making gloves? Great gloves too, and their lineman's pliers are arguably better than Klein for less $$, but meanwhile for power tools: I'll take the DeWalt chainsaw and Ryobi for everything else.

[@JoeC92]

@@gorkyd7912 100% agree. I've been with the same company for 10 years now and we never used to have the issues we have now and always been using Milwaukee. I'm yet to try the Milwaukee pliers but ditched Klein for knipex and never looked back

[@JoeC92]

@Adirondack Homestead that was me for Klein tools too. Got sick of having to constantly replace screw drivers and pliers because the tips round out so quick or pliers can't cut anymore. Switched to wiha drivers and knipex pliers and no issues again. I don't get how so many can look past the lost time from broken tools and not realize the loss. The company I work for is huge, and multi trade we have a Milwaukee rep dedicated just to our company and the service still takes 2+weeks. Too much lost time I wouldn't be surprised if they switch from Milwaukee soon. Same thing happened with the rental company for boom lifts etc. Lifts the break down and then they take a week or two to come service them while still trying to charge $3000 a week in rental fees. Stopped using them and switched to one of the others that at least comes when you call them.

[@jeffbailey4928]

When tools were corded you weren’t limited to “tool platforms”. For framers, each company was known for and by specific tool groups. Best wormdrive saw, Skill. Best Saw-Zaw, drills and hole-hog, Milwaukee. Best jigsaw, power-planner, and laminate router, Bosch. Best 12” compound miter box and 10”job-site table saw, DeWalt. Best 1/2” impact and 3 horse plunge-router, Makita. Best framing gun, Hitachi. Best to horse fuel tank compressor, Emglo. All the name-brands crossing over to cordless was a smart move because it locks you in to one brand and creates repeat business on expensive batteries. I’m really surprised Skill hasn’t come up with a cordless version because Makita’s 40 V cordless can go a whole day on a framing crew without having to swap out batteries.

[@randomrazr]

is a universal battery for all brands possible? XD

[@realpatriot5896]

I use Makita, Bosch, Metabo HTP and Kobalt. It depends on the type of tool you are talking about on many of them. However, there are great tools from some brands in the same categories as well. For instance, both Bosch and Makita make great cordless sliding compound miter saws. Kobalts 7 1/2 inch cordless compound miter saw is awesome as well for it's lightweight and easy portability on a folding portable stand like the Delta stand. I favor Makita tools as well but Bosch makes some great tools as well just not as many. Kobalts are pretty good but definitely not as durable as the others. Metabo HTP's cordless tools are good for the most part but very expensive and there cordless compound miter saw is not so great. However, Metabo HTP's cordless nailers are the best and you can find deals on them at times where you get free tools with them buy purchasing another one of their tools. You pretty much have to do a lot of research watching videos and reading reviews. I do not agree that one needs to be limited by a battery platform though. I have found you can get into any of them by for instance buying a starter kit and getting a free tool if you are patient and vigilant.

[@randomrazr]

no no no no on the internet u can only fanboy one brand, not muktiple@@realpatriot5896

[@wildechant3667]

There are adapters one can purchase to run Milwaukee batteries on Makita and dewalt, Makita on dewalt and Milwaukee and Bosch, dewalt on Makita and Milwaukee and etc.

[@reaperreaper5098]

@@wildechant3667You lose a ton of performance, some batteries can be killed if used with certain brands because some companies put the BMS in the tool while others put it in the battery, and some are just fire starters

[@Steve-vz3ud]

I have also had Makita tools.35 years as a finishing carpenter.18 volt and corded.soon will move on to 40 volt platform.Good review👍👍👍

[@brianf9619]

You have to do your own Research when getting into a Platform , Milwaukee Does NOT make all the best tools despite what their FanGirls say 😂 , they make a few great tools but the rest are basically Ryobi painted Red ..... 😂🤣😅

[@deanohit]

I'm a Makita fan due to the weight, ergonomics and reliability,I'm using gear all day and the Makita gear generally feels more comfortable in hand, less weight hanging on my belt and less downtime due to tool breakdowns. So far the only Makita tool to fail on me has been the gib screw driver

[@dickphan]

Right on deano.....makita is the lightest of them all and comfort for all day use is top scorer....all my Milwaukee sits in the draws ....always go for my makita gear first...

[@henryairconcepts2999]

Makita is super reliable and cheaper overall than milwaukee. My first Makita 18V battery 3ah bought in 2012 and still works. I have M12 tool range as well though

[@nouun]

Funny that you mention weight, one of my friends has a Makita drill and while I do agree that it does feel a bit nicer, the skin alone with no battery seems to weigh almost as much as my Milwaukee drill plus a 5Ah batter.

[@Greg-ds7nd]

With the option of battery adapters now I've decided to adapt what I think is best in category to use. I have Milwaukee most but I like makita circular saw due to the dust shoot. Milwaukee jigsaw is not very good chips and frays edges when I use down cut blades so I use a dewalt .

[@randomrazr]

is dewalt good or sucks?

[@antonmaxx]

Milwaukee makes good tools but their batteries are garbage. My Dewalt 4 ah batteries are still going strong after 15 years.

[@volvogt21]

The makita table saw is pretty average. I bought one and returned it. The larger dewalt version is far superior in design, features and construction.

[@maisummarceneiroumdemuitos8037]

Agree, I have a lot of makita tools but mitre saw is a DeWalt.

[@Mrm00se1337]

Same, team teal over here but picked up the DeWalt tablesaw as the fence on the Makita I looked at was terrible

[@frenchyroastify]

I'm heavy into Makita now and very happy with their tools. I'm off Festool now that my vac remote stopped working 4 months in and they say they don't warranty accessories.

[@Dani-it5sy]

Thanks for the heads up. I never give money to companies like that. Charging top dollar while giving as little as possible in return. I don't care if they are the last brand on earth. I'll improvise.

[@daveonezero6258]

Its dumb to stick to one brand. Also dumb to trash other brands or peple for their choices. It really doesn't make much of a difference. It just makes sense to stick to one brand for each type of battery. Like I have m12 tools I use for work. But I have 40v Ryobi for my house stuff.

[@guendavienny_]

I completely agree, I had the same problem with Milwaukee, most of their high output are weak, unreliable mostly the 12.0, and the circular saw 7 1/4 fails a lot, over a year I switched to Makita 40v and its amazing, the 40v Saw its the best and I haven't had any issue with the batteries, the charger charges fast and has dual fans its just amazing

[@scottphilips8514]

I’ve always been a Milwaukee fan, but I got to admit, they’re taking the piss with their pricing now. It’s so fucking expensive for shit that can be made for a fraction of what they charge .

[@ricardoantonio9824]

Own a bunch of Milwaukee power tools and batteries and never had a issue ever, except for thieves who love to steal Milwaukee tools

[@javantgarde]

My dad used Makita for 30+ years, never had a failure and they can take tons of abuse, I do prefer to buy my hand tools made in the USA though.

[@RR-ss1tj]

I use to be Anti-Makita for absolutely no reason other then that I used all Milwaukee. I tried my friends Makita because my Milwaukee died, and WOW!!!!!!! I sold all my Milwaukee gear and switched to Makita. I find Milwaukee to be like an old muscle car, and find Makita to be a refined super car. Makita doesn’t seem to be powerful, but that is because I use to associate power with tons of vibration. Makita has power, but made it run smooth and efficient without shaking my bits off like Milwaukee. I’m glad I can now finish a day of work and still feel my fingers 🤣😂🤣😂🤣

[@thorinbane]

This is important and rarely a factor for all these power videos. Ergonomics , esp for smaller hands/ less strength is important. You might be a bear in your youth, but as you get older all those repetitive strains matter.

[@f1reguy587]

What are you talking about. Fix your tools…

[@pb6839]

In the EU, Milwaukee is more expensive and when you need a tool, they’re always scarce. You have to shop around online vendors. It’s annoying. Makita is always a safe bet anywhere.

[@DaveDoesCarpentry]

Man I would have loved to see the 50k worth of tools your old company purchased

[@AddictedtoTools]

Yeah it was awesome. There was a lot of larger gear, torpedo lights, hammer drills, crimpers…. But still a lot of gear

[@steffendetrick]

As someone who owns a lot of Milwaukee tools, I will say everything you are saying is 100% correct. I have way too many Milwaukee tools to completely bail on the M18 platform, but there are a lot of tools that will be replaced with the XGT. I did buy the Milwaukee traksaw, which is a great tool. But no Bluetooth dust extraction. Sometimes I feel like Milwaukee is tone, deaf to what is going on around them. I like Milwaukee but I’m feeling frustrated with them as a Company right now.

[@nickmilone5996]

You know you have to be one of the laziest tradesman in the world when not being able to turn on your dust collector remotely is a problem that affects your work.

[@steffendetrick]

@@nickmilone5996 t’s not remotely it turns on automatically. And when you have a shop like I do with guys working in it that don’t always turn on the dust extraction it’s a helpful feature. Not everybody’s situation is your situation. And regardless of that fact, every other premium brand offers Bluetooth dust extraction. Milwaukee is also the same company that offers one key. And one key offers some pretty useless gimmicky features so the concept definitely isn’t beyond Milwaukee. They were just being cheap. But I’m sure Milwaukee appreciates you defending them for giving people less for and charging them more.🤦‍♂️

[@nickmilone5996]

@@steffendetrick so again, lazy shop workers don't wanna turn on the piece of equipment that is literally in their hands. If your workers are that against doing their jobs then you might wanna look into Festool. Connect to their dust collector and it turns on automatically when you use your tool, perfect for this guys that can't be bothered to turn on the thing they're using.

[@Joethetoolguy]

I think the main thing holding people back from going all in on xgt has gotta be the prices. Having said that they do make some solid ass tools

[@jefftucker9225]

I'm mainly a Makita guy but certain tools they make are over priced IMO, I have a corded Dewalt job sit table saw, Ridgid Jointer, Dewalt Planer, Bosch Miter saw, Craftsman cordless 18g nailer, as well as a Craftsman cordless 7 1/4 miter saw, as far as Corded tools I buy the best bang for the buck and go craftsman for cordless tools that cost to much in the Makita line

[@user-gb2gq8lb3s]

You (the customer) cannot win these days. Milwaukee are decent tools but could suffer from reliability, Makita are reliable but I think many of their XGT tools are way too overpriced.

[@dickphan]

bloody hell..my local tool store had a sale recently and was contemplating between Makita xgt 6 pce kit for $3100 or the hikoki 36v 10pce kit for $2200.... eventually went with hikoki....but still in the back of my mind I some how I do think Makita is better built....knowing myself I'm going to buy into Makita even with the next sale...love tools as a collector.....

[@billdavis6978]

I prefer not to continually let coworkers use my tools. They are generally rough with something they haven’t sacrificed in order to buy themselves. They can get the same tax write off for tool purchases I do if they stay out of the pub or strip club. I don’t mind here and there, but if youre borrowing my tools and blowing paychecks irresponsibly, I’m not going to contribute to your problems.

[@kevinchamberlain7928]

I switched from Milwaukee to Dewalt because I had problems with the first three fuel tools I bought and shocking aftersales. Dewalt have been more reliable for me as a carpenter & joiner but I think Makita are good enough also.

[@WIRTHAQUA]

Also run my business off the dewalt range. Love it

[@thomasgilliam3104]

Dewalts 60v line is trashing everybody. Plus milwaukee is in trouble. Dewalts coming

[@Patrick-857]

Dewalt is pretty tough and reliable but they aren't as refined as Makita. They are quite rough really. Makita tools are silky smooth to use and often times lighter and more compact. And as far as reliability goes, they are at the top. The red tools aren't very reliable from what I've seen. I run both Makita and Dewalt, but I'm finding when a tool needs replacing I'm reaching for the Makita.

[@Dug159]

At work we have Milwaukee tools provided, we have a pile of tools and batteries called Milwaukee mountain that have failed, everything from failed batteries, drills,1/2 impacts, 3/4 impacts.. will NEVER buy Milwaukee for my self, still using the batteries I got with my first dewalt cordless drill as a first year apprentice 12 years ago. (Broke the tool, no fault of the tool whatsoever) still using dewalt and just invested in the new flexvolt range. 👌

[@DVS57REBEL]

My oldest makita battery is 13 years old and just failed. They were 3.0s and never faltered in work time. I still have a few 3.0s but currently own 5.0 makita batteries along with my dozen makita power tools. Always been happy with their products since 2004

[@ron1martens]

Dadi Omega. The 5 amp hour batteries are quite good. The structural engineer I do work with has some of the 5 amp hour. The battery lasts quite a while on the grinders.

[@BraveStarEric]

Makita is the best

[@michaelbronson7410]

I've got 2 makita 1.5ah batteries i bought with their very first impact that are over 15yrs old and still going strong. Also that 15+yr old impact wzs still going strong until it was stolen about a year ago

[@shawsie5780]

I'm still running a 3amp from my Makita kit I bought in 2009 👌

[@BlueMax717]

Milwaukee continues to be in this weird position where they are resting on their laurels. Their "new" tools are the same technology from 10 years ago. In many cases they have been made cheaper and less reliable. They have the forge batteries finally but still mostly provide the 18650 packs which is just laughable. Their packout line has fallen behind pretty much everyone and they are not updating anything. Basically, Milwaukee is setting sail doing exactly what Dewalt did in the early 2000s - 2010. I've seen a TON of people switch over to Makita and Dewalt lately and it's just getting worse.

[@jreally9238]

Makita is a great brand I still have battery and drill that are ni-cad 14.4 and 18v. Don't really use them but they're my first kits I ever bought. Now I have all milwaukee mainly because in my area Makita doesn't have as much tools that you can pickup same day. Nowadays they're all good just get the ones that fit more comfortable in your hands.

[@chip9177]

on-line at Acme Tools - As I live rather remote all of my Makita was purchased from them

[@user-dy2xu3uv8k]

Lets be REAL clear here... You switched because 1 reason and 1 reason only....Makita is your new sponsor and is paying you that $$$$$$$$$

[@AddictedtoTools]

😂 cost me $5000 for this setup.

[@PartTimeYooper]

@@AddictedtoTools That track saw cost you your life!

[@Duane_the_carpenters_Sensei]

alot of these youtube tradesmen are suckers to battery platforms. i have all dewalt cordless and corded models, switched to flex, THEN switched to makita. only bought impacts and drills of each after the De-saster. batteries and chargers have nothing on corded tools, in reliability and price. i personally think it’s silly to be a slave to a platform of tools that limits you. i can buy anything corded and it will work with any and every outlet/extension cord on the job. it will all come down to personal preference then

[@clam741]

I install windows and doors and use Makita 18v and dewalt 50/50 . The Makita impacts hands down destroy all others but I do prefer the dewalt 7 1/4 battery mitre saw that I use to cut trim and simply use a 9 ah flexvolt battery on .

[@Demorthus]

4-5 weeks for a replacement battery?! Wth..

[@Lazy943]

I have used Hitachi and now metabo hpt they have served me well mate

[@bikeracerdude]

EFF Milwaukee and Ryobi- they're 100 percent Chinese owned brands now.

[@tccoggs]

All the company platforms go through cycles where they focus on a particular market and others get left behind opening the door for others to innovate and jump over them. I have more Makita corded tools than anything, however I started with DeWalt 18v XRP nicad as they seemed to most committed to the platform. With Lithium Ion hit the market, I stayed with DeWalt but they were late to the game with some tools so found myself now back in Makita LXT as well. I even have Bosch 18v batteries mainly because they hands down make one of the best 18v sanders out there. The only one that comes close is festool and that's at 3x the price. If your a Milwaukee fanboy, where was the track saw all these years?? There is no way I would have waited this long to buy one, I actually started with Festool TS55 and went to the Makita X2 for cordless over 4 years ago. The bottom line is stay within your system when you can to get the most value of your battery investments but sometimes the best tool might be outside your existing system and if it's one you will use a lot, it makes sense to be open to going outside your system.

[@markr1142]

Milwaukee aren't what they once were. Designer tools nowadays, look good on the outside with diy grade internals. All show and no go. Watch tool repairing vids. They are crap. Milwaukee tracksaw like their planer is as gutless as hell, your Makita xgt s are way better. The planer barely cuts 1.5mm, let alone 2mm.

[@cluman1]

I use Milwaukee on the job. My colleague uses Dewalt. We use each other tools from time to time. I find the Dewalt tools lighter. I also like the yellow and black. All of them do a great job.

[@patison001]

milwaukee is little higher brand than dewalt

[@aaronoconnor606]

I have both platforms as well and some hikoki/metabo hpt. They all make good tools. The makita saws are nicer than milwaukee i have the 40v miter saws the small one and the 12 inch. Milwaukee makes better nail guns so does metabo hpt/hikoki. The aws is the best part about makita i have the adapter i use with a corded vac. and have 4 AWS chips so i set up multiple tools with dust collection.

[@cuebj]

EXTREMELY HELPFUL! Thanks. As serious DiYer with limited budget who does stuff for friends in exchange for buying a relevant tool, this was perfect. I've been very impressed with my 4Amp Milwaukee drill driver pack so considered going Milwaukee for more gear. But love my Makita corded saws. Think I'll go 40V Makita tracksaw etc - matches what I do

[@ckm-mkc]

I have an older Makita 2x18v tracksaw, it's awesome. Storing the rails is a pain, but they are x-compatible with Festool if that matters.

[@cuebj]

Thanks. I have a Makita corded circular saw with an accessory that lets it work on track, so I have a piece of Makita track already. I also have some homemade tracks up to 8' / 2440mm that work very well with my 230mm blade Makita circular saw.

[@fubarnz]

I used to be Makita until 2 issues, 1 was a drill after 2 mths use drilling 3mm pilot hole would flog out bearing, shit warranty 1 year but it did get repaired, got it back and same thing happen again, they blamed me using to big of drill bit, since when is 3mm to big for 18v drill, had it repaired 4 or 5 times then after 1 year they gave money back, they would not replace it,even after 2 or 3rd repair. 2 Issue was there batteries if tool came with battery and had star on tool and you try to use that battery on non star it would run, it would start then stop right away, fuckin shit for someone using them, so basically you had to buy 2 sets of batteries for same volt and brand of tools, also the fact there early batteries didnt have balance charging so if you left battery sitting for a few weeks with low state of charge they where fucked, and if you put them on charger more than 3 times with error the battery chip locked you out and had to buy new battery, I will not buy Makita ever again due to there shit service and design, this was about 12 years ago now, gone Milwaukee now and hate to think how much ive spent on them now.

[@JarvisJiri1998]

I’m a sparky. And always been a Milwaukee guy. But recently as my impact driver and grinder has died. I felt the new impact from makita and thought it felt way better built and comfortable to use then milwaukee so decided to jump Over and get a makita grinder and impact. Really impressed with makita quality. Potentially making a switch as my Milwaukee stuff dies.

[@jensvincent4702]

Yeah…I’ve used makita my whole life and tried Milwaukee impacts and they just don’t feel right. And my Milwaukee buddies try my makita for certain things and say the same thing. Idk how to explain it.

[@mrbd9286]

I know someone who works for makita and believe me they are hiding alot of secrets regarding their dredful tools

[@craigstaples6465]

Makita didn't make the field test for us... Milwaukee has the fuel for us

[@nickrouse1738]

Are you comparing it to your old Milwaukee or the new Milwaukee?

[@JarvisJiri1998]

@@nickrouse1738 I picked up the new Milwaukee when I was in the store and the makita impact was leaps and bounds better, lighter smoother better feel. The Milwaukee grinder I had the paddle switch has a spring in it which failed early. Just seems like a robust solid tool with relies on a cheap spring to work. Now it’s useless. I opted for the makita grinder with the toggle switch just seems bullet proof. Don’t get me wrong though I love all Milwaukees tools they’re great but just wanted to give makita a try

[@OUTILSCLIPSQC]

I am a carpenter and i am fully comited with milwaukee tool ! Hey makita where are your table saw xgt and your fraiming nailer ??

[@AddictedtoTools]

The Milwaukee carpentry gear is definitely good. I’m also surprised that makita haven’t uped their game with the table saw and nailer. I grabbed the Milwaukee framing, finishing, and pin nailer. They’re awesome!

[@PartTimeYooper]

Makita has been lacking with their nail guns for awhile. I feel like they didn't want to release one unless it was better than a Paslode. I'm waiting for their table saw

[@maisummarceneiroumdemuitos8037]

They have a 21 degree framing nailer in some countries. In Brazil we have it, pneumatic one. Unfortunately no battery ones so far.

[@baseballdude8491]

Good luck with those Makita nailers😂 Rockin just one color is fools gold None of the brands have all the best tools I run multiple colors cuz I want the best tools for the job at the best prices one color fanboys are working with overpriced/inferior tools as each color has their weaknesses and strengths It doesn't take much to carry an extra charger or two and a few batteries of another color I'll keep making money with my red, green teal and a few others as u guys overspend for one color loyalty

[@whateyatalkinabout4972]

Milwaukee tracksaw is coming out February in Australia. But makita has really gone above and beyond with their XGT range

[@AddictedtoTools]

February almost seems too soon for aus. Would be good though.

[@philwort1873]

@@AddictedtoTools it is funny how milwaukee releases go. After the pipeline events in the us some tools we get super fast (M12 nibbler) some much later (track saw) some never!

[@AddictedtoTools]

Yeah I’ve always wondered how it all worked. I’m sure they have reasoning for why they release gear at different times or not at all.

[@avocadoarms358]

Australia doesn’t get the same range of Milwaukee tools as the American domestic market.

[@jensvincent4702]

You said it best. For the service type trades, Milwaukee and even dewalt are kings. Makita however, still has better quality, better suited tools for woodworking/builder applications. That said, my first combo kit was makita and I haven’t bought any other brand since, once you have so many batteries or a well established set of tools it’s hard to switch so I’ve learned to live with some of the quirks of the mechanic based tools makita offers. I’ll be going with something like Greenworks for EGo for my lawn tools though.

[@ckm-mkc]

I agree. I have Makita for woodworking, but mostly Milwaukee for working on cars.

[@Willg95]

The funny part is I'm a tow truck operator and I carry only makita on my work truck. Makita tools have never let me down. I carry a makita drill, impact wrench and recip saw in the lxt platform. I also carry the 2nd gen xgt recip saw on my truck as well

[@rooster-zg4oo]

Dewalt is known for carpentry. They make the best saws hands down.

[@pah9134]

If you can handle the price the Makita miter saw has a crazy good design compared to most. The slider is nowhere near as awkward and takes up half the bench space because it is side mounted not rear mounted. I think, with a few exceptions, Makita seems to put more effort into the design process of their tools.

[@daifeichu]

I first started using a cordless drill, Makita, in 1989. Then got a Dewalt then back to Makita. I use to think it was a good idea to only run on one platform and back then it was a good idea but now I run four platforms for different reasons. I really see no reason to run only one and only one. The only downside is you need multiple chargers which for me isn't a big deal. Each maker has their strengths and weaknesses so I just take advantage of multiple companies strengths and don't bother with the weak stuff.

[@jairoguzman4631]

Have you tried the charging adaptors for 50$ Amazon ??? Any brand any battery

[@daifeichu]

@@jairoguzman4631 No, I haven't. I don't have any need for an adapter. I've got batteries for all four systems. In fact just a few days ago I got back into Dewalt so that now makes it 5 platforms.

[@chazschuck9017]

I'm the same way. I've got M18, M12, LXT, and XGT. Doesn't bother me as much as most people to drag a few extra batteries around. I do use mostly Milwaukee for work (electrician), and mostly Makita for home use (woodworking, general construction, etc). However I mix and match plenty, and always prefer to be able to choose between each platform for each tool, and get the highest quality.

[@bensonmcnab8082]

Started on Makita but went to Milwaukee about 12-13 years ago as they had a good deal I couldn't refuse. I still have the original battery. I agree as plumber Milwaukee has some products that work better e.g. the new 12v sump pump and the 12v small tools as they fit into tight places. Also to note the 12v vacuums that fit into the hammer drills are pretty cool as they fit into tricky spots. But def the power advantage with Makita plus the bluetooth would be cool. But it all depends on the type of work your doing. I just hate how you have to lock into one product. Pick what works and don't be afraid to look at new things or think differently. Also I like the idea of the coffee machine Makita does, I could def do with that in the tool box.

[@TheFatherOfPizza]

Get the multitool for 40V Makita, it's brilant

[@trevordyson8882]

Great explanations. I would do the same.

[@RuBrasil]

Same here, Milwaukee have very powerful tools that kills the batteries earlier than expected. I love my Milwaukees but now almost always order makita ones just because the electronics in tools and batteries make it last forever. For example I made a very aggressive use of grinder to cut and polish rocks, this cause i have to order 2 or 3 batteries per year! Makita 40V the battery have more than 18 months, the tool have a special sensor that slows down the tool when battery is too hot to don't damage the battery. I save several hundred dollars with makita compared to Milwaukee. And Inlove Milwaukee ❤ but they are far behind in battery management.😢

[@fecalmatter4195]

I went Milwaukee last year have had a couple issues with a battery and circ saw and been eyeing off Makita 40v range lately however the worst problem with Makita is no framing nailer. I'm a handyman so I need just about everything

[@AddictedtoTools]

What circ saw problem? Mine had bad trigger problems. Worked intermittently which was painful. Nail guns have been a let down from makita. Not sure they haven’t kept up. I’ve been loving all the Milwaukee nailers. Cheers for the feedback👌

[@kevincedeno8899]

I've spent a shit ton on Makita tools for woodworking and properties management. Always a pleasure to use them. I've also saved some money by buying their corded version like the electric planer and the miter saw which is by far my favorite tool. Even the wife gifted me the handheld vacuum and subcompact line knowing that's gonna end up being used around the house. But when I see a builder using heavy Makita tools for framing, HD renting them, and this summer saw Disney World maintenance crews using Makita at their resorts, it reinforced my choice.

[@dangrimes5078]

At least it was a shit ton and not a shit load.

[@Willg95]

I've been on the makita lxt system since I bought my first tool set back in 2013. Which is still going strong to this day. But have since been replaced with brushless models. But still get used often. My brushed impact wrench has been relegated to home use and replaced with the brushless high torque impact wrench for my work truck. My brushed recip has been replaced by the xgt 2nd gen recip on my work truck and relegated to light duty home use

[@kevincedeno8899]

@@dangrimes5078 Yep, definitely makes a difference. Lol

[@AlexKall]

After watching a certain Irish bloke repairing tools from the big major brands I got even more sold on Makita, who actually think about making them repairable without it costing more than 50% of the tool to repair.

[@riba2233]

Yeah Milwaukee batteries have really rudimentary management pcbs inside unlile makita xgt ones which are latest tech. They won't have similar issue and won't go out of balance

[@dannynimmo3052]

Thanks for this info. I'm retooling right now, I just gave all my milwaukee tools to the contractor that just did my bathroom, he was just getting started, did a great job and probably didn't charge me enough for the bathroom so I gave him several bonuses like that and will use him again. all the makita stuff I have like the floor plainer all is plug in, I could still go either way. Great video, again thanks, I needed this right now

[@jaydenheidtmann7811]

My current problem is iv gone dewalt from day dot now i gots a new job and everyone runs makita

[@jeffb321]

Ive been running 18v makita tools for about 12 years. There great, i have over 50 makita tools. The only issues ive had are with the multi tools. Ive probably had 8-10 of them iver the years. Dewalt and Milwaukee especially are SO UNCOMFORTABLE in the hand. Its like the designers and engineers never even put the tool in their hands. All my Makita tools fit my hand like a glove and give me complete confidence in the task at hand.

[@packoutjunkie5813]

You make some valid and great points. I switched from DeWalt about 4 yrs ago and have went strictly Milwaukee. Overall I am happy. However the Mitersaw, lack of AWS and issues with 12ah batteries have dimmed my excitement as of late.

[@brandonhoffman4712]

For miter saws I just love Bosch's cyborg arm. For the money it's the most robust system to counter deflection I've seen. Even better than those new arm style saws that have tried to copy bosch have done an inferior job. Mine survived a car crash and still slices and dices. The truck didn't fare as well, (I was not there). It's an older plug in model. I don't think for bigger tools I want battery power, I want robust power, quality dust collection, and dust collection that can turn on automatically with any tool I plug into it. Plus I don't want to get stuck waiting to charge. Not sure what your issue is with the milwaukee 12ah? I've never had problems with them other than taking forever to charge. But that's because you need rapid chargers for the big batteries. Heck if I was using 12ah ones a lot I would consider the supercharger. It charges a 12ah in 1 hour. Capacity wise, the m18 12ah has more capacity than the makita 40v 4ah. It's like a 40v 6ah battery.

[@Ordog213]

Thats why i got Bosch Pro for everything in my home. I am no Tradie in any form, but the quality is for me the best, and you get some nice bonuses from Bosch. I Bought a tool set with SDS Plus Hammer Drill and an Drill for 329€, but you can get additional things from a programm called "Pro360". For the set i bought, i got an additional Impact 1/2" Impact Driver and two 5 amp 18v batterys for free. That and i can walk in the Bosch Shop a town over, drop of my defect machine and get a replacement right there. And Bosch startet AmpShare, a system for share batterys over different tool companies

[@jackrayner3296]

Ryobi is the best but

[@jackof1]

Skil fo sho

[@redrem4553]

Yeah the best if you smoke meth and cant afford tools

[@jackrayner3296]

@@redrem4553 how dare you assume my gender

[@PartTimeYooper]

Craftsman

[@kadynhassan551]

you forgot about ozito bro

[@jonathangarzon2798]

Festool is overpriced, the reason the users love it is because they can't take the hit on their ego by admitting they made a mistake. Like buying apple

[@gorkyd7912]

I just get used Ryobi tools on craigslist and write "Festool" over the logo with a sharpie, seems to increase performance.

[@AddictedtoTools]

😂 I’m going to have to try out some of the gear to see what it’s all about. Better not be hype

[@kierenpayne2661]

I run 18V Makita and 12V Milwaukee. Makita drills have constantly let me down but maybe I asking too much from them using holesaws although there was one model that was fundamentally flawed which many people I knew had the same problem. Anyway, apart from that I have flogged the Makita’s and they are great. You are correct in regards to Makita being better for carpentry as every Chippy I know runs Makita and/or Festool.

[@RagingShadow101]

As a Sparkie you used the word “cleanup” a lot, can you expand upon what that word is?

[@stephrc6647]

I am a makita man for my work but use the Milwaukee packout tool box’s due to their drawers and the quality and strength.

[@sic04250f]

At my workplace majority of gear is Milwaukee and very few makita, biggest problem with Milwaukee is the way the battery connnects to tools. Our tools cop an absolute flogging, after time the Milwaukee tools don't attach to the batterys as well and power cuts out. Long term Makita any day of the week.

[@philwort1873]

Great video. I am on a few of the battery platforms. I would say that you will probably want a table saw when it comes to fix out depending on how detailed your job is. All the best with it!

[@nfi2nfi2]

The Makita mitre saw is leagues ahead of Milwaukees. 😂 Milwaukee wouldn’t even be in top 5 of mitre saw

[@cahg3871]

“Never tie yourself to one brand”-good advice I received by the tool associate at Home Depot.

[@richymoto]

No ... buy a truckload of batteries and chargers instead ;-)

[@w0kepatriot441]

I run a lot of milwaukee but realistically sticking too only one tool brand isn't possible. You just can't get all the best tools from one manufacturer. Stabila for example is leagues ahead of milwaukee when it comes to levels as they should be. We run max framer nail guns and a dewalt compressor. Chop saws and table saws aren't really brand loyal either considering we still usually use chorded for those two. Brand loyalty is just foolish .

[@MultiMartien]

Not if you work with batteries

[@gorkyd7912]

@@MultiMartien Even if you work with batteries. If the tools are the same maybe it doesn't matter, but if you want a cordless chainsaw you simply can't find a good Milwaukee cordless chainsaw, you'll need an Echo or DeWalt. You're better off getting 2 batteries and a DeWalt than trying to get regular work done with a crappy tool.

[@w0kepatriot441]

@@MultiMartien I honestly don't consider battery tools to be enough for everything at the moment. Pneumatic nail guns are impossible to beat and so are chorded table saws. I already use metabo and milwaukee when it comes to battery stuff and I only use gas chainsaws. Battery tools just aren't up to par with the older tools yet. Of course there are exceptions but most of those are fairly cheap to mix battery platforms. But im more of a general contractor I do all kinds of random shit. A plumber and electritian I could see sticking to one platform a lot easier than i can.

[@MultiMartien]

@@w0kepatriot441 have you seen the new 40v compressor from makita its perfect couse you are right about air gun shooting.

[@w0kepatriot441]

@@MultiMartien I have and I actually currently own the smaller milwaukee battery compressor. I think you could get away with just that as a subcontractor for sure. Even framing you could run those pancake compressors they just don't keep up as well as a large wheel barrel compressor. Honestly im willing to bet within the next 10 years pneumatic guns could be completely replaced by battery if they can lower the weight to a more usable level. At least that is what I hope.

[@kelsie9912]

That extraction system is awesome! Would love to see a video of how you set it up when using it for different tasks

[@martylucas8557]

Excellent comparison! As a Milwaukee bigot I have to say you were spot on with your comparison overview. I have over 30 M12 and M18 tools, plus 20+ Packout boxes and bags. So I’m committed and for the most part very satisfied. Milwaukee builds some excellent tools! However, I believe they’ve missed the mark with their new vacuum line, which looks excellent. Not having BlueTooth connectivity between vac and tools is a major miss. How the hell could that even happen?

[@MrLocke-bk3om]

And lack of dual power is also a huge miss. Having to ONLY use battery power or not having passive charging is such a stupid idea for such an expensive tool

[@DarthCuda]

There is a powerhead that has a corded or battery option. There a 3 configurations.

[@michaelrjacobs]

What's the use of bluetooth when you are connecting a vacuum hose... Doesn't make sense at all.

[@AddictedtoTools]

When you pull the trigger on the tool, the vacuum come on and turns off 2 seconds later. It’s extremely handy

[@martylucas8557]

@@michaelrjacobs , it’s simple…instead of having to reach down to turn the vacuum on prior to starting the circ saw or miter saw or whatever tool, Bluetooth from the tool sends a signal to the vacuum, automatically turning the vacuum on. After the trigger on the saw or tool is released the vacuum turns off. If your making a lot of cuts it would be really nice to “not” have to reach down each time to turn the vacuum on and off. With Bluetooth connectivity you never have to worry about forgetting to turn the vacuum on or off. It’s just a very convenient technology that I’d like to see Milwaukee incorporate in their tools and vacuums.

[@ThePeavey23]

Makita=Toyota Milwaukee=Ford

[@USandGlobal]

Yeah that’s exactly why Milwaukee is better 👍😂 those cheap Makita and Ryobi tools just can’t hang

[@whitechris720]

I have had 5 milwaukee batteries die within the 1st year. Small business, I can't wait a month to run a tool. Makita is my tool of choice. I have never had a makita battery die. My Makita miter saw 36v did die this year, but it was 5 years old. I love that miter saw, so it's being rebuilt now.

[@RuBrasil]

Sama here, done ordering milwaukee bateries, the makita XGT batteries lasts forever.

[@whitechris720]

@RuBrasil absolutely I still have yet to have one fail. I have a couple dozen, and I use them every day. Some are 6 months old, and some are 6 years old, and I can't tell the difference when I run them.

[@JamesSmith-gk8sz]

Hit the nail on the hand at 6:20 with your statement “what work are you doing and what finished product do you need?” Blows my mind watching the average house husband shelling out $500 USD for the newest Dewalt, Makita, Milwaukee, Bosch, Flex etc and then to overhear he’ll be using it to put small screws into drywall anchors to hang pictures. Most people not in the handyman, construction, blue collar trades industry *do not ever need* to care about brand for day to day house work. The professional framer who drives structural screws all day long definitely cares which impact driver, rotary drill, or impact wrench drives the quickest and easiest and which battery runs longest and best on it. As a PSA, please stop buying top of the line gear for household DIY stuff. You can get the cheapest most off brand piece of crap on the market and it will do the job of hanging those pictures just fine.

[@AddictedtoTools]

Cheers mate. I fully agree. A lot of the time the tool will only be used a few times. Don’t have to buy the top or the most expensive

[@dalemcdermott9840]

I’m on the Milwaukee and makita xgt platforms, I can’t honestly say I could be on either platform fully! The Milwaukee 16 and 18g and framing nailers are phenomenal and they have tools that xgt just don’t make yet. I have the xgt mitre saw, 190mm saw, combo drill and impact, recip saw, planer and track saw that Milwaukee just don’t compete with

[@Alex-uh1mj]

Dont compete on the recip saw?

[@Hobiee90m3]

@@Alex-uh1mj yeah the recip saw from Milwaukee is the staple but the new flex looks pretty good too, coming from a dewalt guy

[@mjolnirswrath23]

I expect them to DeWalt tools going from Porter-Cable junk essentially saved up earned it bought it bought the kits when they had the battery included or multiple batteries and chargers etc been running for about 5 years now non-stop Trim carpentry rough carpentry beam work you name it and it's been going non-stop however DeWalt makes really poor nailers in the cordless range so I use battery adapters from Amazon and been running those for about that long too for my Milwaukee nail gun Brad nailer and 15 gauge by dewalt batteries are still going strong they have never had an issue They seem to have a better system and backup system One thing I have noticed is a lot of people that use Milwaukee on the job site They have battery issues also the bearings go out on their tools especially the impacts and the drills and the same goes with Makita The batteries go out especially if it's cold they do not like cold at all My DeWalts will run in the cold No problem I also was smart about it and built a battery box with two chargers so that when I'm charging my batteries it's also an insulated box it's got two fast chargers inside and then I bought Amazon battery lockers to go on the walls of the inside the box so roughly I have 15 batteries ranging from 5 9 ampere hours 3 6 amp your hour several 2.5 and and a few fives I never have a problem with it I would like to get a 12 amp per hour but I think I'm just going to go with the cheaper brands the knockoffs and see how they do if not then I've only lost maybe a hundred bucks and I can get them replaced versus paid $250 a battery or $375 for a 15 amp I do plan on getting a 23 gauge Makita and then getting a battery adapter so I can use my batteries it's all the same voltage 18.6 volts the whole systems are

[@clarkfos3447]

@@Alex-uh1mj The new Makita XGT avt recip saw is faster than Milwaukee.

[@Alex-uh1mj]

@@clarkfos3447 ah okay, ive not seen any comparisons yet. Im too heavy invested in Milwaukee now 😅 better not watch

[@Eldalion99999]

from what I saw and heard, milwauke is overprized for no reason, there are no additional benefits/stats that justify the cost. And for haters: yes I do have money for every single red-lambo tool. There is just no reason to go for it

[@AddictedtoTools]

I do agree. Some of their tools are competitive on price but most aren’t and what Milwaukee has done for years now is they’ve marketed extremely well. Once you can become the brand everyone has and talks about, you win the game. I believe they do have some extremely good gear. But only a few items that are worth more.

[@ChristIsLord229]

Makita is the best!

[@MadLadCustoms]

Milwaukee - Class Jock DeWalt - The Wrestler Makita - Quiet Smart Guy

[@duanekellen9427]

Next to festool Makita has mitersaw’s

[@marcgebeloff2036]

I spent a decade doing similar work, larger scope interior focused remodeling, which almost always includes a decent amount of cabinetry and finish trim work, before finding my current specialty. These types of remodels are so broad in scope they have the widest requirement for power tools compared to more narrowly focused trades. That makes these types of outfits very good judges on tool platform choices. They regularly use such a wide variety of equipment ranging from hammer drills for light concrete and tile demo to fine finish tools like track saws and and routers. I’m sure this guy has lots of secondary tools they use often but not every job

[@ron1martens]

Marc. I'm a plasterer by trade. Although I had to diversify to cover many aspects in the building trade simply to remain in work. I have tool boxes for bricklaying, concreting, carpentry, plastering, ceiling fixing, tiling. I did maintenance work such as using demolition hammers. Moving into the battery range. I do wish to purchase a cordless mid size sds max demolition hammer. I have the metabo 18 volt sds plus rotary hammer. Its pretty good. I did have a 36 volt metabo4 amp hour.It got stolen along with other tools.So I replaced. Yes, I'm also a tool person. It did get me work however. I get asked can you do this? I say yes I can. Sometimes I don't know how. I figure a way and just do it .

[@rn1985]

Milwaukee batteries are trash. They are completely sealed. Imagine heating it up by being discharged on a grinder and then being thrown on a charger with no air circulation 😂

[@maisummarceneiroumdemuitos8037]

agree, how can a excellent tool brand like Milwaukee uses this old school batteries? My $20 flashlight have more advanced electronics than Milwaukee batteries.

[@amiscauich]

When I first started carpentry I started with all Dewalt because everyone else had makita. Then I made the change and it was for better. Makita may not be the strongest but they sure are the smoothest and quietest tools.

[@MrTmone2169]

All day

[@markcrystaltownsend1578]

Bosch are under power but even smoother than makita . Especially when using their better stuff . I rate there drill Especially I don't own one but the one's I've used in the past felt better than drills twice the price.

[@Crissecrisse98]

They sell adapter for battery now!

[@tedbownas2748]

I've had Makita drills since 1987, although I bought a number of Ryobi tools between around 2005 and 2015 as their line expanded quicker and at a lower price point. The past few years, I've gone back to Makita with the LXT platform, and I love them. I'm hoping the XGT platform doesn't result in them phasing out the LXT line. 😬🤞

[@maaduece5132]

I talked to a rep the other day he said that it wouldn't be , that the xgt would be a pro line and 18v would become a home handyman type of product

[@danovichi]

Yeah, their LXT stuff is here to stay, at least into the foreseeable future.

[@pablosetien5548]

By the 80s Makita was all made in Japan , current Makita are made in China, I don't think is the same quality.

[@travisjazzbo3490]

@@pablosetien5548 Makita is made in about 13 places, not just China. They have specs they have to meet in China. Most tools are made there. Makita is still the best overall quality

[@mikeznel6048]

Makita gives you more tools and more money. That’s why.

[@AddictedtoTools]

Hey mike, could I ask why you believe this? I’m literally $5000+ down with this setup.

[@OiBriffa]

I think Milwaukee is a whole lot better with mechanics too

[@AddictedtoTools]

Yeah they definitely cater to the mechanics👌

[@plasticbmw]

Damn that Bluetooth extraction is probably so nice to have

[@red_rocket.]

Another great video thank you. Makita have been top notch gear forever and before I started my plumbing apprenticeship in 1975 at 15 years old. They always set the standard for the others to achieve.

[@keithburt4734]

What would you rather do run around for batteries and chargers or plug a cord in once.

[@cackle067]

What an absolute load of crap There are several Milwaukee tools that leave makita for dead There are some makita tools better than Milwaukee To say makita is the one setting the standard is garbage Give me the Milwaukee angle grinders over makita any day and their impact drivers and impact wrenches and grease guns Would go makita for their saws is about all Makita impact drivers are nicely balanced but Milwaukee grunt kills them

[@CrossCut_Custom_Builds]

Not true Makita has always been behind Dewalt and Milwaukee in innovation. Not to mention no high output batteries for the 18 volt line.their impact drivers do not cut it if you're driving big fasteners. I have their cordless track saw which I like except battery life is not great thanks to outdated technology.

[@thewholls7176]

As you will know, it kind of doesn’t matter for around 20 bucks on eBay you can buy adapters that will convert between Milwaukee and Makita - as long as the voltage is the same…….. I’ve had Milwaukee for three years at the DIY level never had any issue

[@theimprovementsguy8871]

I have 90% ryobi. 10% makitia battery tools..

[@MrDontcareify]

Makitas new XGT line is absolutely beautiful and top of the line tools. That said, Milwaukee also has good tools as well.

[@emiloss91]

My first platform was Ryobi (in EU), but they have so expensive and big batteries, that I want to change it. So I change to DeWalt and for now it;s really brilliant and really much greater than Ryobi (you can feel the difference). But its funny that people say "only makita!" or "only milwaukee!". C'mon... Of course it's expensive to get two systems, because you have to buy a lot of batteries and chargers, but sometimes it's worth it because one tool in milwaukee can be a crap but the same tool in makita is brilliant. So as you said - just pick up what you need and try to find platform where your daily tools will be the best