Airbrush Miniature Painting Tips I WISH SOMEONE TOLD ME

  Рет қаралды 580,468

Lyla Mev - The Mini Witch

Lyla Mev - The Mini Witch

Күн бұрын

Пікірлер: 531
@LylaMev
@LylaMev 2 жыл бұрын
What has been your biggest airbrush fail?
@WildWilly292
@WildWilly292 2 жыл бұрын
Not realizing I had super thick dry tip. I was slowly pulling back the trigger and nothing was coming out, so I kept pulling. Eventually I guess the gap was big enough that it blew past the dry tip and coated my mini in a thick blob 😂
@tinyfishhobby3138
@tinyfishhobby3138 2 жыл бұрын
Dropping the airbrush and bending the needle. That was a $15 replacement.
@profaa927
@profaa927 2 жыл бұрын
Pulling out the needle with paint still inside..... I think that there is nothing wrong with it after some cleaning but im still traumatized.
@shovah85
@shovah85 2 жыл бұрын
I appreciate you. You are making videos that seem tailored to the exact questions that I am trying to answer write now. Trying to get gud at painting.
@RerollingOnes
@RerollingOnes 2 жыл бұрын
I leave the back off of mine so I have quick access to the chuck and needle, so I can draw it back while rinsing between colors. My cat has pulled it down to the floor twice, where it landed on the needle and jammed the needle through the tip, split like a bannana peel. The tips are brass, and relatively soft. RIP airbrush tips.
@ajosepi1976
@ajosepi1976 2 жыл бұрын
I have been airbrushing 30+ years and 7 were professional on motorcycles, and cars. Everything in this video is correct, but as you progress you will find exceptions to some of what is in this video, and you can get away with more things as skill progresses. So this is a VERY GOOD starting point! Good job! To tighten your edge work, practice by painting a grid of dots, connect those dots with lines as thin as possible. Then like with the circles paint gradients from bottom to top, left to right, top to bottom, right to left, diagonal from each direction, and so on. Use the angle of the tool to get a crisp line on the dark side of the gradient. Replace your smooth caps with crown caps or take a rotatory tool or file to cut slots in the cap. When you get the airbrush close to the object you get a backwash of air into the cap and this disrupts the paint spray pattern. A crown cap will allow that backwash to mostly go around the tool. You can also remove the cap for tight work, but you run the risk of damaging the needle. 0.2 mm Needle can do hair lines, but 1.5 mm makes that easier at the cost of lower max volume. You can pretty much do everything with a 0.2 with practice. I think playing with air pressure is something people need to do more. If you are getting "pulsing" in your paint from the compressor, get a tank in line and or a disposable air filter. You will need to up the pressure a bit for the filter. This is normal. If you are getting water in your line, get a long hose from the compressor and put the tank or filter on the end of that. 25 feet is what I used, but you may need longer or shorter depending on what your air is like where you are. This allows the air to cool before it gets to the airbrush and will condense in the filter or tank. If you get a tank, CLEAN it every day. Also if your compressor can not push enough air in a long line, use an ice pack on a shorter line, or just a cold wet cloth. You need the air cooler in the line before the filter so it will be water and not wet air. There are a lot of simple cheap tricks to getting good air. My best setup at home was, air compressor with built in tank, 25 foot of airline, small tank, filter, regulator, airbrush hose, then airbrush. This is not needed in most cases, but gives you great clean consistent air. There are a LOT of ways to do this. Mine works for me, but that doesn't mean it is right for everyone. The only thing that is 100% right for everyone in every situation is practice, practice, practice! Sorry for the novel. I just have a lot of experience in this area.
@voDKaandEric
@voDKaandEric 2 жыл бұрын
What that guy said.. lol.. same here. great job
@theophrastusbombastus1359
@theophrastusbombastus1359 2 жыл бұрын
I'm sure there are many helpful tips in there but I'm not combing through it. But if you ever decide to use paragraphs in future I'll be sure to read it thoroughly
@ajosepi1976
@ajosepi1976 2 жыл бұрын
@@theophrastusbombastus1359 Welcome to the internet. Good luck! 🤣🤣🤣
@MonteKowalsky
@MonteKowalsky 2 жыл бұрын
I’ve never had a chance to really play with an airbrush, so I was really curious what ways there are to mitigate water in the line, so this advice is awesome. Using something cold to condense the moisture is something I never would have thought of on my own. My experience with compressors is in a carpentry context and while annoying, water in the line isn’t the end of the world there. Well, fine finish work notwithstanding. But some (probably slightly rusty/oily) water splatter out of your nail gun is one thing; the idea of rust and oil through an airbrush makes my heart hurt and I don’t even own one. Regularity draining the tank on a compressor that has one is also a very important safety measure. The temperature differential *will* produce moisture in the tank which left unattended will rust out the inside. Thinning walls on a pressure vessel is, to put it lightly, a bad thing. And if you’re embarking on a painting marathon lasting all day, drain the tank once or twice throughout the session, depending on the ambient temperature.
@YTiswoke
@YTiswoke 2 жыл бұрын
I appreciate your novel ! More is better when it comes to pro tips.....i recognize and respect your experience.....thank you
@Sundaydish1
@Sundaydish1 Жыл бұрын
FINALLY! Someone that actually explained the airbrush properly. I have watched dozens of "Airbrush Tip" videos and all they talk about is paint! Grrrr.
@pebblesthecat3625
@pebblesthecat3625 2 жыл бұрын
Thanks for this video. My husband very kindly bought me an airbrush set up for my birthday 2 years ago. I took it out, checked everything was there, and put it away. The fear of messing things up stopped me from even trying it out, but after seeing this video, it doesn't seem as daunting as it first did, so I'm going to try and learn how to use it. Thanks.
@raytheron
@raytheron 2 жыл бұрын
Great video! Thanks for sharing your experiences! One thing I stopped doing a while ago is to pull the needle out to the back while cleaning it. Instead I remove the nozzle and push the needle through the front of the airbrush. That way you don't drag paint onto the seals and don't risk damaging the needle tip, especially with smaller sized needles. I clean the whole needle of any paint it comes out the front with, and repeat until the needle comes out spotless. Every few months or so, depending on how often I use the airbrush, I put it in my ultrasonic cleaner to get rid of any hidden gunk. It always works a charm!
@stevenborman9110
@stevenborman9110 2 жыл бұрын
I have a small dish and a sponge that I keep damp with water and every so often press my airbrush into the sponge and pull the needle in and out, I find this is better to get rid of tip dry. Get yourself some interdental brushes as they are far better for cleaning your brush than what I saw (desigend for your mouth, so less chance of damaging your brush) also, pipe cleaners, not the craft ones as they lose fibres. Use laquer thinners for cleaning, and a final blast of expensive airbrush cleaner when finished. Your points on practice and paint mixes was so spot on, especially with acylics :)
@LylaMev
@LylaMev 2 жыл бұрын
Thanks for the ideas!
@NikkiAnnMarie
@NikkiAnnMarie 2 жыл бұрын
Just as general advice, be careful with lacquer/cellulose thinners - make sure your airbrush has seals that are resistant to it (teflon/PTFE), otherwise it can ruin them. Most of the more expensive airbrushes have this, but the cheaper Chinese ones tend not to
@TheRedmagma1
@TheRedmagma1 2 жыл бұрын
Oh my god, this advice has been an absolute time-saver. Thanks for the advice
@sirrathersplendid4825
@sirrathersplendid4825 Жыл бұрын
@@NikkiAnnMarie- Yes. Made the mistake of tearing down my cheapo Chinese brush and rinsing the o-rings in airbrush cleaner. They turned spongey within minutes and would have dissolved completely if left to soak. Quickly rinsed them off and they appear to have almost reverted back to shape. There was, however, a single tiny o-ring deeper within the brush which may have been teflon, which came loose during cleaning. It sprung off onto the floor during reassembly, never to be seen again.
@tinyfishhobby3138
@tinyfishhobby3138 2 жыл бұрын
Love my airbrush! That bit about ignoring your advice if it doesn’t work is spot on. Every airbrush and batch of paint is going to be different, and often it’s just a matter of experimenting until you find what works for you.
@LylaMev
@LylaMev 2 жыл бұрын
I tried for hours on my old brush trying to get 30psi to work with no success. I finally figured out I needed to use my brush at 60psi to get good flow. In the process of shooting this video, I learned that my hose was cracked at one end the WHOLE TIME and that's why I could never get it to work at 30!
@thomasjones3221
@thomasjones3221 2 жыл бұрын
@@LylaMev what brand of hose?
@tinyfishhobby3138
@tinyfishhobby3138 2 жыл бұрын
@@LylaMev Mine is basically always set at 25psi and that seems to work for everything for me, but I can see how having a cracked hose would wreak havoc with any airbrushing and pressure you’re trying to get. 😩
@KitBasher1
@KitBasher1 2 жыл бұрын
5:41 I used to have a nice pashe? Dual action airbrush… thinking about getting a new airbrush station - awesome video!
@marksminis
@marksminis 2 жыл бұрын
I got the cleaning down to 3 min. The trick is to fully clean and flush out the cup before anything else. I use a water squirt bottle to blast out the paint and one swab to mop it good. Get the cup totally shiny clean! Then proceed with the rest of the cleaning, which goes really fast. A couple blasts of cleaner and a mop of the tip usually finishes it.
@mikeuziel
@mikeuziel 2 жыл бұрын
Great video! One other alternative with the needle--- Push it through from back to front and pull it out that way. Aside from not dragging paint through the airbrush, you also don't run the risk of getting a burr on the tip when you reinsert it. :)
@thylange
@thylange 2 жыл бұрын
In order to push the needle out in front, you have to remove the nozzle. This means that there is a risk of damaging the nozzle. After ruining two nozzles, i now am very careful with the nozzle. In many cases you dont need to remove the nozzle and this reduces any risk of damage.
@animalyze7120
@animalyze7120 2 жыл бұрын
@@thylange Wrong, no damage to the nozzle will occur unless you over tightened it already. Either direction is fine as long as you take care and the Needle is far more costly than the nozzle.
@thylange
@thylange 2 жыл бұрын
@@animalyze7120 In my local shop nozzles are more expensive. Needle: 159 SEK. Nozzle: 410 SEK, more than twice as expensive. Anytime you remove the nozzle, there is always risk of damage (I did not over tightened it). I learned that most of the time you don't need to remove the nozzle to clean the airbrush. Most of the time i do a quick cleaning without removing the nozzle. And then i occasionally do a more extensive cleaning. I been using airbrushes for 12 years.
@YanniCooper
@YanniCooper 2 жыл бұрын
If you use contrast or speed paints, I highly recommend mixing up a large batch of your favorite base prime color. I've used an old 200ml bottle to mix up something that's pretty close to Wraithbone. Mostly white primer w/ a little bit of brown and yellow mixed in, and enough airbrush flow aide that I can just pour straight from the bottle into the airbrush cup and since it's in such a large quantity I don't have to mix a new batch every time I'm priming new models yet I can maintain consistency easily between projects (and if I need to do touchups later I can always put a few drops on my palette )
@AndrevwZA
@AndrevwZA 2 жыл бұрын
Very detailed info. Great job. The only thing I saw you did and I would definitely advise against doing it, is in the end of the video where you used that metal core brush to clean the front of the gun. With guns with floating nozzles like the Iwata Eclipse range and Badger 105 range, the nozzle seating area is very important. It is soft brass and that brush has a hard steel core. If you scratch the brass, you will not get a good seal with the nozzle and you will get bubbles in your cup. You will have to use sealant if you want a good seal again.
@chadpatrick5112
@chadpatrick5112 2 жыл бұрын
Thanks!
@mattdeeley4302
@mattdeeley4302 2 жыл бұрын
Had an airbrush for over a year. Follow many of the popular mini painting channels, this is the best, most consice airbrush beginner tutorial I have seen so far. Thank you lyla! You rock 💕
@LylaMev
@LylaMev 2 жыл бұрын
I'm so glad I can help!
@m.maclellan7147
@m.maclellan7147 2 жыл бұрын
Definitely the best cleaning tutorial ! I had one years ago buy it got ruined due to not cleaning it well enough !
@Gorillasecret
@Gorillasecret 2 жыл бұрын
I love how concise and quick your instructions are. Really appreciate you making this video it helped me a lot!
@philbrown8181
@philbrown8181 9 ай бұрын
Probably the best guide I've seen. Simple, succinct and clear. Thanks for making and posting.
@georgewilson5303
@georgewilson5303 2 жыл бұрын
I have never airbrushed. I am getting my first one. I am so glade to have came across your videos. This helps me feel a little easier. My son is the number one airbrushing artist in the state of florida. He started at 12 years old. He never went to any school for any. He is self taught. He paints 3d and taught himself how. Harley davidson sends him jobs they want done on certain bikes. He lives in florida and I am in Tennessee. He helps as much as he can. But between his work and the distance it hard. So I appreciate your time and knowledge you give. Thank you very much. Stay safe and happy. I have just subscribed
@dianemarieevans9145
@dianemarieevans9145 Жыл бұрын
Thank you so much. I Just received my new Airbrush & excited to get started. I'm 68 years old & trying something new. I could understand your video well. Thank you. 😊
@ElPrezAU
@ElPrezAU 2 жыл бұрын
Great video for airbrushing neophytes. The only thing I'd add that I think is important for new airbrush users to learn is that there are three factors (assuming equal air pressure) which determine paint flow - the trigger and distance (as shown in this video) but also how far down you push the trigger. When you start it feels as though it's a binary equation, either you are pushing down and making air come out or you aren't and air isn't. But even though the range of movement is tiny, over time you can learn to control air flow by how hard you press down on the trigger. This is super helpful when glazing small areas or doing other fine work. That said, I'd suggest to airbrush users to get comfortable with all the other aspects first, but to still keep this in the back of your mind as you do.
@captin3149
@captin3149 2 жыл бұрын
Just looking into it and learning before I buy one, but is what you're talking about a double action airbrush? It was my understanding that single action airbrushes can only have the trigger pulled back, not pressed down as well.I'm trying to learn everything I can before buying.
@LylaMev
@LylaMev 2 жыл бұрын
Yes, he is talking about a double action airbrush, which is also what I use for my own painting.
@vee_tinymoose
@vee_tinymoose 2 жыл бұрын
Thank you!! I’d seen people do back blowing but I hadn’t realised to clean the needle first. Anytime I’ve tried backblowing it’s just clogged my airbrush up. Now I think I understand why!!
@claudenewbolt2659
@claudenewbolt2659 2 жыл бұрын
I'VE SEEN TWO OF YOUR PROGRAMS, AND YOU SOLVED SOME OF THE PROBLEMS I WAS HAVING WITH MY AIRBRUSH!
@damianchenot2667
@damianchenot2667 2 жыл бұрын
I'm glad to see the Paasche Talon airbrush in your video. That's the one I personally use and really enjoy it. It seems like many channels drive new airbrush users straight to the Iwata Eclipse or Harder and Steenbeck models. There are plenty of affordable and good quality brushes out there that suit our purposes well for a fraction of the price. The Talon is one of those brushes!
@voDKaandEric
@voDKaandEric 2 жыл бұрын
I am an Iwata fan. I do it for a living and I do like them, but eBay has a Master series, multible tips and needles Iwata knock-off that actually works REALLY well for the 35~ buy-in. Solvent proof as well.
@AlexEding
@AlexEding Жыл бұрын
Expanding on Lyla's cleaning tips for new airbrushers: Learn how to clean and maintain that airbrush. Know where your brushes' trouble spots are, as well as how to really get in there and clean out the needle nozzle if you get buildup. I'm a big fan of LA's Totally Awesome (I learned this from Goobertown Hobbies) to do a deep clean on my brush parts (and for stripping minis) that are allowed to be wet. I even have a cheap sonic cleaner to help with this.
@jimspc07
@jimspc07 Жыл бұрын
One of the best advice on airbrushing I have seen after 2 weeks solid of trying to get the hang of airbrushing.
@stevemurzin2274
@stevemurzin2274 2 жыл бұрын
Very informative. I was wondering if there are any tips to save time when switching between colors.
@glennrobbins2372
@glennrobbins2372 2 жыл бұрын
Great video. I am still learning how to use my airbrushes and this helps. A tip to share that I use to clean my needles is using alcohol prep pads if you are using acrylics like I do. One of my brushes was used and gifted to me by the person I bought a compressor from. It was caked with metallic paint but I gave it a thorough cleaning. Now I am going to check it to see if it has the trigger stop.
@HouseDM
@HouseDM 2 жыл бұрын
Thanks Lyla! Been considering diving into the world of airbrushing and this vid was super helpful. Cheers!
@robloseby3631
@robloseby3631 2 жыл бұрын
Thanks as the title goes I wish someone had told me. Thanks for putting me right. I really like the tips for cleaning the needle and the use of a paint brush to help clean it.
@SC2Anski
@SC2Anski 2 жыл бұрын
One thing I like to do when not painting for display is to first brush on really over the top dark shadows + highlights then go over with an airbrush to change the color to what I want it to be. This also blends the mid tone shadow and highlight very nicely. Very nice when you just want to paint something nice and quick. I usually go back with a brush to add texture afterwards tho..
@davidlanier2290
@davidlanier2290 2 күн бұрын
Thank you.been debating airbrush... is a logical progression for me but i don't know anyone that has one.
@maizetoken377
@maizetoken377 Жыл бұрын
Thanks for this video! Great tips. Love the editing as well. Just got an airbrush (used it twice), and this video resolved many of the questions I had. I especially liked the tip of using the airbrush to blend blocked-in colors painted by hand. Seems much faster than glazing!
@prehanramsamy6728
@prehanramsamy6728 2 жыл бұрын
I am new to air brushing. My air brush kit arrived this morning. I watched your videos and kept in mind what you mentioned. Thank you for the effort and time you put into this video. It really helped a lot. If there are any other tips you have it would be appreciated.
@Rich-in6ds
@Rich-in6ds Ай бұрын
Thanks for this. Very helpful. I’ve just started and am trying to base coat dark purple over black prime and it has been a challenge. Really hard to see when paint is coming out and then suddenly BAM, too much paint and it’s pushing around on the model.
@ryo86ok
@ryo86ok 2 жыл бұрын
Great video!| 6:50 in most airbrush models, you should also get the corresponding nozzle cap. The aperture sizes are different, changing the size of the "air stream" coming out.
@MKotnis
@MKotnis Жыл бұрын
was skeptical of title, but, it's not clickbait, actually just a lot of good points
@Pijawek
@Pijawek 2 жыл бұрын
THANK YOU! Just getting back to the hobby and I have insane problems with using an airbrush. I used it with Humbrol enamels before, but now I want to use acrylics - since they don't stink - and re-learning was a nightmare. Your videos did help a lot!
@jaymaxwell8645
@jaymaxwell8645 Жыл бұрын
I appreciate the shots of you in the protective mask. It's a good reminder.
@-Garviel_Loken-
@-Garviel_Loken- 2 жыл бұрын
You should try one of those sonic cleaners. When I took commercial art in school we’d disassemble our airbrushes and run them through the sonic cleaner. It works wonder, especially if you have dry paint
@LylaMev
@LylaMev 2 жыл бұрын
Thank you!
@funchick202
@funchick202 2 жыл бұрын
Those sonic things are the best
@1pcfred
@1pcfred 2 жыл бұрын
What cleaning solution did you use?
@-Garviel_Loken-
@-Garviel_Loken- 2 жыл бұрын
@@1pcfred I’m pretty sure we just used water.
@1pcfred
@1pcfred 2 жыл бұрын
@@-Garviel_Loken- just water would work with water soluble paint.
@mrsaizo0000
@mrsaizo0000 2 жыл бұрын
That's why I adjust and test before applying color to my models (Harder & Steenbeck). Also, get a compressor with a "reservoire" (air tank)..
@jasont2610
@jasont2610 2 жыл бұрын
Great video.- Ill be looking out for more of your videos - I've sub'd. One thing though: I think thicker and thinner lines is actually most influenced to how far you hold the tip of the brush from the work. I thinkneven in the video the thinner lines ere done with the brush much closer to the work and the wide example the brush was held farther back. Essentialt the paint comes out as a cone, with the point of the cone near the brush tiop and the base of the cone on the work. The closer the brush, the narrower the base of the cone. The needle size is more about what type of paint you are using. Some paints have finer pigement/thiner consitency e.g. ink or laquer based paints and you can use a finer needle with those, while other paints e.g. acrlyics work better with a larger needle.
@aliekoffeman6194
@aliekoffeman6194 2 жыл бұрын
I always take apart my airbrush after each session and clean the inside of the body, needle and nozzle separately. When storing my airbrush I always pull back the needle just a little. When airbrushing, I lay my finger flat on the trigger. That way it's much harder to fully pull back the trigger all the way and it forces me to use small motions. Though I mostly use the HS Infinity (that comes with the option to regulate how far you can pull back the trigger) I never had to use that function by keeping my finger as flat as possible. This does result in finger cramps at first but goes away with practice 😉 After a few years of airbrushing on paper, I want to make the switch to airbrushing miniatures. I found out it's quite a different beast!
@sillymonger
@sillymonger 2 жыл бұрын
This was the best practical video on getting started with an airbrush. Seriously great work, thanks Mini Witch!
@chaoticpainting1507
@chaoticpainting1507 2 жыл бұрын
Lyla, you're awesome! Thanks for the tips, that will certainly have value for beginners! I've had my airbrush for a few years but still found a few things in this video that will help me out! 🤘🏼
@LylaMev
@LylaMev 2 жыл бұрын
I'm glad!
@ernstbergerbrent
@ernstbergerbrent 2 жыл бұрын
I discovered your channel a few weeks ago. You have breif and informative videos. I don't have to skip through to get to the important parts. Thank you for the content.
@andrewdodd1918
@andrewdodd1918 2 жыл бұрын
I found using a Rigger for comics and daily exercise with a hand grip helped me do two things with the airbrush. The first was changing the thickness of the line from thick to thin during one stroke and the second was being able to paint for long periods with hand strain. It can get a little tough when doing a large piece and this helped me.
@cerhart7172
@cerhart7172 2 жыл бұрын
I'm just getting back into airbrushing after a very long hiatus, so this is a timely refresher - thank you! Probably going to go through a lot of paint while practicing and getting my touch back before I trust myself on minis again. ^_^
@LylaMev
@LylaMev 2 жыл бұрын
I'm happy I can help you!
@DamenBrooks
@DamenBrooks 10 ай бұрын
This video is really good. I like the practice methods and PSI debug info.
@dialupsyndrome1910
@dialupsyndrome1910 2 жыл бұрын
Not sure if it's the same with all airburshes, but with mine I can push the needle out through the front of the gun, this prevents paint being pulled into the body on extraction.
@AtomicVic
@AtomicVic 2 жыл бұрын
Was looking for this comment! It`s exactly what i do with mine too.
@LylaMev
@LylaMev 2 жыл бұрын
Thanks for the tip!
@dialupsyndrome1910
@dialupsyndrome1910 2 жыл бұрын
@@LylaMev you're welcome :) and thank you too for all of yours
@WrenintheRoses
@WrenintheRoses 2 жыл бұрын
Your video was very informative and has filled me with excitement for the fun and frustration that is to come. I’m returning to airbrushing after a very long break. I’m going at this like I’ve never seen an airbrush and this was the first of your videos I’ve seen. I’ve subscribed to your channel and I definitely liked the video. I’m building my setup around an 8 gallon air compressor given to me by a friend and components I can find at discount stores, on sale and online. Mostly, I want to create custom artwork for the prosthetics worn by amputees like myself. I have a 25 year career as a professional tattoo artist to call on for inspiration. And, the basic techniques of airbrushing and tattooing are very similar.
@randallguidry3624
@randallguidry3624 2 жыл бұрын
Thank you for another reminder and encouragement to keep trying with the airbrush! Already feeling more confident and having success!
@sebastianrubio928
@sebastianrubio928 2 жыл бұрын
Excellent video, I think it's very useful, I've been airbrushing for a couple of months now, I still consider myself a beginner, cause I still make noob mistakes. As good as the video is, I look at tutorials differently than I used to, simply based on the new experience I've got. I did notice 2 things to try out next session (cleaning stuff), clearly I still got a lot to learn. I got to the point where I used my 60 euro beginner's airbrush enough and it's time to move to something better, I got a badger patriot as a starter to a more serious airbrush and once I got a bit more experience I'll get the next one. I still prefer brush painting, i'm doing mostly warhammer stuff, the scale is just too small, though the airbrush saves insane amount of time on those base layers. Doing a few base layers on several minis has been great practise to slowly delve into details. I see what a cheap airbrush does, I want a smoother experience at this point. I have been watch & rewatching youtube tutorials on airbrushing. I went for the patriot cause so many are using it, the Iwata Eclipse was a close second place, I might still get it later, I see so many people swear by their Eclipse. I'm also pretty interested in the H & S Infinity and the Badger Sotar, but both are used for more detailed work, for now I'm sticking to base layers and base blending. When I'm confident enough, then only will I move to the details with airbrush. I am hoping the clogging will be solved at least in part, my compressor also overheats, it's only of those tiny beginner ones, thnakfully I got a good serious replacement arriving soon.
@fotomakr
@fotomakr 2 жыл бұрын
The cleaning tips at the end! The keep your airbrush happy bonus.
@phrixos2826
@phrixos2826 2 жыл бұрын
Thank you for these tips lass, I have yet to get my first air brush, i am looking forward to getting into this way of painting, and these handy tips wil help! EXCELENT VIDEO
@WildWilly292
@WildWilly292 2 жыл бұрын
Omg perfect timing - just got my airbrush. So excited to put it to good use
@LylaMev
@LylaMev 2 жыл бұрын
Have fun!
@haden636
@haden636 2 жыл бұрын
I was actually thinking about getting into air brushing so I'm glad I ran into this video first.
@a.gnailz
@a.gnailz Жыл бұрын
I just tried an airbrush on nails and I had all these problems thanks great video!!
@josephpatton8869
@josephpatton8869 2 жыл бұрын
Thanks for this! I am so on the fence of crossing the airbrush rubicon. This might be the final nudge! 👏
@psyberwolfe
@psyberwolfe 2 жыл бұрын
Hey we both use the Paasche Talon. How cool is that! I see so many use other brushes so it's cool when I see other Paasche miniature painters.
@sleestack2723
@sleestack2723 2 жыл бұрын
NEW LYLA VIDS LETS GOOOOOOOOO and again on point with what I’m scared of!
@LylaMev
@LylaMev 2 жыл бұрын
Thank you!
@erallen97
@erallen97 2 жыл бұрын
Great video! I'm just getting ready to try an airbrush for the first time.
@garycarver3694
@garycarver3694 2 жыл бұрын
You did a pretty good job at explaining that I've been there brushing since late 97 98 and I've also taught airbrushing and I went several years not airbrushing and I had to start all over again and retrain myself and I did it you know the same way it was back when I first airbrushed there wasn't no internet thing that I could go to I learned by reading books and watching other airbrush artist but I really appreciate what you're doing to help people understand may the living God Jesus Christ bless you and your endeavor to try to help people learn this wonderful skill
@johninnaperville
@johninnaperville 2 жыл бұрын
One trick I saw on another channel for cleaning the airbrush is to have a bucket of water around. Dump any excess paint and then put the airbrush in the water and place your finger alternating on and off the tip to flush and back flush the gun until the water coming out of it is clear. This works exceedingly well in cleaning the brush.
@douglaspearce9677
@douglaspearce9677 2 жыл бұрын
thank you for the refresher in the prosses of getting everything i need
@sadev101
@sadev101 2 жыл бұрын
have about a dozen airbrushes.. even though trigger pulling ones are more versitiles but when i do model painting i prefer a non trigger airbrush.. i set the widh and then the airpressure and press full on... no mistakes
@peterplantec7911
@peterplantec7911 Жыл бұрын
I’ve watched several of your videos and they are helpful. Thank you.
@majorredbeard
@majorredbeard 9 ай бұрын
Thanks for the tips! I haven't yet started but I'm looking to dip my toes into airbrushing for a costume that I'm starting to make.
@AllensTrains
@AllensTrains 2 жыл бұрын
Helpful video for those contemplating getting an airbrush. Thanks for uploading.
@stephenullman4534
@stephenullman4534 2 жыл бұрын
Really great tips! Thank you! You saved an old man some aggravation. I'm just learning how to use this crazy thing. You helped a lot!
@madhatter38m
@madhatter38m 2 жыл бұрын
Crazy doesn't begin to describe it. It's like playing golf, an exercise in frustration.
@Waterratt4344
@Waterratt4344 2 жыл бұрын
Thanks for the video, very informative, I’ve had some good results with my airbrush, but I will be using your tops! Thanks!!
@MestreGuilderiusLCB
@MestreGuilderiusLCB 2 жыл бұрын
Thank you very much Lyla, you're helping so much ! I'm starting my long journey of airbrush learning, and while I struggle with finding the right ratio dilution/psi, your video just made me realize my gun as a stop on its back 🤯🤯🤯 This will help so much :D
@owntor1
@owntor1 2 жыл бұрын
6:56 Can't back flushing sometimes force paint past the needle bearings?
@joshuagoss6896
@joshuagoss6896 2 жыл бұрын
Hey there! Really good tips, but I have one for you. Instead of pulling our needle out from the back, push it out the front. Clean the paint cup, backflow, etc. just like you showed, but leave the needle alone. Unscrew and remove your nozzle, then loosen your needle and push it to the front, grab it now that you have room, and pull it out from the nozzle end. It keeps any paint that may still be in the working part of the airbrush from being drawn through the seal, trigger and spring housing. This helps to keep the back side of your airbrush super clean. Keep up the good videos!
@MrTripletts
@MrTripletts 2 жыл бұрын
Im not taking that nozzle out any more than i have to
@ARescueToaster
@ARescueToaster 2 жыл бұрын
Regarding air pressure / PSI when airbrushing: There are so many variables to it - the only thing you can get is a general idea of where you'd want your PSI (usually 20-40 PSI range). But it depends on many factors. Factors like what paints you use, how thick your paints are, your airbrush, your compressor, your needle, how clean your airbrush is, your elevation (how high you are above sea level), etc. etc. The only way you can know for sure is by experimenting yourself, which you should be doing already! Just have fun with the learning experience and it will go quick
@StephanBeal
@StephanBeal 2 жыл бұрын
1:55 the problem with such "stoppers" is they keep you from doing periodic bursts to keep the nozzle clear. i remove those stoppers from my brushes for that reason.
@pauljs75
@pauljs75 2 жыл бұрын
I wonder if masking fluid is worth a mention? Doesn't that give more control for details like a regular paint brush, but allow you to take advantage of the airbrush for blending and area coverage?
@mccarvillestudios
@mccarvillestudios 2 жыл бұрын
Huge thanks for the tips. I think I will watch this again now!
@stevecam724
@stevecam724 2 жыл бұрын
Thanks for sharing 😊👍 Biggest fails are to much/to little paint 😢😢😢
@xtcaudio
@xtcaudio 2 жыл бұрын
Do you have a video showing how to airbrush straight/fine lines? An example would be like a piece of clothing. I always have trouble with one color getting on a part of the figure I don’t want it (like the shirt is blue and it gets on the tan skin, or the tan gets on the blue…just an endless cycle of one color getting on another). I’ve been using clay and liquid rubber to cover parts I don’t want paint to get on but it either peels off the paint beneath it or doesn’t cover exactly where I need it to. Taping off a figure is just as hard because it doesn’t work on curves, uneven surfaces, or tight spaces.
@jrsantoyo9028
@jrsantoyo9028 2 жыл бұрын
Awesome video. I tend to forget that air brushing takes patience I have the spray can mentality.... I just wanna throw paint in and spray hahaha. Thank for this video.
@sukhrobmirzodavlatov2385
@sukhrobmirzodavlatov2385 2 жыл бұрын
This video poped up just in time. Bought my first airbrush and waiting for it to be delivered
@vincemincevince
@vincemincevince Жыл бұрын
that’s a great tip with blending where you hand paint first then blend it together
@Lucky-fj5qw
@Lucky-fj5qw 2 жыл бұрын
This was a great help I'm I'm just starting out never used an airbrush before and to be honest. I have not got a clue what I'm doing.. But this video was great Thank you 🏴󠁧󠁢󠁥󠁮󠁧󠁿
@madaxe606
@madaxe606 2 жыл бұрын
Super helpful for a beginner. Thank very much for uploading this.
@bigdenopaints
@bigdenopaints 2 жыл бұрын
This is excellent content, helping to demystify the airbrush for beginners. Thanks for making it!
@PeterAgostiniJdcap26
@PeterAgostiniJdcap26 Жыл бұрын
Great overview watching this one more till it sinks in . Thank you
@3DPrintedProject
@3DPrintedProject 7 ай бұрын
Thank you Lyla, just got into airbrushing, very helpful :)
@Lurch1031
@Lurch1031 2 жыл бұрын
Excellent video and perfect timing, I was gonna try my hand at airbrushing today
@LylaMev
@LylaMev 2 жыл бұрын
Good luck!
@lyleslaton3086
@lyleslaton3086 2 жыл бұрын
I wish you had been around 35 years ago. I started with a Badger 150, single action brush. True to your statement, i learned to with what I had. Practice is still what I tell people is the most important part. I'm Lyle BTW . Thanks for sharing this video.
@LylaMev
@LylaMev 2 жыл бұрын
I'm only 30 years old! 😅
@whiskypops
@whiskypops 2 жыл бұрын
Nice tips . I like tamiya paints no need for primers only on metal s
@Googaliemoogalie
@Googaliemoogalie 2 жыл бұрын
I have the same mask I use it for woodworking. But the carbon filters (3m filter 60922) would be better for paint because it has carbon in it to absorb fumes from paint and it also has the same p100 filter for particles. That's what you need!
@LylaMev
@LylaMev 2 жыл бұрын
I actually just bought a new mask yesterday!
@stevebrooks1304
@stevebrooks1304 2 жыл бұрын
Hi Lyla another great video , can I ask you what spray ,gun you were using please.
@LylaMev
@LylaMev 2 жыл бұрын
Check my description!
@rpals5412
@rpals5412 2 жыл бұрын
Hey there! I bought an airbrush setup little more than a year ago. And I have only used it like 5 times since, although I find it quite easy and the results very impressive... Main reason being that I do not have the patience for cleaning it more than painting with it. And I really have been struggling finding a way to quickly shift from one colour to another, and quickly clean up the gun, or keep it clean in general... I feel like it clogs up very easily, and the paint dries very fast if I hold a small break :( could you do a video with tips against these pitfalls ? that would be AWESOME! :)
@funchick202
@funchick202 2 жыл бұрын
I've never seen the stopper. I'll check it out!
@owenparry5000
@owenparry5000 Жыл бұрын
Great video, useful for new painters. Thanks.
@whittaker007
@whittaker007 2 жыл бұрын
Genuine question: what's with the shaking of the brush while painting? I've seen a few airbrush artists do it but not a single airbrushing tutorial has mentioned it. It seems like it's unnecessarily increasing the difficulty of applying paint precisely if you're shaking the brush around. I'm guessing it's maybe to avoid paint splatter for that first spray, like when you start spraying a rattle can where you want to start and end a stroke off the model to get an even coverage, but when you're airbrushing detail work you have to start on the model. So I guess shaking might help reduce splatter, but at the cost of accuracy. I can't help but feel that a steady hand and precise trigger control, starting with a light application of initial paint would be a better technique to use, but Angel Giraldez does it too, and he's an airbrush master. But nobody ever mentions it.
@LylaMev
@LylaMev 2 жыл бұрын
You keep the brush moving to allow the paint to dry. Even after the proper pressure, you can still cause paint to spider web if you don't let it dry.
@michaelgoodwin5510
@michaelgoodwin5510 2 жыл бұрын
Have a question: Could I use the Luminess brand air brush system (make-up based air brush system)? And how do I go about mixing oils for airbrush or is air brushing only an acrylic technique?
@sacpig6839
@sacpig6839 2 жыл бұрын
PSI is another factor and a big one. Some paints require an upwards of 40PSI, while others spray just fine at 7. Learning the personality of the colors was one of the roughest parts to me.
@Monstah7
@Monstah7 2 жыл бұрын
Thank you for your vids mate, they're simply the best airbrush guides for us noobs.. i for one really appreciate it..👍
@catlady8324
@catlady8324 Жыл бұрын
I like those glasses. They’re retro, but not too old fashioned. 👓 🤓
@TheScreamingFrog916
@TheScreamingFrog916 2 жыл бұрын
I use cotton tipped swabs (Q-Tips), to clean my bowl, because I can put more pressure on them, to wipe off old paint, than with a paint brush.
2 Miniature Paint brands you MUST TRY (And 2 to skip) | Pro Acryl, War Colours +more
11:27
8 Airbrush Regrets I WISH SOMEONE TOLD ME | Miniature Painting
9:43
Lyla Mev - The Mini Witch
Рет қаралды 68 М.
My scorpion was taken away from me 😢
00:55
TyphoonFast 5
Рет қаралды 2,7 МЛН
小丑女COCO的审判。#天使 #小丑 #超人不会飞
00:53
超人不会飞
Рет қаралды 16 МЛН
When you have a very capricious child 😂😘👍
00:16
Like Asiya
Рет қаралды 18 МЛН
EASY Airbrush Secrets You Need To Know | Miniature Painting
9:02
Lyla Mev - The Mini Witch
Рет қаралды 142 М.
10 TIPS for FLAWLESS AIRBRUSH PERFORMANCE & Solving Problems
36:34
The Art Workshop
Рет қаралды 27 М.
Airbrush Basics: I Made Every Mistake So You Don't Have To
20:05
Layering versus Glazing - Miniature Painting Techniques Explained
17:11
Doctor Faust's Painting Clinic
Рет қаралды 508 М.
Beginner Airbrush Problems SOLVED
8:49
Lyla Mev - The Mini Witch
Рет қаралды 200 М.
What I Wish I Knew BEFORE Buying all my Miniature Paints
11:59
Lyla Mev - The Mini Witch
Рет қаралды 113 М.
10 Tips for Better Airbrushing - HC 357
14:13
Vince Venturella
Рет қаралды 63 М.
Know Nothing About Airbrushes? START HERE.
24:47
Miniac
Рет қаралды 1,6 МЛН
The Most BASIC Mini Painting Tips I WISH SOMEONE HAD TOLD ME!
7:10
Lyla Mev - The Mini Witch
Рет қаралды 515 М.
Airbrush Workflow for Dummies
12:10
Squidmar Miniatures
Рет қаралды 203 М.
My scorpion was taken away from me 😢
00:55
TyphoonFast 5
Рет қаралды 2,7 МЛН