Adventure Force Double Fire Mod Guide

[@reesemolloy6109]

A example for a air restrictor is that when the darts go in it pushes the posts back for air, and when you shoot the blaster that slams back to close it and adds air tension which slows the plunger down so it won’t smash into the plastic, but when you remove this it allows better flow, but if you remove it dry firing is bad because it allows the plunger to slam on the gun possibly damaging the gun and snapping it

[@Mooloo17]

I have one myself, I tried to mod it just how you did, and it was great. Thanks so much for this guide

[@maritimefoam]

You’re very welcome! I hope it went smoothly for ya, the solvent weld was really annoying

[@michaelbosley6303]

The solvent weld didn’t budge. The plastic of the dark grey bit gave way first. Going to eventually buy another, any suggestions on how to get the solvent weld undone without risking breaking another one?

[@noxxeexxon]

Note to everybody is don't try to pull the string while it's not done, I tried to test fire it and a plastic part snapped!

[@DungeonTracks]

[Insert obligatory Evil Dead joke here]

[@maritimefoam]

Good? Bad? I’m the guy with the Nerf

[@Looney_ToonZ]

To quote from one of if not the best movie franchises of all time….Groovy~

[@maritimefoam]

One of my favourites of all time!

[@CutGrassGoFast]

This is helpful mine sucks so I decided to saw of half the barrel and this will help with power

[@Zomb1e_Bonn1e]

thanks man! I broke this blaster and you were able to help me!

[@maritimefoam]

That’s my favourite thing to hear!

[@arcilYT]

Thanks for this 'tutorial❤ this is my first time modifying a nerft gun and I feel like im an expert now

[@maritimefoam]

Nice! This is how it begins haha!

[@Mooloo17]

The cap that you shove darts into is backwards. Lol😂

[@maritimefoam]

?

[@Mooloo17]

15:37. You put on that black cap backwards.

[@EverythingZen01]

It would be cool if you could find a way to remove the stock. It's the weakest link for sure

[@maritimefoam]

Yeah, unfortunately the stock houses the pulley bit, though I think Jolt King modded one to be rear prime if I’m not mistake? You should give him a follow for sure!

[@josephgrant4636]

I'm halfway through this mod, I went in it with the plans of chopping the handle any way possible, fully ready to mount ew posts and shorten the string, but you'd need a whole new smaller plunger system. It's just a little too big to remove the handle. So sawn off barrels it is

[@SkkiterSkkater]

I took a hacksaw to the barrel and made mine into a Force - A - Nature.

[@maritimefoam]

I keep meaning to do this!

[@Giosuke_Giogashikata]

My intention with mine is to paint it up like a super shotgun A La Doom 2016, with a gunmetal-red-orange gradient on the barrel to make it look like it’s overheating.

[@bigteo90]

Okay thanks to you teardown I know I just stupidly lost 2 pieces😭

[@maritimefoam]

Oh no!

[@bigteo90]

@@maritimefoam it's not that huge of a loss I found it in the garbage so it's more of a learning experience and I managed to find one piece and put it back together.....it only fires once tho

[@dennisbyers1784]

I think I'm gonna do that before I paint and kitbash it to look like a flintlock shotgun

[@maritimefoam]

I really need to get into painting. Just need to pick a project and go! Maybe I’ll do this one as well!

[@chips9263]

You should make a sawn off version of this! I’m not sure how, though.

[@maritimefoam]

Ha, I’ve been meaning too, maybe I’ll do that this weekend!

[@theggeneral3942]

I did it, aesthetics are nice, feels so much cooler too!

[@maritimefoam]

@@theggeneral3942 that’s cool! Ok, I need to short list doing this, it wouldn’t even take long :)

[@tdog-jy1pp]

I did it to one of mine plus filling in some stuff to make the stock look like one piece

[@maritimefoam]

@@tdog-jy1pp nice!

[@wardrich]

Dude, you're a lifesaver. I opened my son's to fix it and didn't have a proper surface to work on, the thing nearly exploded itself on me lmao. Gotta re-watch though, the rope that connects to the air tubes on mine has a spring and I didn't see where you connected it. [EDIT] Figured it out, but knocked a spring loose near the pulley at the back, now trying to figure it out 🤦‍♂️ [EDIT] Pulley spring - straight end goes through the slit in the peg for the arm. The other end points 90° down, and will catch on the plastic spine that spans the top and bottom of the stock, just before the seam of the butt of the gun. The other nuance is that the part that pulls out the arms has to have the plastic horizontal bar closer to the bottom of the gun so that it catches on the black piece that's screwed in (at first glance it doesn't seem to do anything)

[@maritimefoam]

I’m so glad you made it haha! I remember it being a pain. Also i love the updates!

[@tdog-jy1pp]

At least theres an actual mod video of this blaster. I just recently bought 2 of these and there are both gonna be modded quite heavily

[@maritimefoam]

Awesome! I hope it helps! Take your time with the solvent weld and removing it!

[@TheBoxManYT]

I ended up breaking the pole that held the pulley in place while taking it apart

[@steeef54]

Looks awesome

[@maritimefoam]

Hard to beat for the price! I have a short of me firing 6 1/3 length darts at once haha

[@steeef54]

@@maritimefoam nice I put a k26 in a xshot Claw hunter, cut the dart posts and made it shoot both chambers at once it fits 4 half darts and has great spread similar to this

[@maritimefoam]

@@steeef54 that’s awesome. So fun to make actual foam firing shotguns!

[@lstudios3237]

sick video bro i want to do it but add shells that would be *EPIC*, oh and make full length thrifting videos i think it would be fun :)

[@eric3347]

Two half darts in a shell would be sweet, but what blaster would be best to start with? I thought all the shell ejecting shotguns were lower fps than the double fire.

[@maritimefoam]

The predecessor to this one did have shells, which is neat, but yes it was also lower FPS. I do like that this is just kinda simple. Though I did think about making quarter length darts and wrapping them in wax paper to load them ha. Just to be goofy. Not practical really :)

[@eric3347]

@@maritimefoam I'd watch that video. Can you make foam wadding and shoot some hyper rounds out of it? Do these mods need a spring upgrade if you get silly enough?

[@maritimefoam]

@@eric3347 ha, it probably would. It’s a very small plunger tube, and the spring is fairly stiff already though. Maybe a spacer

[@syndican_]

I tried this and i RUINED MY GUN, the boiling broke myplungers and they melted, it was not removing the orange ;-;, i saved up for that man, its 1000 pesos where i live ;-;

[@maritimefoam]

Sorry to hear that. Modding is definitely not without risk. :(

[@syndican_]

It sicks but its true, but i regret even trying it now, i had so much fun with it for 2 days, i had it for 2 days.

[@eric3347]

Looks like I need the smaller 1/4 inch sanding drum, glad I didn't open the blaster yet.

[@justpurestupinity401]

Can i just remove the prongs and leave the air restricter?

[@maritimefoam]

You can, but it won't fire as well :)

[@PlagueMaster815]

I had one of these for ~3 years and the first firing tube popped off, Sadly the spring that makes it fire (I believe the same one being talked about in a different more popular comment had fully broken, RIP a surprisingly good blaster. (Good thing its like 10 bucks to fet a new one!)

[@Giosuke_Giogashikata]

Are the springs strong enough to effectively take a brass barrel? Edit: Extra comment: You seem so darn happy, and it’s infectious. I have the smiling flu now. It can be cured with depressing whatever’s, but I DON’T WANNA!!!

[@RATKING199]

So...mine broke and I can't open it. Once I do, this video will be a big help due to the reassembly part

[@Saewich]

Where do you put the water? Do you just soak the piece in it or what, I’ve been at it for hours. If you could help me, I would appreciate it Thanks!!! Have a good day 😃

[@maritimefoam]

It’s a PAIN! I poured it over the areas with glue, over and over (I didn’t soak, was worried about warping, maybe didn’t need to be) and I used a plastic knife to try and force a gap as I poured between pours - it was not easy lol

[@Saewich]

Yeah I bet, I ended up breaking the gun so yeah. Loss of 13 bucks 😂

[@Pro_Bad_Influence]

how long do i need to soak the part in for?

[@maritimefoam]

I poured a kettle of water over it slowly, and then wiggled it gently and then poured another kettle over it. A plastic butter knife is a handy tool to use if a bit gives way. Just need to be very careful.

[@shikhasomwanshi]

Nice video! I tried to do this because my gun was only firing one, but now it won't fire at all. Any solutions? 😢

[@maritimefoam]

Sounds like an issue with the string? Perhaps 11 dollars at Walmart can fix it! Haha .

[@noeldecastro758]

Thanks for this video i fixed mine😅

[@maritimefoam]

Oh awesome!!! I always love hearing that!

[@trantuyetlan9910]

oh yeah

[@frogfromtwitch]

An inline clip mod would be cool

[@SemihU]

How am i suppose to boil them? I didnt understand

[@maritimefoam]

You pour boiling water over the parts that are glued, the hot water can soften the glue enough to carefully pull the parts apart. It’s a pain to do so for sure.

[@lrnzogaming]

Did you also have a problem with pulling the puley over that one peg? I feel like as I reassemble it more the pulley gets smaller 😭.

[@maritimefoam]

Ha, pretty sure I did.

[@HappyPult]

Does the string easily snap? because I saw a lot of reviews on the Walmart website saying the strings break after a few days of use

[@maritimefoam]

I dunno about easily, I’ve used one a bunch, and have thrifted a couple that worked, but it is a chord. You could also just replace the string! Good mod project for 10 bucks new I think still.

[@HappyPult]

@@maritimefoam oh alright!

[@IIsLazy]

How long should I soak it in boiling water? i've done it for about 20-30 minutes now and its still stuck on hard

[@maritimefoam]

Well, you kinda need to work it as you soak it, it’s a process… I tend to pour over the area that’s glued and wiggle. I’ll use nylon pry bars or plastic butter knives to get in any gaps if I can.

[@IIsLazy]

@@maritimefoam Thanks you! One more question though, how do I keep my hands not-burnt when the plastic is still hot

[@they2kguy822]

I think i accidently submerge the post plunger tube (the orange one) too much in the boiling water to the point it warped (and/or it melted the plastic to the welded glue?), what do I do?

[@maritimefoam]

Oh no! I poured water over it, I didn’t soak it :S

[@they2kguy822]

@@maritimefoam no I actually submerged it and put it for too long

[@Flooph_YT]

How long do you need to soak the tubule with the solvent on it?

[@Flooph_YT]

Nvm it broke, I’m going to try and glue it and use a hammer and screwdriver to get the orange thing out but I might just buy a new blaster if I need to. :(

[@jpegjared]

Have you tried the AF Cornerfire? It comes with two 10rd cylinders and you can look around corners with it. It has a really good trigger in my opinion.

[@maritimefoam]

I’ve almost bought that about… 700 times haha

[@jpegjared]

@@maritimefoam caved in and bought it after walking by it 701 times

[@frogfromtwitch]

This is the most frustrating thing to put back together

[@maritimefoam]

It’s not super fun

[@eric3347]

I was looking for a way to mod a double barrel nerf shotgun to put the dart in the other side without a shell. Do you know any way of doing this? Maybe cut the shell in half? I think your mod sounds more fun anyways. Looks like I'll be getting a double shot and a dremel soon.

[@maritimefoam]

Hmmm, yeah, I’m not sure. Yes, for the money I think this is worth doing and playing around with for sure. The solvent weld is a pain, but not that big a deal. I might do another one of these.

[@eric3347]

Yeah, I'm definitely making one of these after Christmas travel. I'm also starting to get tempted to load half darts into a shell ejecting shotgun, that would give the shell a reason to exist. Why do I want so many shotguns? Why can't I just have a spring thunder that shoots trilogy shells?

[@eric3347]

Ok, ignore the hyper idea. Those are bigger than nerf darts and airsoft BBs would bounce around inside the barrel too much. I'd still love to see how many 1/N darts you can fire out of this or a shell version.

[@maritimefoam]

@@eric3347 ha, it’s truly hard to find a use for Hyper… I kinda like the Rush 40 though. I would love to find a trilogy.

[@tur7743]

Can i replace springs?

[@maritimefoam]

I think it might be a bit delicate inside to beef up too much

[@GrotleForNow]

Im a bit fixated on this idea too and would like to try it.. however I wouldnt know what spring would be able to replace it... or i get another Double Fire and just double up on the springs?

[@Turtleboilol]

If it didn’t have the string, would it still work?

[@maritimefoam]

Well, the string is needed to prime it, so, not really I’m afraid

[@Turtleboilol]

@@maritimefoam mine’s not broken I’m just wondering If the string was broken, would it be easily replaceable?

[@FronkStronk]

​@@Turtleboilolas long as the string is the same length I don't see why it would be hard.

[@Turtleboilol]

@@maritimefoam It’s been a while, say, is it normal for my left dart to pop out the left barrel when I try to prime the gun? It still works pretty much fine, but the left shot is a little smoother than the right shot.

[@souaadbenmeziane4331]

It didn't work for me

[@maritimefoam]

What part?

[@CratereRime7898]

Bro his head was in tge way tge whole time and I couldn't see anything.

[@maritimefoam]

The whole time huh? You’re welcome for the free video to try and mod your blaster. Plenty of people have used it to help themselves. Still requires effort and some learning though.

[@CratereRime7898]

@@maritimefoam i threw it away👍. But im planning on buyimg a new one tho.

[@thefinalshape333]

hey i got that gun