That is a great video! I was trying to figure out the TU/TD shifting on my own and had called Lokar to ask them for some help, they referred me to your video. Perfect!
@ntdracing2 жыл бұрын
Perfect. Hope you can get it to work.
@chrisrundlett37072 жыл бұрын
@@ntdracing Me too! Is there any reason for the shift signal to go through a CAN Bus gateway or does it make the most sense to just wire it directly? I am guessing that the signal being sent to pin seven is just telling the TCU to shift up and down and that the TCU is telling the ECU what gear it is in through one of the other pins correct? Sorry - I am really new to this, figuring it out slowly...
@josephmora50509 ай бұрын
About ready to tackle mine… I had a few questions. I bought a new 6l80 from GM. They actually have a set up for pin number 7 on the trans. I have two connectors, a two prong and a four prong. I was curious to see if I could get some help. I’m also a little confused the actual wiring from the shifter as to where they go. Im a bit new to this so sorry for my ignorance. Im sure your schematic explains it all but im still learning 😊
@PierAcerni2 ай бұрын
What a great tech video man! huge thanks from the comunity...
@nicledbetter96898 ай бұрын
This video is great! But I struggled with mine for two months, rewiring, reflashing, etc. Everything was right. I finally found a post by V8R on that same HPtuners thread. I needed to set U0121 and U0140 to do not report. These are codes looking for BCM and ABS module. This change allowed TUTD to work perfectly.
@RyanBaker3 ай бұрын
This was the best informative video I have come across for this modification. Thank you very much!
@ntdracing3 ай бұрын
Thanks. Hope it works for you.
@AbstractDreamz2 жыл бұрын
Just programmed my 6l90e with Kilduff horseshoe with manual mode! Thanks for the video!
@GenV_Restomods Жыл бұрын
Spectacular info, greatly appreciated. Now got get yourself a Gen V LT1/L87 and the 8L90 or the 10L90, that's the ticket.
@ntdracing Жыл бұрын
Just put in TH400s. Going backwards. Thanks.
@AbstractDreamz2 жыл бұрын
100% awesome video that came at the right time for me!!! 76 Buick Regal restomod. 6.0 L96/6L90E
@plutorootswoodworking Жыл бұрын
Anything funky with your swap? I’m buying a 1966 c30 that’s got the same combo (l96 / 6l90e). It randomly throws a p150A code but runs, sounds great and drives other than throwing that code. The guy who did the swap kept the stock harness, I’m wondering if I’m better off ordering a standalone harness from psi and starting from there.
@brandonloll42622 жыл бұрын
Man I wish someone would figure this our for the 8l90! awesome job.
@David-ir9dx2 жыл бұрын
Great job and a great resource! Thanks for putting this together
@bogdankril2 жыл бұрын
Love your videos. Thank you for the Friday night special release. I'm committed to leaving a comment for every video you post. I know it helps. Have a great weekend.
@ntdracing2 жыл бұрын
Thanks. The comments really help.
@J2A612 жыл бұрын
Thank you so much for this video I have a LT swap with the Lokar shifter and didn’t have a clue as to how I was going to make it work… your right on time with all the answers, THANKS!!! 👍🏾👍🏾
@ntdracing2 жыл бұрын
Nice! Any shares are appreciated.
@J2A612 жыл бұрын
@@ntdracing I have a time lapse of my genV swap on my channel, I actually just had it tuned about a week ago and the shift points are off. But with your help I’ll be able to shift it manually so that will keep me from trying to get the tuner to fix his mistakes. (Which is hard🙄) sadly most of these guys just take your money and don’t own up to their mistakes as a tuner. But oh well it is what it is
@J2A612 жыл бұрын
@@ntdracing so to be clear this is one wire and jump the squats together using resistors in the right location?
@ntdracing2 жыл бұрын
@@J2A61hope this answers your question. 12V on one side and pin 7 on the other with some switches and resistors in the middle. 0V = Trans in normal drive mode Move the shifter to sport. Engage one switch and resistor = Trans in sport mode waiting for a command. Tap up or down. Engage two switches resistors to send a shift up or down signal.
@J2A612 жыл бұрын
@@ntdracing yes sir, your the man! Thanks for the rapid response I’m wiring this up as we speak
@thomaslapointe4671 Жыл бұрын
Great Content & Video Sir. ~ Wanted to use a Tundra TUTD Shifter in a 96 Toyota T3 Locked Land Cruiser w 416 (LS7 Crank & Ti Rods Stroker w Aussie Transfer Case adapters to a 6L80E Thank You, So much ~ the knowledge, tools, ECU editing ~ Control Synergy 😎
@meandmissy1970 Жыл бұрын
Great information. Thank you 👍👍👍
@mikematthews24792 жыл бұрын
Can’t wait to try it! Thanks Dave!
@LucasGabriel-lw4os Жыл бұрын
Good morning, is it possible to have a more detailed diagram on the connection of the sensors because they are 3 wires each and the lever has 3 so there are 9 wires, and in the video you show connecting only 3 resistors, and a better explanation about the connection is possible?
@josephmora50509 ай бұрын
This would be soooo helpful! Better yet if you can walk me through it ill make a video for the people and give you the credit! 😊
@richpryor56372 жыл бұрын
Wow! Great job Dave.
@MrBanks532 жыл бұрын
This is EPIC. Exactly what I was looking for!
@ntdracing2 жыл бұрын
Thanks for watching.
@ronfreitas14562 жыл бұрын
Thanks for the awesome video! very informative and helped me alot.
@HAMMER_2.27 ай бұрын
Great video!! Im thinking of adding the same Sport shifter to my OBS Chevy baja bulld! Could you possibly do a huge favor for me and tell me approximately how many inches the lever sits when in park and D /as far back as it goes? This console we built has a limited opening for the shifter lever. It was originally built around a B&M stealth shifter in which the Lever basically stays in place, only ratcheting nack & forth about a half inch. Im hoping the travel of this Lokar will fit within my constraints I have. Thanks man !
@mamz14042 жыл бұрын
اللهم صل وسلم وبارك على عبدك ونبيك محمدﷺ
@ResurrectionUph Жыл бұрын
Well made video
@davidlassiter77692 жыл бұрын
I need to check the Shifter I got for the ‘81 CJ-7 to see if it has the speed shift mode.
@ntdracing2 жыл бұрын
If not, you should sell it to me.
@newergonnausethis2 жыл бұрын
Fantastic video! What a great job! Question: Could this be made to work with button on the steering wheel and the stock column shifter? (Given that I can get the lever into the correct position). Could this work i "D" and just have a switch to activate TUTD mode?
@britman1856_4 ай бұрын
9:25
@filiptrojanek5083 Жыл бұрын
Very informative video. I am reviewing all of the supporting docs you listed right now. It look like the link to the 6L80/6L90 manual is broken. Do you have a PDF of this you could make available? Thank you!
@ntdracing Жыл бұрын
I will look. Seems like that doc is a moving target.
@jamesmccombs-fb5rw Жыл бұрын
is it possible to have a more detailed diagram on the connection of the sensors because they are 3 wires each and the lever has 3 so there are 9 wires, and in the video you show connecting only 3 resistors, and a better explanation about the connection is possible?
@ntdracing Жыл бұрын
I will try to work on something. In the mean time you can think of it like this. 12V positive from your battery goes to all three switches on the shifter. I think I used the black wires for 12V in. The red wire on the main shifter becomes hot when you put the shifter into sport mode. This red wire goes to the 8.25k resistor. The tap switches are different. Black goes to 12V (your battery). Blue goes to either the 4.42 or the 1.5. After the resistors, all the wires come together and are pugged into pin 7. I sure hope this helps. If you have the wiring correct and you test it like I do in the video, make sure you follow the steps to get the HP tuner part right. Specifically the part when you figure out what gear the computer thinks it is in when you move the shifter to sport mode and activate the 8.25k resistor. Good Luck
@K4gixxer10002 жыл бұрын
Great job! if you could make me something to get my tutd off the column in the 14-18 silverado/sierra i would pay good money!
@newergonnausethis Жыл бұрын
Is the shifter/lever still in "D" or is it needed to go to the next detent "M" for this to work? I'm being told if I program it to "D" I will have to go to neutral and back to "D" to disengage it.
@dsr_swap Жыл бұрын
Yes, you're right. If you program it to get into TUTD mode from D, in order to be in Drive mode, must go N and then D again.
@newergonnausethis Жыл бұрын
@@dsr_swap OK! So in the Lokar case, you have to go to sport/TUTD. Then back to D then ratchet to N and back to D to release the TUTD?
@dsr_swap Жыл бұрын
@@newergonnausethis yes sr.
@candyman19672 жыл бұрын
Can I just make it a sport shift with buttons and no TUTD I have a stand alone fuel injection motor and just want to be able to shift the 4L80E manually
@jimcollins9316 Жыл бұрын
At 18 minutes, approximately how fast were you going?
@dandorris85312 жыл бұрын
Just stumbled on to this great info. I didn’t know those trans could handle that kind of thrashing. What kind of upgrades were done to the trans to make it survive? I actually acquired one of these believe it’s a 90E but not sure how to identify the difference. Pulled from a perfectly driving vehicle.
@ntdracing2 жыл бұрын
I think the trick is to keep them cool. We melted one down at Vegas to Reno. Hit 270 degrees. Since then we have quadrupled the size of our trans cooler.
@arongoulding50692 жыл бұрын
Would this same principle work on a 4l60e
@stephendudla2 жыл бұрын
What wire did the resistors go onto do you have a wiring diagram for the harness you built? I just purchased all the items in the description
@ntdracing2 жыл бұрын
I electrical taped them to a popsicles stick as a strain relief. Pretty high tech.
@stephendudla2 жыл бұрын
@@ntdracing I'm trying to wire mine I'm no electric expert so the NO/NC thing I'm confused lol did the resistors go to the blue wires black goes to ground and red to 12v?
@abdullahkhalidch5401 Жыл бұрын
Hi everyone, Any guy one who is facing issue to go back from Sports mode to D mode?
@ntdracing Жыл бұрын
Need to go to Drive then cycle through Neutral. Works for mine. Good luck.