Airgun - Install Altaros regulator to Daystate Huntsman Regal

  Рет қаралды 18,637

Altaros Airgun, Slugs and Accessories

Altaros Airgun, Slugs and Accessories

Күн бұрын

Пікірлер
@allanjames1934
@allanjames1934 6 жыл бұрын
Hi I genuinely want this modification on my Regal, could you let me know the full costings please
@111davcoy
@111davcoy 7 ай бұрын
What happens if you fully tighten the cylinder not leaving the slight gap to vent. Cheers
@AirgunRegulator
@AirgunRegulator 7 ай бұрын
The regulator needs contact with atmospheric pressure.
@anirudhpanwar6202
@anirudhpanwar6202 4 жыл бұрын
I have a classic...want to install a huma...why have you not reinstalled the two removed o rings
@AirgunRegulator
@AirgunRegulator 4 жыл бұрын
The 2 o-rings must be removed, as this creates a supply of atmospheric pressure to the regulator, which is necessary for its proper function. We were the first in the world to come up with this idea almost 10 years ago, and other regulator manufacturers ( including Huma ) began to copy our idea.
@anirudhpanwar6202
@anirudhpanwar6202 Жыл бұрын
@@AirgunRegulator ok...you have just removed only 2 screws from the top of the breech block cover and removed the air tube..is this ok.i also plan to strip my huntsman the same way since theres a leak in the pcp...
@anirudhpanwar6202
@anirudhpanwar6202 Жыл бұрын
118-SOLENOID SPACER O RING and 111 URETHANE-PISTON O RING...where do these fit in a daystate
@AirgunRegulator
@AirgunRegulator Жыл бұрын
unfortunately this is a question for Daystate,
@roberttheriot7612
@roberttheriot7612 3 жыл бұрын
HI; was that regulator set to 150 bar? trying to figure out why you put air half way into the yellow area. just trying to understand what's going on or how that works. i will be putting an Altaros regulator in my Daystate huntsman regal. Need to know as much as possible thanks
@AirgunRegulator
@AirgunRegulator 3 жыл бұрын
The regulator is sent set according to the required power or output pressure. It can be set as standard from 100 to 150 (170bar)
@roberttheriot7612
@roberttheriot7612 2 жыл бұрын
@@AirgunRegulator so if my regulator comes set @ 130 bar i pressure it up to 130 psi. this is what i am trying to understand. because right now is pressure it up to 3000 or 3200 psi without reg. thank you for your help
@AirgunRegulator
@AirgunRegulator 2 жыл бұрын
@@roberttheriot7612 I'm not entirely sure what you're asking. The conversion between bar and PSI is 1bar = 14.5 PSI. 3000 PSI is therefore about 207bar. The maximum outlet pressure from the regulator is about 190bar, but rather 175bar
@roberttheriot7612
@roberttheriot7612 2 жыл бұрын
@@AirgunRegulator i guess what i am trying to get at is if it comes set at 130 bar i would multiply 130 x 14.5 = 1885 psi if am correct. is it possible to put more air in the cylinder if the regulator is set @ 130 or do i set regulator to 170 bar where ever that maybe and fill to 2465 psi and that would be max. my regulator i think is 150 max. i guess in other words whatever your regulator is set @ say 130 bar you shouldn't put more than 1885 psi or it will mess up air rifle . also where is the 170 bar thank you very much
@AirgunRegulator
@AirgunRegulator 2 жыл бұрын
@@roberttheriot7612 You have the conversion to PSI correctly, but I don't think you understand exactly the function of regulator. The outlet pressure is set to any value in the range, but the airtube as such is always filled to the maximum pressure specified by the rifle manufacturer. In this case, it is necessary to fill the airtube according to the external manometer on the bottle. It is possible to shoot until the pressure on the manometer on the rifle begins to drop. At this point, it is necessary to refill the airtube at full pressure.
@chriswelljack4910
@chriswelljack4910 4 жыл бұрын
Why you took the grub screws all the way out
@roberttheriot7612
@roberttheriot7612 2 жыл бұрын
just finished installing altaros reg. seems like i couldn't fill to where i use to which is 3000 psi also it sounds really weak. hand pump was really hard to pump at about1500 psi. i thought you had told me that i could put what the manufacture required. so i tried and like i said earlier it was pretty hard to pump. you think i should try some more pumping. please let me know thanks
@AirgunRegulator
@AirgunRegulator 2 жыл бұрын
the regulator does not apply the maximum filling pressure in any way. When filling a rifle, there can be no difference between filling a regulated and unregulated rifle. The only essential thing I have already written is that it must be filled according to the external manometer in this case on the pump, NOT according to the manometer on the rifle, which no longer shows the pressure in the airtube.
@roberttheriot7612
@roberttheriot7612 2 жыл бұрын
@@AirgunRegulator thank you thank you and thank you again i think i am finally catching on. i know i'm a little slow at learning but thank you for your patients. my daystate was shooting around 875 fps before i installed the reg. and now it's shooting about 775. is that normal? i also turned in my hammer spring 2 full turns to see if it would do anything---not a thing different. you think if i take out the reg. and set it to 140 bar that it will shoot to a higher fps? thank you again
@AirgunRegulator
@AirgunRegulator 2 жыл бұрын
@@roberttheriot7612 hello , yes try set higher pressure. I would try set 150bar.
@Twoblaines
@Twoblaines 5 жыл бұрын
What is the spray you are using?
@AirgunRegulator
@AirgunRegulator 5 жыл бұрын
COYOTE Silkal 93, but a similar silicone spray can be used.
@ballkeeper6662
@ballkeeper6662 5 жыл бұрын
what stop the just coming out all the time and empty the cylinder,and what improvements will this give to my huntsman regal please
@AirgunRegulator
@AirgunRegulator 5 жыл бұрын
I'm not quite sure what you're asking. The air is launch by turning the manometer and then retightening the manometer to prevent leakage. The improvement after installing the regulator concerns the consistency of the muzzle velocity. The results are here at the bottom of the page. The smaller muzzle velocity change, the more accurate the rifle: www.altaros.cz/en/daystate/12-4771-daystate-airgun-regulator.html#/62-awpdetails-
@alsharifful
@alsharifful 4 жыл бұрын
Why the two O rings have nit been reinstalled in their original place please?
@AirgunRegulator
@AirgunRegulator 4 жыл бұрын
Removal of the original o-rings is therefore done for creates a supply of atmospheric pressure to the regulator spring.
@Igotknobblies
@Igotknobblies 3 жыл бұрын
Hi, I've done this with my huntsman regal xl using a Lancet regulator. Shot count has improved slightly but surprised at the drop in power, down to 25'Lb from 28'Lb! Tried everything to give higher power. I'm told that these guns are capable of up to 40'Lb. Obviously the hammer is a heavier version to the sub12'Lb, but is there difference between the 28'Lb and 40'Lb? Perhaps a heavier valve spring and hammer or any work yo the transfer port etc? TIA!
@roberttheriot7612
@roberttheriot7612 2 жыл бұрын
did you happen to figure your air gun out with ft.lbs. of energy. i'm in the same boat as you but maybe worse. i went from 30 ft.lbs. with no reg. to 21 ft. lbs. with altaros reg. very disappointed. even reset reg. to 150 bar from 125 bar and it barely sped up fps. if you happen to find out anything; would you mind helping me out. thanks
@Abdulkarim554
@Abdulkarim554 6 жыл бұрын
what is the difference between this regulator and the other which was installed through the front side? and can I install the quick fill kit with this regulator?
@AirgunRegulator
@AirgunRegulator 6 жыл бұрын
The difference is that this version has a connection with the atmospphere throught the thread at tle plug. Yes with bouth version you can used a quick fill.
@dukebeach1
@dukebeach1 6 жыл бұрын
Will this regulator work with the Huntsman Regal XL tube? If not, do you make one for that model? Thanks
@AirgunRegulator
@AirgunRegulator 6 жыл бұрын
If the airtube is one piece together with the lower body of the rifle, then this regulator can not be used. If it has a screwed airtube as here on the video, it should be possible to use this regulator.
@digga1667
@digga1667 6 жыл бұрын
Video title states huntsman regal.........but that's a classic you're working on.......is installation that easy as I've read comments elsewhere stating drilling the cylinder and transfer port........
@AirgunRegulator
@AirgunRegulator 6 жыл бұрын
This nomenclature differs from the Web site. There is a classic name on the rifle, but elsewhere it was presented as a regal. The key is whether your rifle has a split airtube or is an airtube and a body from one tube. Accordingly, it is possible to solve it that regulator can by used. This regulator can by used only form split airtube. At none of our regulator does not need drill hole in to airutbe and airgun it is always possible to return to its original state!
@Igotknobblies
@Igotknobblies 4 жыл бұрын
No drilling required as the reg vents to atmosphere as required through the threads (hence removing the two original o ring seals). There is a chance that overtightening the reservoir could actually seal the end of the tube. A tiny score on the block with the male thread will ensure this doesn't happen. Clearance in the thread is such that enough air movement will ocurr.
@rubenherrerab.5122
@rubenherrerab.5122 6 жыл бұрын
the manometer will mark the pressure of the regulator and not that of the deposit, it is correct!
@AirgunRegulator
@AirgunRegulator 6 жыл бұрын
yes, after installing the regulator gauge on the rifle shows the regulated pressure
@susiemaeabuton4415
@susiemaeabuton4415 2 жыл бұрын
Can i buy a receiver only?
@AirgunRegulator
@AirgunRegulator 2 жыл бұрын
we only offer pressure regulators, not rifle parts
@susiemaeabuton4415
@susiemaeabuton4415 2 жыл бұрын
@@AirgunRegulator price of pressure regulator? and kindly send me a picture with specification....thank you sir
@AirgunRegulator
@AirgunRegulator 2 жыл бұрын
@@susiemaeabuton4415 Hello, www.altaros.cz/22-daystate
@agungkurniadi5447
@agungkurniadi5447 4 жыл бұрын
Hi, what type this product ?
@AirgunRegulator
@AirgunRegulator 4 жыл бұрын
in case of interest, please write to altaros@altaros.cz and you will receive a fully reply on the first working days. Thank you
@chriswelljack4910
@chriswelljack4910 4 жыл бұрын
Open the bag and put it over the tube that wat it will stay in place
@Twoblaines
@Twoblaines 5 жыл бұрын
Thanks for the information.😃
@pomo7496
@pomo7496 Жыл бұрын
用手拧表很不专业
Daystate Huntsman Regal XL REVIEW
10:43
airgunsofarizona
Рет қаралды 85 М.
Airgun - Install Altaros regulator to BSA Buccaneer SE
4:45
Altaros Airgun, Slugs and Accessories
Рет қаралды 34 М.
REAL or FAKE? #beatbox #tiktok
01:03
BeatboxJCOP
Рет қаралды 18 МЛН
小丑女COCO的审判。#天使 #小丑 #超人不会飞
00:53
超人不会飞
Рет қаралды 16 МЛН
Daystate Regal regulator and quick fill wika gauge
14:05
Air Rifle Tech
Рет қаралды 11 М.
Daystate Huntsman Regal XL Air Rifle
2:28
airgunsofarizona
Рет қаралды 158 М.
1 Mile - World Record Longest Airgun Hit
12:45
Altaros Airgun, Slugs and Accessories
Рет қаралды 9 М.
Lane Regulators - FAQ1a - What happens if the regulator cannot breath?
7:40
Daystate Factory Tour by AOA
12:17
airgunsofarizona
Рет қаралды 89 М.
How Air Rifle Works ? (PCP Air Gun Works Animation)
5:53
Amrie Muchta
Рет қаралды 563 М.
Airgun - Install Altaros regulator and quick fill to AirArms S400
13:39
Altaros Airgun, Slugs and Accessories
Рет қаралды 24 М.
How a PCP Airgun Works | AB101 pt. 3
9:07
AirArmsHuntingSA
Рет қаралды 898 М.