Adjusting Accel Pump | Tech Tuesdays | EP10

[@jasonriede6056]

I learned a lot from your guys video keep them coming should help with people answering phones all day

[@FiTechEFImedia]

Awesome, so glad you like them! This is why we make them!

[@danielf7055]

you need to do a video explaining the difference in injector sizes

[@andystote9489]

Hi is the Summit 500 system similar to the Fitech , this was very helpful and clear information thanks Andy

[@BernHardMotorsports]

Excellent video this was just what I needed

[@cyrusvirus6928]

if i’m having knock at kickdown under load, do i adjust these settings or afr?

[@WayneMontes-mh7bp]

Hi my name is wayne i Have a 71 chevy c10 i don’t Know if i go with swap 5.3 Or efi fitech system what do you recommend me? Let me know thank you

[@southsidetv1105]

I use an Aeromotive 5.0 variable speed pump that adjusts based on TPS voltage. Will this fuel pump affect the system negatively

[@HornaksLiquorDepot]

I have 38350 ecu, with a accel super ram intake. When I had it actually driving it was hesitating, and letting off gas going lean then rich and bogging down and wanting to die. So I'd like to know if you could give me some accel pump settings to just start with. Car idles great but when I Rev it now it has a backfire

[@FiTechEFImedia]

Check fuel pressure, including when tapping on the throttle. If fuel pressure drops at all it will get worse under load, this could be caused by a restriction in the fuel line ( clogged filter, ect)

[@upholsterybyquan7512]

I have a ls 6.0 my sound like I’m at the Rev limiter at 3500rpm but it’s set at 6600rpm what’s not set right

[@philh9238]

So do you adjust both at the same time? Fast accel and accel at the same time

[@joemiller6278]

I always have about a 1 second delay after coasting then accelerating or even stomping on it at a dead stop. After that 1 second cutout it screams.

[@5_lug]

Thanks, nice and very helpfull episode

[@FiTechEFImedia]

So awesome, thank you!

[@justplayin6859]

I email you guys three times no reply

[@FiTechEFImedia]

@@justplayin6859 Hi, what is your email address, I will get in contact with tech and see what is going on.

[@perryg5500]

My problem is a surge ( and sometimes stall) on cold and mostly hot start up. My accel pump readings are 0.0 , -10.2 & 20.3. What should they be?

[@cyrusvirus6928]

i was having a similar issue and i found out i had a vacuum leak via intake gaskets

[@lowhombre]

Would this help if my engine seems to be running too rich at idle and cruising? I smell like gas whenever I drive my mustang with the fitech system.

[@FiTechEFImedia]

watch the AFR video for idle and cruise tuning of fuel. Also always worth checking is the FAULT CODE section of the handheld.

[@lowhombre]

@@FiTechEFImedia Thank you 👍🏼

[@GoldStandardTrains]

Would this help with a stalling issue? My car is stalling after deceleration when the car is warmed up. Usually after a rolling stop, and sometimes after full stop. Sometimes coming to a full stop the car wants to stall and I have to give gas to keep it from stalling. Once i go to accelerate, the engine is just cutting off. It starts right back up, but it will do this on almost every trip I take usually on the return trip back from where I'm coming from(5-10 mile trips).

[@FiTechEFImedia]

Check out our IDLE CONTROL video for help with the issue you are describing.