Airbrush Paint Tips that Help

[@AirbrushAsylum]

💥 Paint Tips you Should Know - kzbin.info/www/bejne/qGasdqtopaejpLs

[@barryallenflash1]

Thank you, thank you, thank you! I'm sooooo glad I subscribed to your channel. You have so much knowledge, especially for us beginners! The fact that you are willing to share it with the airbrush community is a blessing!! Cheers from Washington state!!

[@AirbrushAsylum]

Thank you SO much for being a subscriber and glad you enjoy the videos and find them helpful, all the very best from Australia 🙏

[@adrianwilliams763]

Thanks for sharing. As a newbie, appreciate the advice.

[@georgewilliamssr5230]

What is a good Air Brush cleaner. That you can use when spraying enamels. That won't eat up your O rings?

[@AirbrushAsylum]

I would recommend you get an airbrush with Teflon seals…when I used enamels over 10+ years ago I would clean with mineral turpentine , hope that helps 👍🏻

[@clives681]

Windex! Excellent cleaner!

[@alirowntree3989]

Brilliant nice easy too under stand great stuff

[@paulosilva4420]

I love all your videos and THANK YOU for sharing your knowledge and I ordered a Iwata Eclipse HP-CS and I'm so happy with its performance. Again, thanks to you Sir, I made a great purchase. 😁

[@peterwaghorn40]

Hello I bought some trident paints set and what do use to cleaner out the paint out of your air brush?

[@jobailey0042]

Great job thanks 😊

[@AirbrushAsylum]

You’re welcome 😊

[@RCBOSS1969]

Thanks man!

[@81artmonk]

Actually has a question regarding airbrushing fabrics. I airbrushed a white t-shirt and it was great. Tried on a black t-shirt and it was like the fabric didn't want to accept the paint. So I tried another color and it appeared to only be the case with black? I was using airbrush paint designed for fabric. Any suggestions as to what might have been going on or what to do in the future?

[@barryallenflash1]

What was the material? 100% cotton? Black "should" take the color like white, red, etc. The fabric is the key, but "shouldn't" keep you from airbrushing it no matter the color.

[@81artmonk]

@@barryallenflash1 The fabric was the same as the white. 100% cotton. I bought two black shirts and the paint would not adhere like it did with the white. It was weird

[@AirbrushAsylum]

Whenever I airbrush Black T-Shirts I use the trident tshirt booster first (apply 2 - 3 wet coats, this will seal the fibres and allow for quicker coverage of white to create your base) then heat set it before you begin airbrushing, then draw up your design and once complete re - seal with the Tshirt booster to help with longevity when washing.

[@HookedOnFishing61]

What size need are you using in this vid ? I'm using a black ridge airbrush and it cannot paint thinned paint let alone none thinned Haha. I think the needle in running is a .5 . Also those micro dots you did, very impressive, I can't wait until I can do those.

[@ConWest98]

I’m brand new to airbrushing but I do it for miniature painting. Does the rule of over thinning/ 1:1 ratio for paint to thinner still work for acrylic paints as well? Love the videos, just discovered your channel today!

[@LemurKrazy]

Some good tips - Thanks. Vortex mixers are great to Only ever used a tea strainer for primers. Where do you buy the paper strainers from?

[@seraajroomaney3148]

When mixing 50/50 don't forget the volume that tha marble in the jar takes up

[@AirbrushAsylum]

Yes , great point …something I never considered 🤦

[@jeffdeluca1153]

Thank you for the great tips from the USA! I have the Iwata HP-CS .35 tip. The Createx Airbrush Colors don't want to spray readily and Createx recommends no ore than 20% reducer. I see you reduced the Trident 1:1. What are your thoughts? Thank you Jeff

[@jakisprostylogin]

which notebook did you use in the presentation?

[@AirbrushAsylum]

It's just a A3 Art Pad available from most office supply stores, art stores as well as some dollar stores .

[@03Manne]

vielen dank mal wieder ein super Video 💯

[@AirbrushAsylum]

Danke 🙏🏻

[@manfredseidel1413]

Super Video vielen lieben Dank 👍

[@garryoldham8779]

Where can I get a pad like that to practice on, checked amazon and couldn’t find anything that big.

[@barryallenflash1]

I would check either Hobby Lobby or Michael's. Any craft store should have one.

[@Disc147]

Awesome man thanks

[@AirbrushAsylum]

No probs glad you enjoyed it 👍🏻

[@lawrencemccoy]

Thanks

[@AirbrushAsylum]

No probs glad you enjoyed it 👍🏻

[@atlredninja1]

Thank you!!!

[@AirbrushAsylum]

No probs 🙏🏻

[@DisVietVetUSA]

How ya doing there in Australia Mate?

[@AirbrushAsylum]

Doing well buddy, hope you are doing well also. 👍

[@mugen446]

Дякую

[@airbrushdungeon]

I'd like to Trident, but at $12.50 an Oz it ain't happening.

[@AirbrushAsylum]

Fair enough, Createx is also a great option I like the illustration colors also we sell trident at $14.95 AUD for 50ml (just under 2 oz) feel free to reach out and we can arrange shipping if you are outside of Oz 👍🏻

[@johnholmes4960]

Every time you change directions 180 degrees, the motion stops.

[@AirbrushAsylum]

My trigger finger is constantly moving back and forth whilst keeping the air pressed down , it may not be 100% visible as it’s second nature after 20+ years of airbrushing, thanks for raising the point as it is important to ensure that you are colouring in correctly 😉